Table of Contents
Advertisement
1-4
A1
Explanation of Signal Words and Symbols
MERCHANDISERS SHIPPED
Signal words and safety symbols that are used in a product's collateral materials or on the product may
be defined in collateral materials if space is available.
WITH END INSTALLED
A1.1
Safety Alert Symbol
The meaning of the safety alert symbol may be provided in collateral materials. The following artwork may
If the merchandiser was shipped with the end
be used for this purpose.
installed, two long bolts were used to hold the
shipping brace to the end . If the shipping bolts
are reinserted after removing the brace, they
will extend into the product area . T
sure To replace These bolTs wiTh The shorTer
. NSF requires any bolt or screw
bolTs provided
in the product area be capped or cut off if it
A1.2
Signal Words
has more than three exposed threads .
The meaning of the different signal words as defined by the ANSI Z535.6 and ANSI Z535.4 standards
may be explained in collateral materials. The following artwork may be used for this purpose.
Be careful not to damage the factory
installed end while moving the
merchandiser.
»
Do not remove shipping braces
until the merchandisers are
positioned for installation.
END SHIPPING BRACES
Move the merchandiser as close as possible to
A1.3
Other Highlighting Conventions
its permanent location, then remove all packaging .
The meaning of any other highlighting conventions used to differentiate safety messages (e.g., text
Check for damage before discarding packaging .
manipulations, indention, etc.) may be explained in collateral materials.
Remove all separately packed accessories such
A1.4
Safety Symbols
as kits and shelves .
The meaning of any safety symbols used on safety labels or collateral materials may be explained in
collateral materials.
Do not remove end braces until joining begins.
Recycle wooden braces and hardware .
SHIPPING RIDER
Some merchandisers are shipped on a rider to
protect the factory installed front legs, and to
make positioning the merchandiser easier . To
remove the rider, remove bolts attaching rider to
each leg .
P/N 3032067_E
Safety Signs and Labels
(Informative)
This is the safety alert symbol. It is used to alert you
to potential physical injury hazards. Obey all safety
herefore
messages that follow this symbol to avoid possible
injury or death.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
physical injury.
Safety instructions (or equivalent) signs indicate specific
safety-related instructions or procedures.
© 2017 National Electrical Manufacturers Association
Licensee=Hussmann Corp/8160899001, User=Trevett, Jason
Not for Resale, 02/16/2021 11:49:55 MST
U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
MERCHANDISER LEVELING
Merchandisers must be installed level to ensure
proper operation of the refrigeration system
and to ensure proper drainage of defrost water .
,
Pay close attention to case position during all
be
steps of setting, joining and leveling .
NOTE: B
egin lineup leveling from the highest
point of the store floor
Preparation
1 . Using store blueprints, measure off and
mark on floor the exact dimensions/locations
of the merchandiser footprint . A 1½ inch space
ANSI Z535.6-2011 (R2017)
is required behind each merchandiser to prevent
Page 18
condensation.
Providing Information About Safety Messages in Collatera
2 . Snap a chalk line for the front and rear
positions of the base pods .
3 . Mark the location of each joint from front
to back lines .
A1
Explanation of Signal Words and Symbols
Signal words and safety symbols that are used in a product's collateral mate
4 . u
be defined in collateral materials if space is available.
se supplied shims To level case
be inserted under the black, plastic base pods.
A1.1
Safety Alert Symbol
The meaning of the safety alert symbol may be provided in collateral materi
be used for this purpose.
A1.2
Signal Words
The meaning of the different signal words as defined by the ANSI Z535.6 an
may be explained in collateral materials. The following artwork may be used
Shim Case
»
Tipping Hazard! Case tipping may occur if cases are
not properly leveled and secured, or if cases are not
properly loaded.
.
Annex A
Safety Signs and Labels
(Informative)
. Shims are to
This is the safety alert symbol. It is
to potential physical injury hazard
messages that follow this symbol
injury or death.
DANGER indicates a hazardous
avoided, will result in death o
Shim
WARNING indicates a hazardou
avoided, could result in deat
Shim
CAUTION indicates a hazardous
avoided, could result in mino
NOTICE is used to address prac
physical injury.
Safety instructions (or equivalen
safety-related instructions or
Advertisement
Table of Contents
