Parameter Address Map (Model Id = 42H); Address Block Map; Individual Parameters; System Parameters - Roland F-120R Implementation Manual

MIDI Implementation

3. Parameter Address Map (Model ID = 42H)

This map indicates address, size, Data (range), Parameter, Description, and Default Value of parameters which can be transferred using and "Data set 1 (DT1). "
All the numbers of address, size, Data, and Default Value are indicated in 7-bit Hexadecimal-form.

■ Address Block Map

An outlined address map of the Exclusive Communication is as follows;
+------------+------------------------------------+
| Address (H)| Block
+------------+------------------------------------+
| 40 00 00 |
|

| SYSTEM PARAMETERS

| 40 01 3F |
+------------+------------------------------------+
+------------+------------------------------------+
| 40 1x 00 |
| | PART PARAMETERS (x = 0-F)
| 40 2x 5A |
+------------+------------------------------------+
+------------+------------------------------------+
| 48 00 00 |
| | SYSTEM PARAMETERS
| |
+------------+------------------------------------+
| 48 01 10 |
| | PART PARAMETERS
| 48 1D 0F |
+------------+------------------------------------+
There are two ways in which GS data is transmitted: Individual Parameter Transmission in which individual parameters are transmitted one by one, and Bulk Dump Transmission in
which a large amount of data is transmitted at once.

■ Individual Parameters

Individual Parameter Transmission transmits data (or requests data) for one parameter as one exclusive message (one packet of "F0 ..... F7").
In Individual Parameter Transmission, you must use the Address and Size listed in the following "Parameter Address Map. " Addresses marked at "#" cannot be used as starting
addresses.
●System Parameters
Parameters related to the system of the device are called System Parameters.
Address (H) Size (H)
40 00 00 00 00 04
40 00 01#
40 00 02#
40 00 03#
*Refer to section 4. Supplementary material, "About Tuning. "
40 00 04 00 00 01
40 00 05 00 00 01
40 00 06 00 00 01
40 00 7F 00 00 01
* Refer to "System exclusive messages related to mode settings".
40 01 10 00 00 10
40 01 11#
40 01 12#
40 01 13#
40 01 14#
40 01 15#
40 01 16#
40 01 17#
40 01 18#
40 01 19#
40 01 1A#
40 01 :#
40 01 1F#
* The sum total of voices in the voice reserve function must be equal to or less than the number of the maximum polyphony. The maximum polyphony of this instrument is 128.
For compatibility with other GS models, it is recommended that the maximum polyphony be equal or less than 24.
40 01 30 00 00 01
10
|
|
| Individual
|
|
| Individual
|
|
| Bulk
|
|
| Bulk
|
Data (H) Parameter
0018-07E8 MASTER TUNE
00-7F MASTER VOLUME
(= F0 7F 7F 04 01 00 vv F7)
28-58 MASTER KEY-SHIFT
01-7F MASTER PAN
00 MODE SET
00-40 VOICE RESERVE
00-07 REVERB MACRO
Description Default Value (H)
-100.0 - +100.0 [cent] 00 04 00 00
Use nibblized data.
0-127 7F
-24 - +24 [semitones] 40
-63 (LEFT) - +63 (RIGHT) 40
00 = GS Reset,
127 = Exit GS mode
(Rx. only)
Part 10 02
Part 1 06
Part 2 02
Part 3 02
Part 4 02
Part 5 02
Part 6 02
Part 7 02
Part 8 02
Part 9 02
Part 11 00
: :
Part 16 00
00: Room 1 04
01: Room 2
Description
0 [cent]
127
0 [semitones]
0 (CENTER)
2
6
2
2
2
2
2
2
2
2
0
:
0
Hall 2