Combinations Of Cutting Attachments, Deflectors And Carrying Systems - Stihl FSA 120.0 R Instruction Manual

22 Combinations of Cutting Attachments, Deflectors and Carrying Syst...
If the battery is wet or moist, allow the battery to
dry for at least 48 h between 15°C and 50°C and
with less than 70% humidity. Higher humidity
may extend the drying time.
21.5 Sound Values and Vibration
Values
The K value for the sound pressure level is
2 dB(A). The K value for the sound power level is
2 dB(A). The K value for the vibration level is
2 m/s².
STIHL recommends wearing hearing protection.
Using with a mowing head except PolyCut 18-2
– Sound pressure level L
fied in IEC 62841‑4‑4: 81 dB(A)
– Sound power level L
ance with IEC 62841-4-4: 94 dB(A)
– Vibration value a
hv
IEC 62841-4-4
– Control handle: 2.8 m/s²
– Loop handle: 5.8 m/s²
Using with a PolyCut 18-2 mowing head
– Sound pressure level L
fied in IEC 62841‑4‑4: 82 dB(A)
– Sound power level L
ance with IEC 62841-4-4: 93 dB(A)
– Vibration value a
hv
IEC 62841-4-4
– Control handle: 1.6 m/s²
– Loop handle: 3.2 m/s²
22 Combinations of Cutting Attachments, Deflectors and Carrying
Systems
22.1

Combinations of cutting attachments, deflectors and carrying systems

Cutting attachment
– PolyCut 18-2 mowing head
(Ø 335 mm)
Mowing head with "round,
quiet" mowing lines with a
diameter of 2.4 mm:
– AutoCut 25-2 mowing head
– AutoCut C 26-2 mowing
head
– AutoCut 27-2 mowing head
– DuroCut 20-2 mowing head
– SuperCut mowing head
20-2
– TrimCut C 32-2 mowing
head
– Grass cutting blade 230-2
(Ø 230 mm)
– Grass cutting blade 230-4
(Ø 230 mm)
0458-029-0101-A
measured as speci‐
pA
measured in accord‐
wA
measured as specified in
measured as speci‐
pA
measured in accord‐
wA
measured as specified in
Deflector
– Deflector for
mowing heads
(Ø 380 mm)
– Deflector for
metal cutting
attachments (Ø
230 mm)
Using with a metal cutting attachment
– Sound pressure level L
fied in IEC 62841‑4‑4: 81 dB(A)
– Sound power level L
ance with IEC 62841-4-4: 94 dB(A)
– Vibration value a
IEC 62841-4-4
– Control handle: 2.9 m/s²
– Loop handle: 3.7 m/s²
The vibration levels indicated were measured
according to a standardized test method and can
be used as a basis for comparing electric power
tools. The vibration levels actually occurring may
vary from the values indicated, depending on the
type of application. The vibration levels indicated
can be used for an initial estimate of the vibration
stress. The actual vibration stress has to be esti‐
mated. The times can be taken into account in
the estimate when the electric power tool is
switched off and also when it is switched on but
running without any load.
For information on compliance with the Physical
Agents (Vibration) Directive 2002/44/EC, see
www.stihl.com/vib.
21.6 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
Barrier bar Carrying system
– optional – Shoulder strap
– Full harness with quick-
– STIHL AR battery with the
– Battery belt with attached
– Battery belt with strap and
– Carrying system with built-in
– required
measured as speci‐
pA
measured in accord‐
wA
measured as specified in
hv
release system
support cushion
"AP belt bag with connecting
cable" together with the
shoulder strap
attached "AP belt bag with
connecting cable" together
with the support cushion
"AP belt bag with connecting
cable" together with the sup‐
port cushion
English
21