Sony LMD-A240 Operating Instructions Manual page 18

Submenu Setting
[Manual Adjustment] If you set the [Color Temp] to the
[User1] or [User2] setting, the item
displayed is changed from black to
white, which means you can adjust the
color temperature.
The set values are memorized.


Note
If the [Password Lock] has been turned
[On], the [User1] value is protected by a
password. To change the values, enter
the password.
[Color Space] Selects the color space from among
[ITU-R BT.709], [EBU], [SMPTE-C],
[Native], [S-Gamut/S-Gamut3], [S-
Gamut3.Cine], [DCI-P3], [ITU-R
BT.2020], [Adobe RGB]
[Native] sets the color space to the
original color reproduction of the panel.
1) Adobe is a trademark of Adobe
Notes




18
Adjustment Using the Menus
[Adjust Gain/Bias]:
[R Gain]: Adjusts the color

balance (gain) of R (red).
[G Gain]: Adjusts the color

balance (gain) of G (green).
[B Gain]: Adjusts the color

balance (gain) of B (blue).
[R Bias]: Adjusts the color

balance (bias) of R (red).
[G Bias]: Adjusts the color

balance (bias) of G (green).
[B Bias]: Adjusts the color

balance (bias) of B (blue).
[Copy From]: If you select [D50],
[D65], [D93], [User1] or
[User2], the white balance data
for the selected color
temperature will be copied to the
[User1] or [User2] setting.
1)
, [sRGB].
Systems Incorporated.
The color space which the unit can
reproduce is limited.
When the HDMI signal is input, the
color space may not match even if
[ITU-R BT.2020] is selected.
Use [S-Gamut/S-Gamut3] in
combination with Gamma [S-Log3]
or [S-Log2].
Use [S-Gamut3.Cine] in
combination with Gamma [S-Log3].
Submenu Setting
[Gamma] Select the appropriate gamma mode
from among [2.2], [2.4], [2.6],
[2.4(HDR)], [S-Log3], [S-Log2],
[SMPTE ST 2084], [ITU-R
BT.2100(HLG)], or [S-Log3(Live
HDR)].
Notes
When the gamma mode is changed,

the menu screen color may change.
When the monitor is connected with

an HDMI cable, signals of the
gamma [2.4(HDR)], [S-Log3], [S-
Log2], [SMPTE ST 2084], [ITU-R
BT.2100(HLG)], and [S-Log3(Live
HDR)] may not be input depending
on the specifications of the monitor
and output devices.
System Gamma 1.2 is applied for

[ITU-R BT.2100(HLG)]. The system
gamma cannot be changed.
When the contrast is set to 86, [ITU-

R BT.2100(HLG)] shifts to the
gamma setting for BVM-HX310,
BVM-X300 (LMD-A180, LMD-
A220 (Serial No.7000001 to
7100000, 7200001 to 7300000),
LMD-A240). Brightness higher than
the maximum of the panel is clipped.
When the contrast is set to 92, [ITU-

R BT.2100(HLG)] shifts to the
gamma setting for BVM-HX310,
BVM-X300 (LMD-A220 (Serial No.
7100001 to 7200000, from 7300001
onwards)). Brightness higher than
the maximum of the panel is clipped.
The brightness adjustment of [ITU-

R BT.2100(HLG)] supports the ITU-
R BT.2100-2 standard.
The brightness adjustment of

[SMPTE ST 2084] supports the ITU-
R BT.814-4 standard.
The brightness-adjustment

specifications of [S-Log3], [S-Log2],
and [S-Log3(Live HDR)] are the
same as the specification of [SMPTE
ST 2084].
The Monitor Auto White

Adjustment software (for measuring
and automatically adjusting the
color temperature and brightness of
a monitor) is enabled only when
[2.2] or [2.4] is selected as the
gamma mode.
About S-Log3(Live HDR)
"S-Log3(Live HDR)" displays the S-Log3 input signal
adding the system gamma in the S-Log3 Live HDR
1)
workflow which Sony advocates.
This system gamma is set so that the compatibility with
the monitoring of the conventional (SDR) environment
is valued and you can perform suitable picture
expression without discomfort when adjusting the
picture of the HDR camera.