System Parameters - Roland FP-4 Midi Implementation Manual

■Individual Parameters
Individual Parameter Transmission transmits data (or requests data) for one parameter as one exclusive message (one packet of "F0 ..... F7").
In Individual Parameter Transmission, you must use the Address and Size listed in the following "Parameter Address Map." Addresses marked at "#" cannot be used as starting addresses.
●System Parameters
Parameters related to the system of the device are called System Parameters.
Address (H) Size (H)
40 00 00 00 00 04
40 00 01#
40 00 02#
40 00 03#
* Refer to section 4. Supplementary material, "About tuning" (p. 15).
40 00 04 00 00 01
40 00 05 00 00 01
40 00 06 00 00 01
40 00 7F 00 00 01
* Refer to "System exclusive messages related to mode settings" (p. 4).
40 01 10 00 00 10
40 01 11#
40 01 12#
40 01 13#
40 01 14#
40 01 15#
40 01 16#
40 01 17#
40 01 18#
40 01 19#
40 01 1A#
40 01 :#
40 01 1F#
* The sum total of voices in the voice reserve function must be equal to or less than the number of the maximum polyphony. The maximum polyphony of this instrument is 128. For
compatibility with other GS models, it is recommended that the maximum polyphony be equal or less than 24.
40 01 30 00 00 01
40 01 31 00 00 01
40 01 32 00 00 01
40 01 33 00 00 01
40 01 34 00 00 01
40 01 35 00 00 01
* REVERB MACRO is a macro parameter that allows global setting of reverb parameters. When you select the reverb type with REVERB MACRO, each reverb parameter will be set to the most
suitable value.
* REVERB CHARACTER is a parameter that changes the reverb algorithm. The value of REVERB CHARACTER corresponds to the REVERB MACRO of the same number.
40 01 38 00 00 01
40 01 39 00 00 01
40 01 3A 00 00 01
40 01 3B 00 00 01
40 01 3C 00 00 01
40 01 3D 00 00 01
40 01 3E 00 00 01
40 01 3F 00 00 01
* CHORUS MACRO is a macro parameter that allows global setting of chorus parameters. When you use CHORUS MACRO to select the chorus type, each chorus parameter will be set to the
most suitable value.
Data (H) Parameter
0018-07E8 MASTER TUNE
00-7F MASTER VOLUME
(= F0 7F 7F 04 01 00 vv F7)
28-58 MASTER KEY-SHIFT
01-7F MASTER PAN
00 MODE SET
00-40 VOICE RESERVE
00-07 REVERB MACRO
00-07 REVERB CHARACTER
00-07 REVERB PRE-LPF
00-7F REVERB LEVEL
00-7F REVERB TIME
00-7F REVERB DELAY FEEDBACK
00-07 CHORUS MACRO
00-07 CHORUS PRE-LPF
00-7F CHORUS LEVEL
00-7F CHORUS FEEDBACK
00-7F CHORUS DELAY
00-7F CHORUS RATE
00-7F CHORUS DEPTH
00-7F CHORUS SEND LEVEL TO REVERB
Description
-100.0 - +100.0 [cent]
Use nibblized data.
0-127
-24 - +24 [semitones]
-63 (LEFT) - +63 (RIGHT)
00 = GS Reset,
127 = Exit GS mode
(Rx. only)
Part 10 (Drum Part)
Part 1
Part 2
Part 3
Part 4
Part 5
Part 6
Part 7
Part 8
Part 9
Part 11
:
Part 16
00: Room 1
01: Room 2
02: Room 3
03: Hall 1
04: Hall 2
05: Plate
06: Delay
07: Panning Delay
0-7
0-7
0-127
0-127
0-127
00: Chorus 1
01: Chorus 2
02: Chorus 3
03: Chorus 4
04: Feedback Chorus
05: Flanger
06: Short Delay
07: Short Delay (FB)
0-7
0-12
0-127
0-127
0-127
0-127
0-127
MIDI Implementation
Default Value (H) Description
00 04 00 00 0 [cent]
7F 127
40 0 [semitones]
40 0 (CENTER)
02 2
06 6
02 2
02 2
02 2
02 2
02 2
02 2
02 2
02 2
00 0
00 0
04 Hall 2
04 4
00 0
40 64
40 64
00 0
02 Chorus 3
00 0
40 64
08 8
50 80
03 3
13 19
00 0
9