9 • Troubleshooting . . . . . . . . . . . . . . . . . . . . 17 • To reduce the risk of fire, electrical shock, or motor damage, do not use a solid-state speed control with this fan . Use only Hunter speed controls .
If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan . If you cannot check off every item, prepare a new fan site as described on this page .
Page 4
ANSI/NFPA 70 . If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Ceiling Plate. qualified electrician . 42751-01 • 08/12/10 • Hunter Fan Company...
Page 5
Support Brace Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease . You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting . The steps in this manual include Ceiling instructions for all three Installer’s Choice mounting methods .
Parts Guide . Check for any shipping damage to the motor blade irons (if applicable) in sets, or fan blades . If any parts are missing or damaged, contact your Hunter as they were shipped . dealer or call Hunter Technical Support Department at 888-830-1326 (In Canada, call 1-866-268-1936) .
. Do not over tighten . Flat Washer 3” Wood Screw For Angled Ceilings: Be sure to orient the ceiling plate so that the arrows printed on the ceiling plate are pointing toward the ceiling peak . 42751-01 • 08/12/10 • Hunter Fan Company...
Assemble securely with three low profile screws . 3-7 . Raise the fan and place the hook on the ceiling plate through the U-shaped hole in the rim . Low Profile Screw Step 3-7 U-shaped Hole 42751-01 • 08/12/10 • Hunter Fan Company...
. 4-7 . Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box . 42751-01 • 08/12/10 • Hunter Fan Company...
2 . Press firmly on opposite sides of the ring toward the canopy . The tabs will flex out releasing the trim ring from the canopy . Step 5-3 Steps 5-4 – 5-5 Canopy Screw 42751-01 • 08/12/10 • Hunter Fan Company...
6 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan) . 6-1 . Install the grommets into the blades by hand . Step 6-1 (Detail) 6-2 . Place each blade between a blade iron and medallion . Install three blade screws to attach the medallion to the blade iron .
7 • Completing Your Installation With or Without a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button . This feature gives you the option of installing the fan with OR without the included light fixture .
Page 13
Detail hazard or improper operation . If lights do not appear to be operating properly, see the troubleshooting section . Housing Assembly Screw 42751-01 • 08/12/10 • Hunter Fan Company...
Page 14
. (You may find the Light Bulbs breakaway connector on the (B10 Candelabra end of the extra chain . ) Base 60 Watt Maximum) Metal Rod Metal Disk Glass Bowl Cover Plate Breakaway Finial Connector 42751-01 • 08/12/10 • Hunter Fan Company...
Page 15
7-20 . Install the switch housing cap and plug button to the lower switch housing . 7-21 . Once you have uninstalled the light fixture, continue Steps 7-17 – 7-19 with step 7-6 . Male Dummy Terminal Female Dummy Terminal Plug Button Step 7-20 42751-01 • 08/12/10 • Hunter Fan Company...
. 8-6 . The blades on this fan have been treated with Hunter’s Dust Armor protection, making the blades less likely to attract dust and dirt . Use a dry or slightly damp lint free cloth to clean the In cold weather, use upward blades .
888-830-1326 (In Canada, call 1-866-268-1936) or visit us at our Web site at http://www . h unterfan . c om . Hunter Fan Company 7130 Goodlett Farms Pkwy . #400 Memphis, Tennessee 38016 42751-01 • 08/12/10 • Hunter Fan Company...