Hitachi LH1 Series Basic Manual page 88

Chapter 4
[Hd202] to [Hd237]
2nd motor When Intelligent Input terminal 024[SET] is enabled.
Code/Name
Hd202
Sync. Motor capacity setting, 2nd-motor
Hd203
Sync. Motor number of poles setting,
2nd-motor
Hd204 Sync. Base frequency setting,
2nd-motor
Hd205 Sync. Maximum frequency setting,
2nd-motor
Hd206 Sync. Motor rated voltage,
2nd-motor
Hd208 Sync. Motor rated current,
2nd-motor
Hd210 Sync. Motor constant R,
2nd-motor
Hd212 Sync. Motor constant Ld,
2nd-motor
Hd214 Sync. Motor constant Lq,
2nd-motor
Hd216 Sync. Motor constant Ke,
2nd-motor
Hd218 Sync. Motor constant J,
2nd-motor
2nd motor When Intelligent Input terminal 024[SET] is enabled.
Code/Name
Hd230 Minimum frequency adjustment for
Sync.M, 2nd-motor
Hd231 No-Load current for Sync.M,
2nd-motor
Hd232 Starting method for Sync.M, 2nd-motor
Hd233 IMPE 0V wait number for Sync.M,
2nd-motor
Hd234 IMPE detect wait number for Sync.M,
2nd-motor
Hd235 IMPE detect number for Sync.M,
2nd-motor
Hd236 IMPE voltage gain for Sync.M,
2nd-motor
Hd237 IMPE Mg-pole position offset,
2nd-motor
[oA-10] to [oA-33][ob-01] to [ob-04]
■Parameter mode (o code)
Range Initial ・"o" parameters are displayed by the [UA-22] = 01. This
(unit) value
configuration is not necessary except when option is used.
・The implementation of the following parameters might differ
Same as Hd102
depending on the type of option being used. For more
information, contact to your supplier or local Hitachi distributor
or service station.
Same as Hd103
Optional cassette error operation
Same as Hd104
Same as Hd105 oA-10
at an option error (SLOT-1)
Same as Hd106
oA-11
Same as Hd108 Watch Dog Timer (SLOT-1)
oA-12
Same as Hd110
a communication error
Same as Hd112
(SLOT-1)
Same as Hd114
oA-13
selection at start up (SLOT-1)
Same as Hd116
oA-20
Same as Hd118
at an option error (SLOT-2)
oA-21
Watch Dog Timer (SLOT-2)
Range Initial
oA-22
(unit) value
a communication error
Same as Hd130
(SLOT-2)
Same as Hd131
oA-23
Same as Hd132
selection at start up (SLOT-2)
Same as Hd133
oA-30
at an option error (SLOT-3)
Same as Hd134
oA-31
Same as Hd135
Watch Dog Timer (SLOT-3)
Same as Hd136
oA-32
a communication error
Same as Hd137
(SLOT-3)
oA-33
selection at start up (SLOT-3)
・In P1-CCL CC-Link communication option, there are no
dedicated parameters other than the above parameters. For
more information, contact to your supplier or local Hitachi
distributor or service station.
P1-FB Encoder Feedback Option setting
ob-01
Encoder constant setting
ob-02
sequence selection
ob-03
numerator
ob-04
denominator
・Above parameters set the main encoder input and the motor
gear ratio involved in the encoder feedback for the P1-FB.
4-48
For parameter configuration
Code/Name Range (unit)
00(Error)/
Operation selection
01((Ignore error
(keep running))
Communication
0.00 to 100.00(s)
00(Error)/
01(Trip after Deceleration
Action selection at
stop)/02(Ignore)/
03(Free run stop)/
04(Deceleration stop)
00(Disable)/
RUN command
01(Enable)
00(Error)/
Operation selection
01((Ignore error
(keep running))
Communication
0.00 to 100.00(s)
00(Error)/
01(Trip after Deceleration
Action selection at
stop)/
02(Ignore)/
03(Free run stop)/
04(Deceleration stop)
00(Disable)/
RUN command
01(Enable)
00(Error)/
Operation selection
01((Ignore error
(keep running))
Communication
0.00 to 100.00(s)
00(Error)/
01(Trip after Deceleration
Action selection at
stop)/02(Ignore)/
03(Free run stop)/
04(Deceleration stop)
00(Disable)/
RUN command
01(Enable)
Code/Name
32 to 65535(pls)
00(A Phase lead)/
Encoder phase
01(B Phase lead)
Motor gear ratio
1 to 10000
Motor gear ratio
1 to 10000
Initial value
00
1.00
01
00
00
1.00
01
00
00
1.00
01
00
Initial
Range (unit)
value
1024
0
1
1