1. Manuals
  2. Brands
  3. Hunter Manuals
  4. Fan
  5. 20578
  6. Quick start manual and installation manual

Hunter 20578 Quick Start Manual And Installation Manual

Owner's manual
Hide thumbs Also See for 20578:

Advertisement

Table of Contents

See also: Manual Del Usuario

Advertisement

Table of Contents
loading

Related Manuals for Hunter 20578

Summary of Contents for Hunter 20578

  • Page 5: Table Of Contents

    7 • Assembling the Blades ..............................................14 8 • Activating Auto Balance ............................................15 9 • Completing Your Installation With a Bowl Light Fixture ................................................16 10 • Removing the Light Fixture .............................................19 11 • Operation & Maintenance ............................................21 42798-01 • 12/28/09 • Hunter Fan Company...

  • Page 6: Getting Ready

    Congratulations! Checking Your Fan Parts Your new Hunter ceiling fan is an addition to your home or office that Carefully unpack your fan to avoid damage to the fan parts. Refer to will provide comfort and reliable performance for many years. We are the included Parts Guide.
  • Page 7 If you want to use an existing fan site, complete the following checklist to determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
  • Page 8 Section 2 • Installing the Ceiling Step 5 Plate. CAUTION: All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. 42798-01 • 12/28/09 • Hunter Fan Company...

  • Page 9: Installing The Ceiling Mounting Plate

    Your ceiling mounting plate (2) comes with four pre-installed noise middle of the ceiling mounting plate (2). isolators (71). Check to make sure all four isolators are in place and were not removed during shipment. 42798-01 • 12/28/09 • Hunter Fan Company...
  • Page 10 Unbundle the wires from the fan. that the two tabs are pointing toward the ceiling peak. Note: Your Hunter fan comes with an optional pipe/ball assembly extension pipe. If you are hanging the fan on a ceiling higher than 10 feet tall and you would like to use the enclosed optional pipe/ball assembly, –...

  • Page 11: Assembling And Hanging The Fan

    (2). Note: To hang the fan, you must tilt the ceiling mounting plate cover (3) to an almost vertical position so that the ceiling mounting plate cover (3) slots sit on the ceiling mounting plate hooks. 42798-01 • 12/28/09 • Hunter Fan Company...
  • Page 12 Extension Pipe Optional Pipe/Ball Instructions: Your Hunter fan comes with an optional pipe/ball assembly extension Place the slots over the hooks to hang the fan. pipe. If you would like to use the enclosed optional 6 inch pipe/ball assembly, follow Steps 3.6-3.9. Note: The Auto Balance system is designed for pipe/ball assemblies that are 6”...

  • Page 13: Setting The Remote Transmitter And Receiver

    The DIP switches for the receiver (86) are located on the flat surface of the receiver. The jumpers for the transmitter (87) are in the battery battery is not connected to the transmitter. Also, make sure the power is compartment. still off. 42798-01 • 12/28/09 • Hunter Fan Company...
  • Page 14 The remote control device complies with part 15 of the FCC rules. Changes or (87). Clean the battery contacts and also those of the device prior to modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment. Operation is subject to the following two battery installation.

  • Page 15: Wiring The Fan

    (grounding) from the ceiling connector (70) over them, then twist clockwise until tight. For all these mounting plate and the green ground wire from the pipe/ball assembly connections use the wire connectors provided. (7). 42798-01 • 12/28/09 • Hunter Fan Company...
  • Page 16 • The white wire from the fan to the white wire from the receiver (marked on outlet box. Position the receiver (86) in the ceiling mounting plate cover so white tag “COMMON OUT”) that the antenna is close to the edge for clear reception. 42798-01 • 12/28/09 • Hunter Fan Company...

  • Page 17: Installing The Ceiling Plate Cover

    The ceiling mounting plate the trim ring (4). The tabs will flex out releasing the ceiling mounting plate cover trim ring (4). cover trim ring will snap and lock into place. 42798-01 • 12/28/09 • Hunter Fan Company...

  • Page 18: Assembling The Blades

    Slide the blade arms (44) onto the blade-to-arm screws (47). Tighten the the shipping bumpers in place. Push the shipping bumpers in, then lift blade-to-arm screws (47) as tight as possible with a screwdriver. them off. 42798-01 • 12/28/09 • Hunter Fan Company...

  • Page 19: Activating Auto Balance

    Rotate the blades slowly until one of the red retaining screws is visible through the notch in the mounting plate. Remove the retaining screw from the bottom of the fan housing using a screwdriver. Repeat this process for all 5 retaining screws. 42798-01 • 12/28/09 • Hunter Fan Company...

  • Page 20: Completing Your Installation With A Bowl Light Fixture

    (30). mounting plate. Your Hunter fan comes with an integrated light fixture assembly and an optional Align the keyhole slots in the upper switch housing with the inner switch switch housing cap and plug button. This feature gives you the option of installing housing screws (69).
  • Page 21 Thread the pull chains through the grommet holes on the sides of the Install the included Pin-Based CFL bulb (259), 26 Watt Maximum, into the socket. bracket. Then, thread them through the holes in the metal disc. 42798-01 • 12/28/09 • Hunter Fan Company...
  • Page 22 Screw the finial (149) onto the threaded finial rod end until tight. You can mount the remote holder to any toggle switch plate with the screws already in the switch plate. Or, you can simply mount the remote holder on the wall. 42798-01 • 12/28/09 • Hunter Fan Company...

  • Page 23: Removing The Light Fixture

    Remove the nut and washer from inside the center of the lower switch Disconnect the plug connectors between the black wire and the black housing. wire with a white stripe. Disconnect the plug connectors between the two white wires. 42798-01 • 12/28/09 • Hunter Fan Company...
  • Page 24 Install the switch housing cap and plug button to the lower switch connector in the lower switch housing. Attach the lower switch housing to housing. the upper switch housing with three housing assembly screws. 42798-01 • 12/28/09 • Hunter Fan Company...

  • Page 25: Operation & Maintenance

    2. Check to see if the blade is cracked. If so, replace all the blades. have trouble, visit our Web site at: http://www.hunterfan.com. Hunter Fan Company 7130 Goodlett Farms Parkway #400 Memphis, Tennessee 38016 42798-01 • 12/28/09 • Hunter Fan Company...
  • Page 26 11 • Operation & Maintenance Hunter fans have the power to cut your cooling costs up to 40%. Beat the High Cost of Cooling The air movement created by a Hunter ceiling fan lets you set your thermostat higher and still stay comfortable. Every degree you raise the thermostat saves up to 7% on energy costs.

This manual is also suitable for:

Park hill type 2

Table of Contents