Crestron TSW-732 Manual

DO GUIDE
TSW-732
7" Room Scheduling Touch Screen
DO Change the Button Inserts or Button Covers
The Crestron TSW-732 Touch Screen ships with 10 "hard key" push buttons for quick access to
®
commonly used functions. Optional, custom engravable button covers are available (TSW-730-BTNO
and custom engraving sold separately). For a clean appearance, either column of buttons may be
removed and covered using the included no-button covers.
To change the inserts or covers, use the following procedure:
1. Insert a small flat head screwdriver into the appropriate hole on the bottom of the TSW-732 to
release its cover.
Insert a screwdriver to release the covers.
2. Gently remove the cover from the TSW-732.
3. If removing the button insert after removing the button cover, use a small flat head screwdriver
to press the tabs, and then gently lift the button insert from the TSW-732. Refer to the following
illustration for the tab locations on the button insert.
Touch Screen with Button Inserts
Use a screwdriver
to release
the button insert.
4. Carefully position the new cover over the front of the touch screen and press it into place.
Touch Screen with No-Button Covers
DO Check the Box
QUANTITY
1
1
1
1
DO Install the Touch Screen
2
The TSW-732 can be mounted into a standard
2
electrical box or onto a flat surface. A tabletop
2
enclosure and swivel mount (TSW-730-TTK and
SMK-4SM/730, both sold separately) are also 2
available.
2
Mounting into a U.S. Electrical Box
4
1
To mount the TSW-732 into a U.S. electrical box,
use the following procedure:
1. Insert a small flat head screwdriver into the
hole shown in the following illustration and
gently separate the back panel from the touch screen.
Insert a screwdriver to separate the back panel.
2. Use the four included 06-32 x 1 1/2" screws to attach the back panel to the electrical box.
U.S. Electrical Box
Screws (4) 06-32 x 1 1/2"
TSW-732
3. Make connections to the TSW-732 using Crestron power supplies for Crestron equipment.
LAN PoE:
Occupancy Sensor Input:
10BASE-T / 100BASE-TX
From Room Occupancy Sensor
Ethernet to LAN
PRODUCT
Plastic Cover, No-Button, Left 1
Plastic Cover, No-Button, Left 2
Plastic Cover, No-Button, Right
1
Plastic Cover, No-Button, Right
2
Screws, 4B x 3/4", Phillips
Screws, 04-40 x 1/4", Phillips 1
Screws, 04-40 x 1/4", Phillips
2
Screws, 04-40 x 1/4", Torx
1
Screws, 04-40 x 1/4", Torx 2
Screws, 06-32 x 1 1/2", Phillips
Bit, Torx
1. This part ships with the TSW-732-B-S.
2. This part ships with the TSW-732-W-S.
4. Carefully position the front of the touch screen over the back panel and gently snap it into place.
5. Use two of the included 04-40 x 1/4" screws to secure the TSW-732. For standard applications,
use the Phillips screws. For secure applications, use the security type Torx screws along with
the included Torx screwdriver bit.
Screws (2) 04-40 x 1/4" Phillips
or
Screws (2) 04-40 x 1/4" Torx
Mounting into a U.K. Electrical Box
To mount the TSW-732 into a U.K. electrical box, use the following procedure:
1. Insert a small flat head screwdriver into the hole shown in the following illustration and gently
separate the back panel from the touch screen.
Insert a screwdriver to separate the back panel.
2. Use the two included 4B x 3/4" screws to attach the back panel to the electrical box.
U.K. Electrical Box
COLOR PART NUMBER
Black 2033452
White 2033451
Black 2033450
White 2033449
2019088
Black 2007152
Zinc 2007160
Black 2025311
Stainless Steel 2025312
2031703
2025915
Screws (2) 4B, 3/4"
TSW-732