Safety; Safe Operating Practices - Toro 30487N Operator's Manual

Safety

Machines with model numbers 30495, and 30487 meet or
exceed CEN standard ISO EN 5395 and ANSI B71.4-2012
specifications in effect when the proper CE Kits have been
installed per the Declaration of Conformity. Machine with
model number 30487N meets or exceeds ANSI B71.4–2012
specifications in effect at the time of production
Improper use or maintenance by the operator or owner can
result in injury. To reduce the potential for injury, comply
with these safety instructions and always pay attention to the
safety alert symbol, which means Caution, Warning, or
Danger—personal safety instruction. Failure to comply with
the instruction may result in personal injury or death.

Safe Operating Practices

The following instructions are adapted from the CEN
standard EN 836:1997 and ANSI B71.4-2012.
This product is capable of amputating hands and feet and
throwing objects. Always follow all safety instructions to
avoid serious injury or death.
Training
•
Read the Operator's Manual and other training material
carefully. Be familiar with the controls, safety signs, and
the proper use of the equipment.
•
Never allow children or people unfamiliar with these
instructions to use the lawn mower. Local regulations can
restrict the age of the operator.
•
Never mow while people, especially children, or pets are
nearby.
•
Keep in mind that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
•
Do not carry passengers.
•
All drivers should seek and obtain professional and
practical instruction. Such instruction should emphasize:
– the need for care and concentration when working
with ride-on machines;
– control of a ride-on machine sliding on a slope will
not be regained by the application of the control
levers. The main reasons for loss of control are:
◊ insufficient wheel grip, especially on wet grass;
◊ being driven too fast;
◊ inadequate braking;
◊ the type of machine is unsuitable for its task;
◊ lack of awareness of the effect of ground
conditions, especially slopes;
◊ incorrect load distribution.
Preparation
•
While mowing, always wear substantial footwear and long
trousers. Do not operate the equipment when barefoot
or wearing open sandals.
•
Thoroughly inspect the area where the equipment is to
be used and remove all objects which may be thrown by
the machine.
•
Replace faulty silencers/mufflers.
•
Before using, always visually inspect to see that the blades,
blade bolts and cutter assembly are not worn or damaged.
Replace worn or damaged blades and bolts in sets to
preserve balance.
Safe Handling of Fuels
•
To avoid personal injury or property damage, use extreme
care in handling fuel. Fuel can be is extremely flammable
and the vapors are explosive.
•
Extinguish all cigarettes, cigars, pipes, and other sources
of ignition.
•
Use only an approved fuel container.
•
Never remove fuel cap or add fuel with the engine
running.
•
Allow engine to cool before refueling.
•
Never refuel the machine indoors.
•
Never store the machine or fuel container where there is
an open flame, spark, or pilot light such as on a water
heater or on other appliances.
•
Never fill containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place containers on
the ground away from your vehicle before filling.
•
Remove equipment from the truck or trailer and refuel it
on the ground. If this is not possible, then refuel such
equipment with a portable container, rather than from a
fuel dispenser nozzle.
•
Keep the nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is complete.
Do not use a nozzle lock open device.
•
If fuel is spilled on clothing, change clothing immediately.
•
Never overfill fuel tank. Replace fuel cap and tighten
securely.
Operation
•
Be alert, slow down and use caution when making turns.
Look behind and to the side before changing directions.
•
Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect.
•
Mow only in daylight or in good artificial light.
•
Before attempting to start the engine, disengage all blade
attachment clutches and shift into neutral.
4