Harman Kardon AVR 435 Owner's Manual page 40

ADVANCED FEATURES
PresstheSetButtonli_ii. toenterhe
ADVANCED SELECTmenu.
When the ADVANCED
SELECT
menu
appears, pressthe A/V NavigationButton
sothatthe cursoris pointing to the SE MI
0 S D/ T I ME 0 U T line.Select o neof these
options:
• Tokeepthesemi-OSD system activated, butto
adjustthe length of timethe displays remain on the
screen, p ressthe,/, NavigationButton
untilthedesired time out isshown. T hedefault
setting is 5 seconds.
• Toturnthe semiOSDsystem off sothatit doesnot
appear a t anytime.pressthe ,/1_ Navigation
Button _ so that0 F F is shown on the right
sideof the line.
Ifyouwishto makeotheradjustments, pressthe
•,/• NavigationButton _ untilthecursoris next
tothe desired settingor the BA CK T 0 MAS -
T E R MEN U lineandpresstheSet Button li_iJ. If
youhaveno otheradjustments to make. p ressthe
OSDButton _ to exitthe menusystem.
FulI-OSD Time-OutAdjustment
TheF UL L 0 SD menusystem is usedto simplify
thesetupandadjustment of theAVR435 by using a
series of on-screen menus. Thefactorydefault s etting
forthesemenusleaves themonthe screen for 20
seconds aftera periodof inactivity before theydisap
pearfromthe screen (TimeOut). T imeOutisa safeb/
measure to prevent i mageretention of themenutext
inyourmonitor or projector, whichmighthappen if it
werelefton indefinitely. However. someviewers may
prefer a slightly longeror shorter p eriodbefore the
on screen display disappears.
_,)change thefullOSDTme Out.youwillneed
to makeanadjustment inthe A DV AN CE D
SE L EC T menu(Figure 17).7o start t he adlust-
ment.presstheOSDButton _ to bringthe
MA ST E R MENU to the screen. P ress the •
NavigationButton li]_. unSl the on screen .->
cursor i s nextto the AD VAN CE D line. P ress the
Set Button _ to enterthe ADV AN CED
SE L EC T menu(Figure 22).
Atthe ADVANCED SELECT menu(Fig. 2 2)
makecertain thatthecursoris nextto the F UL L
0 S D T I ME 0 U T lineby pressing t he A/V
NavigationButton _ asneeded. N extpressthe
_/_ NavigationButton _ untilthedesired timeis
displayed i nseconds. U nlike mostof the otheroptions
inthismenu. t hisis a permanent settingchange, and
theTimeOutentrywill remain ineffectuntilit is
changed, e venif the unitisturnedoft
If youwishto makeotheradjustments, pressthe
A/V NavigationButton _ untilthe cursoris
nextto thedesired settingor the BA CK T 0
MA ST ER ME NU lineandpressthe Set Button
li_i_.Ifyou haveno otheradjustments to make.press
the OSDButton _ to exitthe menusystem.
OigitalAuto-PollSettings
InoTder t o provide thegreatest f lexibilify i naccom
modating thewidestrangeof sources, theAVR435
includes bothanalog anddigitalaudioinputs forall
sources. In mostcases youwillwantto useoneor the
other, b ut notboth.However. insomecircumstances it
is desirable to makebothan analog anddigitalcon-
nection bebJveen a sourcedevice andthe A\/R.
An important application f or dual a udioconnections i s
withcableor satellite boxes, w here the audiooutput
maychange depending on thechannel b eingviewed
andthe fypeof audiothe cablesystem or satellite
receiver a ssociates w ithit.Toeliminate t he need to
constantly s witchbackandforto select a n audiotype
eachtimeyouchange channels, theA\/R435 ispro
grammed by default t o automatically "poll"the audio
inputs. W henadigitalaudiostreamit is sebcted first.
but if the digital a udiois removed theAVRwillswitch
to the analog inputs associated w iththatinputasa
back-up, i nmostsystems t hisisthe correct o perallon
andnofurtherchange is required.
However. if thisconfiguration d oesnotsuityoursys
ternapplication t heAVR435 givesyoutheflexibilify
to turnthedigitalaudioautopolling on or off on an
inputby inputbasis. W hentheAutoPolling is setto
0 F F. thesystem will keepthe digital a udioinput
active andnotattempt t o switchto theanalogsource
evenwhenthedigitaldatastream stops.
Ifyou wishto change the autopollsetting, f irstselect
the inputyouwishto configure bypressing the @pro
priateInput SelectorOli'l on the remote, or on
the SOURCElinepftheIN/OUT SETUP
menu(Figure 2). Next. w iththe A DV AN CE D
SE L E CT ME NU (Figure 22) on thesemen.
pressthe _/1_ NavigationButton _ sothatthe
cursoris pointing to the AU T 0 P 0 L L line.Press
the _/_ NavigationButton _ to change a default
settingsothat0 F F isshowninhighlighted v ideoor
to 0 N so thatthe original settingis restored andthe
autopollingis onceagainactivated.
Sincethissettingis unique to eachinput, y ou
mustreturn to the I N PU T SE T U P menuto
change anyotherinputs. Todothat.pressthe _/1_
NavigationButton _ so thatthecursoris
pointing to the BACK
TO MASTER MENU
lineandpressthe Set Button li_iJ. At the
MASTER MENU (Figure 1).pressthe,/,
NavigationButton _ sothatthe cursoris pointing
to the I N / 0 UT S ET UP line.Press the Set
Button _ andthenfollowthe instructions shownon
pagexxto change the inputsource. R eturn to the
A DV AN CE D MENU to reconflgure t he auto
pollsettingforthe newly selected input.
Whenall changes t o theAutoPoll s ettings havebeen
made. p ressthe _/_ NavigationButton
to selectanother c onfiguration opSon on the
ADVANCED SETUP Menu.movethecursor
to BACK TO MASTER MENU lineandpress
the Set Button _ to makea change to anof:ser
menuoption, o r simplypressthe OSDButton
to exitthe menusystem.