All manuals and user guides at all-guides.com TABLE OF CONTENTS TABLE OF CONTENTS SAFETY INFORMATION IMPORTANT INFORMATION INTRODUCTION Overview ....................ix Features ....................ix Options....................x Using this Manual..................x Conventions ...................xi SETTING UP THE SCANNER GENERAL GUIDE .................. 1-1 Front View ................... 1-1 Rear View....................
Page 4
All manuals and user guides at all-guides.com TABLE OF CONTENTS INSTALLING THE DRIVERS............... 1-14 Installing the TWAIN Scanner Driver ..........1-14 Installing the ISIS Scanner Driver............. 1-14 USING THE SCANNER INTRODUCTION ................... 2-1 PLACING ORIGINALS ON THE SCANNER ......... 2-2 USING THE BOOK MODE ..............
Page 5
All manuals and user guides at all-guides.com TABLE OF CONTENTS A. SCANNER FEATURES SCANNER FUNCTIONALITY ..............A-1 Prescan ....................A-1 Scan ....................A-2 Scanning composition .................A-3 Binary Scanning-Threshold..............A-4 Dynamic threshold ................A-5 Halftone scanning ................A-6 Multi-value scanning ................A-7 Area extraction ..................A-8 Section area (multi-area settings) ............A-9 Auto photo/letter................A-10 Resolution ..................A-11 Brightness ..................A-12...
All manuals and user guides at all-guides.com SAFETY INFORMATION SAFETY INFORMATION When using your machine, the following safety precautions should always be followed. WARNING: Ignoring this warning could cause serious injury or even death. CAUTION: Ignoring this caution could cause injury or damage to property.
Page 7
All manuals and user guides at all-guides.com SAFETY INFORMATION $ WARNINGS: • Only connect the machine to the power source > described in the Important Information Section. • Avoid multi-wiring. • Do not damage , break or make any modifications to the power cord.
Page 8
All manuals and user guides at all-guides.com SAFETY INFORMATION $ CAUTIONS: • > Keep the machine away from humidity and dust. A fire or an electric shock might occur. • Do not place the machine on an unstable or tilted surface.
All manuals and user guides at all-guides.com SAFETY INFORMATION IMPORTANT INFORMATION IMPORTANT INFORMATION 1. Read all of these instructions and keep them for later reference. 2. Follow all warnings and instructions marked on the machine. 3. Unplug this machine from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Page 10
All manuals and user guides at all-guides.com SAFETY INFORMATION IMPORTANT INFORMATION 12. Except as specifically explained in the operator’s manual, do not attempt to service this device yourself. Opening or removing those covers that are marked “Do Not Remove” may expose you to dangerous, voltage points or to other risks.
All manuals and user guides at all-guides.com INTRODUCTION INTRODUCTION This manual contains detailed instructions on the operation and maintenance of your scanner. To obtain maximum versatility from your scanner, you should carefully read this manual and follow the instructions it provides. Make sure to read the “Safety Information”...
All manuals and user guides at all-guides.com INTRODUCTION Options The following are available to you as options that you can add to the basic components provided with your scanner: Image Processing Unit Operation Panel Kit Using this Manual This manual explains how to configure and use the scanner. This section provides short descriptions of the chapters that make up this manual, the conventions used throughout the manual, and various publications that may be of further use to you when using the scanner.
All manuals and user guides at all-guides.com INTRODUCTION Conventions The following conventions are used throughout this manual: Square brackets - the names of the hard keys, soft keys and buttons on the scanner and on your host computer are enclosed in square brackets. For example, the [Start] button.
Page 14
All manuals and user guides at all-guides.com INTRODUCTION General Information Some of the illustrations of the scanner in this manual may differ slightly from the actual appearance of your scanner. Some of the options described in this manual may not be available in your country.
All manuals and user guides at all-guides.com SETTING UP THE SCANNER SETTING UP THE SCANNER GENERAL GUIDE The following illustrations show the names of the various components that make up the scanner. Front View Document Feeder Closed Document table Output table Document stopper Scanner indicators...
All manuals and user guides at all-guides.com SETTING UP THE SCANNER Rear View SCSI Power cord socket RS-232C connector Rotary switch connectors DIP switches Service switch CAUTION: Do not touch the service switch. This switch is provided for use by service personnel only. Scanner Indicators Power on Machine busy...
All manuals and user guides at all-guides.com SETTING UP THE SCANNER CHECKING THE PARTS Make sure that you have all the parts shown below in your packing box. Parts list Name Q’ty Name Q’ty Scanner Power cord Terminator driver soft & manual (ISIS) 1set Operator’s manual Scanner...
All manuals and user guides at all-guides.com SETTING UP THE SCANNER SCANNER LOCATION Before actually setting up the scanner, take a few minutes to consider where you plan to use it. Remember the following points when doing this. Set up the scanner in an easily accessible area with temperatures between 50 and 90 degrees Fahrenheit (10 to 32 degrees...
All manuals and user guides at all-guides.com SETTING UP THE SCANNER CONNECTING TO THE HOST Use the following procedure to connect the scanner to a host computer using a SCSI cable. Note the following important points when making SCSI cable connections. Turn all devices being connected before making any connections.
Page 20
All manuals and user guides at all-guides.com SETTING UP THE SCANNER Plug one end of the shielded high density 50-pin SCSI II cable (ANSI-compliant*1) into the SCSI II port located on the back of the scanner. If you do not plan to connect anything to the other port, cap it with a terminator*2.
Page 21
All manuals and user guides at all-guides.com SETTING UP THE SCANNER *2 Terminators Generally you need to have two terminators at each end of a SCSI chain. If you connect this scanner at the end of a SCSI chain, you should cap the scanner’s unused SCSI port with a terminator.
All manuals and user guides at all-guides.com SETTING UP THE SCANNER SETTING THE SCSI ID Each device in a SCSI chain must have its own unique ID. Use the procedure below to set the scanner’s SCSI ID. Note the following important points when setting the scanner’s SCSI ID. No two devices in the SCSI chain can have the same SCSI ID.
All manuals and user guides at all-guides.com SETTING UP THE SCANNER USING TWO SCANNERS IN THE SAME SCSI CHAIN Two of these scanners can be included in the same SCSI chain. In such a case, you must make sure to correctly make certain settings in order to avoid conflicts in the chain.
All manuals and user guides at all-guides.com SETTING UP THE SCANNER CONNECTING THE POWER CORD Use only the power cord that comes with the scanner to connect it to a power source. Note the following important points when connecting the power cord. Use only the power cord supplied with the scanner.
All manuals and user guides at all-guides.com SETTING UP THE SCANNER TURNING ON THE SCANNER Use the procedure below to turn on scanner power. To turn on the scanner power Check to make sure that the DIP switches on the back of the scanner are set correctly.
All manuals and user guides at all-guides.com SETTING UP THE SCANNER DIP SWITCH SETTINGS DIP switches on the back of the scanner can be used to control certain scanner features and functions. The following describes the DIP switch settings that can be made by you.
All manuals and user guides at all-guides.com SETTING UP THE SCANNER To change DIP switch settings Turn off the scanner and make the DIP switch settings described above. Turn the scanner back on. 1-13...
All manuals and user guides at all-guides.com SETTING UP THE SCANNER INSTALLING THE DRIVERS You must intall the scanner driver software on the host computer before you can use the scanner. Installing the TWAIN Scanner Driver Follow these steps to install the TWAIN scanner driver on your Windows 3.1, Windows 95, and Windows NT system: Insert the “TWAIN Scanner Driver for Windows”...
All manuals and user guides at all-guides.com USING THE SCANNER USING THE SCANNER INTRODUCTION This chapter describes what you need to know to how to use the scanner. Note that only operation of the scanner’s hardware is covered here. For details about using the scanner’s software driver you need to consult the separate Scanner Driver Manual for ISIS and the Driver Online-help for TWAIN.
All manuals and user guides at all-guides.com USING THE SCANNER PLACING ORIGINALS ON THE SCANNER You can place your originals on the scanner for scanning in one of two ways: you can place them manually directly onto the glass one at a time (Book Mode), or you can use the document feeder to feed the originals automatically (Document Feeder Mode).
All manuals and user guides at all-guides.com USING THE SCANNER USING THE BOOK MODE With the Book Mode, you place the object you want to scan directly onto the glass. You must use this mode when scanning pages in a book, magazine, or other bound document.
Page 32
All manuals and user guides at all-guides.com USING THE SCANNER Slowly close the document feeder. Execute the scan operation from the host computer. CAUTION: Take care to avoid strong pressure on or impact to the scanner’s glass while the document feeder is open, otherwise glass is broken and this may cause injury.
All manuals and user guides at all-guides.com USING THE SCANNER USING THE DOCUMENT FEEDER MODE The Document Feeder Mode lets you automatically feed single-sheet originals from the document feeder for high-speed scanning. The following defines the type of original that can be scanned using the Document Feeder Mode.
All manuals and user guides at all-guides.com USING THE SCANNER To use the document feeder Fan the stack of originals and even up its four sides. Raise the document stopper. Squeezing the guide lock on the left side of the guide, adjust the document guides so they match the wide of the original.
Page 35
All manuals and user guides at all-guides.com USING THE SCANNER Note: Make sure the top of the stack of originals is not above the top lines marked on the guides. Place the stack of originals onto the document feeder, and slide them into the feeder until the indicator lights.
All manuals and user guides at all-guides.com MAINTENANCE MAINTENANCE OVERVIEW This chapter tells you everything you need to know about maintenance of your scanner and procedures to take to solve scanner problems. This information helps keep your scanner in good working condition and helps you correct any problems that might occur.
All manuals and user guides at all-guides.com MAINTENANCE CLEANING THE SCANNER This section describes the cleaning requirements of your scanner. Remember that keeping scanner components clean is the secret to both good scanning results and long scanner life. Contact Glass, Slit Glass, White Sheet, White Bar Dirty glasses or white sheet and bar adversely affects the quality of your scanned images.
All manuals and user guides at all-guides.com MAINTENANCE Rollers and Belt Feed errors such as jams or multiple feeding indicate that the scanner’s rollers or belt may need cleaning. Open the document feeder cover to inspect the rollers and belt for dirt. If they are dirty, clean them with a damp cloth. Open the document feeder cover.
Page 39
All manuals and user guides at all-guides.com MAINTENANCE After closing the feed roller unit, use a damp soft cloth to clean the two rollers inside the document feeder cover. If feed errors continue to occur after you clean the rollers, it may mean that it’s time to replace the roller set (see the next section).
All manuals and user guides at all-guides.com MAINTENANCE REPLACING THE ROLLER SET Your scanner requires periodic cleaning of the roller set in order to keep originals feeding properly. If feed problems continue to occur even after you clean the roller set, it means that you must replace the roller set with a new one. Contact your dealer for information about purchasing a roller assembly.
Page 41
All manuals and user guides at all-guides.com MAINTENANCE Pull out the black plastic cover next to the large white roller, and then remove the white roller. Note: Take care that you do not damage the nearby mylar guide when removing Roller A.
Page 42
All manuals and user guides at all-guides.com MAINTENANCE Replace the black plastic cover. Install the new feed roller unit into the scanner as shown in the illustration. Double check to make sure that the pins on the end of the shaft that is towards the back of the scanner seat properly into the holes that are provided.
All manuals and user guides at all-guides.com TROUBLESHOOTING TROUBLESHOOTING OVERVIEW This chapter provides information on problems that may occur while using the scanner, as well as the actions you can take to solve the problems. Operational errors are indicated by indicators located on the front of the scanner, above the power switch.
All manuals and user guides at all-guides.com TROUBLESHOOTING Document Feeder Raised Indicator Color Green Green Green Status This error indicates that the document feeder is raised. Lower the document feeder cover, making sure it goes all the way down. Paper Jam Indicator Color Green...
Page 45
All manuals and user guides at all-guides.com TROUBLESHOOTING Inspect the original for tears or curling. If it is in good condition, return it to the starting position on the document feeder and restart the scan job. If the original is wrinkled, smooth it out and scan using the Book Mode.
All manuals and user guides at all-guides.com TROUBLESHOOTING Paper Misfeed Indicator Color Green Green Green Status This error indicates that the document feeder could not feed the originals for some reason. Open the document feeder cover and carefully remove the original as shown in the illustration.
All manuals and user guides at all-guides.com TROUBLESHOOTING Return the green release lever to its original position. Inspect the original for tears or curling. If it is in good condition, return it to the starting position on the document feeder and restart the scan job.
Page 48
All manuals and user guides at all-guides.com TROUBLESHOOTING 2WKHU3UREOHPV The following table shows other possible problems that are not indicated by the indicators, along with the actions you should take to correct them. Condition Action Scanner is not Make sure that the power switch is on. turned on.
All manuals and user guides at all-guides.com SCANNER SPECIFICATIONS SCANNER SPECIFICATIONS SPECIFICATIONS This section contains the electrical and hardware specifications for your scanner as well as information on the paper feed capabilities provided by the Automatic Document Feeder (ADF). Electrical and Hardware Specifications Note: All specifications are subject to change without notice.
All manuals and user guides at all-guides.com SCANNER SPECIFICATIONS Environmental Specifications Temperature: 10 to 32 degrees Celsius Humidity: 20 to 80 percent Air circulation: 30 cubic meters, per person, per hour Clearance: 600 mm (24”) above 30 mm (1”) left and right sides 50 mm (2”) rear...
Page 51
All manuals and user guides at all-guides.com SCANNER SPECIFICATIONS ,17(5)$&(6 This section provides information on the shielded high density 50-pin SCSI II cable you use to connect your scanner to your host computer, on the SCSI II Terminator plug you use on your machine, and on the RS-232C interface. It is your responsibility to make sure that you have a SCSI II port available on the host computer and to provide the SCSI II cable.
All manuals and user guides at all-guides.com SCANNER SPECIFICATIONS SCSI II Interface The SCSI II connection is a standard SCSI II interface and requires a shielded high density 50-pin SCSI II bus and tag cable with an A Connector and a SCSI II port available on the host computer.
Page 53
All manuals and user guides at all-guides.com SCANNER SPECIFICATIONS Code Signal DB<2> Data DB<3> Data DB<4> Data DB<5> Data DB<6> Data DB<7> Data DB<P> Data Signal Ground Signal Ground RESERVED Reserved TERMPWR* Term Power RESERVED Reserved Signal Ground -ATN Attention Signal Ground -BSY Busy...
All manuals and user guides at all-guides.com SCANNER SPECIFICATIONS RS-232C Interface This interface is provided for connection of the optional Operation Panel. It requires a standard RS-232C cross cable (3 meters maximum length) for connection. The scanner side of the cable should have a 25-pin male connector, while the other end of the cable should have a connector that matches the needs of your host computer.
All manuals and user guides at all-guides.com SCANNER SPECIFICATIONS OPTIONS This section describes the options that are available for this scanner. Options include an Image Processing Unit (IPU) and an Operation Panel. ,PDJH3URFHVVLQJ8QLW The optional Image Processing Unit (IPU) adds the following functionality: Dynamic threshold - the scanned image is automatically converted to line art using the appropriate threshold.
All manuals and user guides at all-guides.com SCANNER FEATURES A. SCANNER FEATURES SCANNER FUNCTIONALITY This appendix contains descriptions and illustrations of the functions and features provided by your scanner, as well as illustrations of how your scanned images will output based on various specifications. Note: The scanner is controlled by the driver software you are using.
Page 57
All manuals and user guides at all-guides.com SCANNER FEATURES 6FDQ Function Scanning a selected area of an image using the settings you specify. Usage Enter the settings you want to use, for example, the scan area, scanning composition, resolution, and so forth. Use Scan to scan the image using these parameters.
All manuals and user guides at all-guides.com SCANNER FEATURES Scanning composition Function You can scan using one of three compositions: binary, halftone, or multi-value. Binary scanning records only black and white from the original. Halftone scanning records gray shades from the original using a pattern of black and white dots.
All manuals and user guides at all-guides.com SCANNER FEATURES Binary Scanning - Threshold Function Binary scanning converts every pixel included in the image to either black or white. When the image contains a gray area, the threshold value determines whether the scanner records the area as black or white.
All manuals and user guides at all-guides.com SCANNER FEATURES Dynamic threshold The scanned image is converted to binary using an appropriate threshold. The threshold is determined by the scanner using an optional image processing unit. Dynamic threshold Note:Dynamic threshold is available only when the optional Image Processing Unit is installed.
All manuals and user guides at all-guides.com SCANNER FEATURES Halftone scanning Function Creates the illusion of gray scales by simulating shades of gray from patterns of black and white dots. Usage Use halftone scanning when you are scanning an image that has gray shadings (for example, a photograph) when you want to print or display the image on a monochrome device, such as a laser printer.
All manuals and user guides at all-guides.com SCANNER FEATURES Multi-value scanning Function Multi-value scanning can record 4, 6, or 8 bits of information for each dot on the image. The 4-bit multi-value data represents 16 different shades of gray, the 6-bit data represents 64 shades of gray, and the 8-bit data represent 256 different shades of gray.
All manuals and user guides at all-guides.com SCANNER FEATURES Area extraction Function Extracts a rectangular area from the whole scannable area. Usage Use area extraction when you want to extract a portion of an image. For example, when you want to extract a photograph from a page, define a rectangle over the photograph, as shown below.
All manuals and user guides at all-guides.com SCANNER FEATURES Section area (multi-area settings) Function Within the scan area, you can set separate rectangular areas and define separate scanning modes, such as binary scanning, halftone scanning, or binary filters, for each area. You can specify up to six areas for one scan.
All manuals and user guides at all-guides.com SCANNER FEATURES Auto photo/letter Function The auto photo/letter mode detects photograph (halftone) areas and letter (binary) areas of the original so that the binary areas are scanned in the binary mode, and the halftone areas are scanned in the halftone mode.
All manuals and user guides at all-guides.com SCANNER FEATURES Resolution Function Sets vertical and horizontal resolution independently at 60, 75, and 100 to 800 dots per inch (dpi). The higher the resolution, the finer the detail. However, a high resolution image requires much more memory and processing time than a low resolution image.
All manuals and user guides at all-guides.com SCANNER FEATURES Brightness Function Adjusts the brightness value between 1 and 255. A high brightness setting results in a lighter overall image, while a low brightness setting results in a darker overall image. Usage When scanning a dark image, the darker area may display as deep black, even though it has gray scales.
All manuals and user guides at all-guides.com SCANNER FEATURES Gamma correction Function Selects the following gamma correction settings: Normal - emphasizes contrast slightly to improve a scanned image. Sharp - emphasizes contrast to sharpen an image. Smooth - weakens contrast to soften an image. Linear - outputs an image as scanned.
All manuals and user guides at all-guides.com SCANNER FEATURES Binary filter Function You can use the following binary filters for binary scanning: Noise elimination - eliminates independent black or white dots. Smoothing - flattens uneven dots. Thickening black lines - thickens thin lines. Edge extraction - extracts outlines of the image.
All manuals and user guides at all-guides.com SCANNER FEATURES Parameter download Function Downloads a gamma curve and a dither pattern to the scanner. You can modify the scanned image with your gamma curve and convert it to binary using your dither pattern. Refer to your software manual for information on how to download these parameters to the scanner.
All manuals and user guides at all-guides.com GLOSSARY GLOSSARY ACRONYMS This section contains a list of the acronyms you may use while working with the scanner and the scanner documentation. Automatic Document Feeder dots per inch Input/Output Light Emitting Diode Megabyte Personal Computer pages per minute...
All manuals and user guides at all-guides.com GLOSSARY TERMS This section contains a list of the terms you may use while working with the scanner and the scanner documentation. application Software program, or programs used to process information. asynchronous Data communication transmissions that are controlled by start and stop characters, causing the time intervals between the transmission of data blocks to be unequal in length.
Page 73
All manuals and user guides at all-guides.com GLOSSARY Dots per inch. The number of dots that scan in an inch. These are used to form a character or graphic on the scanned page. drivers Software used to provide scanner characteristics. image area Area of the scanned page that can contain graphics or text.
Page 74
All manuals and user guides at all-guides.com GLOSSARY raster Graphic created using a pattern of dots. graphics Raster image Processor board (RIP) that builds a raster image that is processor passed to the scanner. rasterization Transformation of an image onto a page using bitmap dots. resolution Number of dots per inch (dpi) or spots per inch (spi).
Page 75
All manuals and user guides at all-guides.com Part No. G4058600 Printed in Japan...