Combinations Of Cutting Attachments, Deflectors And Carrying Systems - Stihl FSA 200.0 R Instruction Manual

22 Combinations of Cutting Attachments, Deflectors and Carrying Syst...
21.3 Temperature limits
WARNING
■ The battery is not protected against all ambi‐
ent conditions. If the battery is exposed to cer‐
tain environmental conditions, it may catch fire
or explode. This may result in serious injury to
people and damage to property.
► Do not charge the battery below -20°C or
above 50°C.
► Do not use the brushcutter or battery below
-20°C or above 50°C.
► Do not store the brushcutter or battery
below -20°C or above 70°C.
21.4 Recommended temperature
ranges
For optimum performance of the brushcutter and
battery, note the following temperature ranges:
– Charging: 5°C to 40°C
– Use: - 10 °C to + 40 °C
– Storage: - 20 °C to + 50 °C
If the battery is charged, used or stored outside
the recommended temperature ranges, perform‐
ance may be restricted.
If the battery is wet or moist, allow the battery to
dry for at least 48 h between 15°C and 50°C and
with less than 70% humidity. Higher humidity
may extend the drying time.
21.5 Sound Values and Vibration
Values
The K value for the sound pressure level is
2 dB(A). The K value for the sound power level is
2 dB(A). The K-value for vibration level is 2 m/s².
STIHL recommends wearing hearing protection.
Using with a mowing head except PolyCut 28-2
– Sound pressure level L
ance with IEC 62841-4-4: 80 dB(A)
– Sound power level L
ance with EN IEC 62841-4-4: 94 dB(A)
– Vibration value a
hv
with IEC 62841-4-4
22 Combinations of Cutting Attachments, Deflectors and Carrying
Systems
22.1

Combinations of cutting attachments, deflectors and carrying systems

Cutting attachment
– PolyCut 28-2 (365 mm dia‐
meter)
0458-041-9601-A
measured in accord‐
pA
measured in accord‐
wA
measured in accordance
Deflector
– Universal
deflector with
– Control handle: 3.0 m/s²
– Loop handle: 3.8 m/s²
Use with a PolyCut 28-2 mowing head
– Sound pressure level L
ance with IEC 62841-4-4: 87 dB(A)
– Sound power level L
ance with IEC 62841-4-4: 98 dB(A)
– Vibration value a
with IEC 62841-4-4
– Control handle: 3.1 m/s²
– Loop handle: 4.3 m/s²
Use with a metal cutting attachment
– Sound pressure level L
ance with IEC 62841-4-4: 85 dB(A)
– Sound power level L
ance with IEC 62841-4-4: 106 dB(A)
– Vibration value a
with IEC 62841-4-4
– Control handle: 3.5 m/s²
– Loop handle: 4.1 m/s²
The vibration levels indicated were measured
according to a standardized test method and can
be used as a basis for comparing electric power
tools. The vibration levels actually occurring may
vary from the values indicated, depending on the
type of application. The vibration levels indicated
can be used for an initial estimate of the vibration
load. The actual vibration load has to be estima‐
ted. The times can be taken into account in the
estimate when the electric power tool is switched
off and also when it is switched on but running
without any load.
For information on compliance with the Vibration
Directive 2002/44/EC, see www.stihl.com/vib.
21.6 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
Barrier bar Carrying System
– optional – Shoulder strap
measured in accord‐
pA
measured in accord‐
wA
measured in accordance
hv
measured in accord‐
pA
measured in accord‐
wA
measured in accordance
hv
English
51