Kenwood TS-950SDX Instruction Manual page 27

spi Be
57
|"Rpt.tone" Used to select the desired Sub- tone frequency.
| 88.5 Hz
58
|"Con bst" Selects the desired Sub-tone type burst (b) or continuous (c).
c
SSB: 1
59
| "Agc set" Selects the AGC time constant in the AUTO position(SSB, CW ).
CW: 3
1=SLOW
2=MID
3= FAST
FSK
60
"Shift" Allows temporary adjustment of frequency in the memory channel recall mode,
OFF
without affecting the contents of the memory channel when ON.
i
61
"Band.sel" Selects the desired memory saving mode.
ALL
HALF: 1 (Frequency only)
ALL: 2 (Frequency, Mode, filter etc.)
OFF
f
62
"Auto.inc" Allows the memory channel number to be automatically increased each time the
OFF
M.CH key is pressed when ON.
"Step" Selects the desired frequency step size of the main tuning knob. (5kHz or 10kHz)
63
Does not effect the tuning rate when the FINE function has been selected, or when the 10kH.
SSB, CW, or FSK mode has been selected.
}
£
In the FM mode the selection options are 25kHz or 50kHz.
:
64
"Ch step" Allows the M.CH/VFO CH control step size to be adjusted within a range of 1kHz
OkHz
to 10kHz. {in 1KHz increments)
"Ch step"
Allows the M.CH/VFO CH control step size to be 9kHz or 10kHz in the broadcast band
10kHz
only during AM operations.
d?
;
an
"Up dn f" Allows the UP/DOWN key frequency step size to be adjusted within a range of 1000
1kHz to 10kHz (in 1kHz increments), 500kHz or 1MHz.
kHz
67
"Rit.disp" When turned on, Allows display of the RIT/XIT frequency when the RIT/XIT switch
ON
is off.
|"Rit.plus" Turns the RIT/XIT frequency change data transfer function ON or OFF.
68
When ON, allows the frequency change data to be copied into the main display when the
OFF
CLEAR key is pressed.
69
"Chatter" Turns the electronic keyer chatter suppression circuit ON or OFF. Menu 12 must ON
be On for this menu choice to become available.
70
"Cp" Sets the CW mode to SEMI when transmitting a CW message ON or OFF.
OFF
Menu 12 must be ON for this menu choice to become active.
71
|"Ssb auto" Turns the SSB auto mode function ON or OFF.
| ON
72
'"Scan hid" Turns the program scan hold function ON or OFF.
OFF
73
| "Fil sel" Turns the filter limit selection function. This allows useful filter selections to be ON
made, based upon the mode of operation. Example: No 270 Hz filter for SSB voice.
74
|"10 disp" Turns the 10Hz display resolution ON or OFF.
' ON
75
|"Scale" Sets the full scale deflection of the Analog scale to MHz or 100kHz.
ee
76
"Split" Allows you to disable the frequency display shift that occurs during split frequency
OFF
| operations.
i "Scope" Turns the Sub receiver marker ON and OFF when using the SM-230 in the Pan
77 | Display mode, with a 100 kHz or 250 kHz resolution. The scope maker is not quite as stable
| OFF
as the main display and might tend to drift slightly as time goes by.
78
"Sub chg"You can set the RX—SUB key either to switch between the MAIN and SUB
CHANGE
frequencies (CHANGE) or to transfer the Main frequency to the Sub frequency {COPY}.
"Synchro" Sets whether to enable (ON) or disable (OFF) the transmitter function (A(VFO A)
79
TX key, B(VFO B) TX key, or M.CH (memory channel) TX key when you press a receiver
ON
27