Table of Contents
Advertisement
c. With voltmeter set to read 24 volts AC, attach the pos-
itive lead to the drive module outlet pin "A" (wire 1A) of
the four pin connector and the negative lead to the "B"
pin (wire 1B).
d. Turn ON unit, and watch the volt meter. After a short
delay, the reading should rise to approximately 12
volts.
e. Repeat for pins "C" and "D" (wires 2 A and 2 B).
f. If only one set of pins reads a voltage, check connec-
tions and retest.
g. If the retest reads out the same, the drive module or
controller is faulty.
h. If no voltage is present in any step, the output from the
controller to the drive module may be faulty, and will
require checking the connections and wires from the
controller to the drive module. Refer to step 6.18.4
i. To replace the drive module, disconnect all connec-
tors, unscrew from mounting, and replace with a
NEW drive module in reverse order.
6.18.4 Checking The Controller
a.
Turn the unit OFF.
b. Disconnect the six pin connector to the stepper drive
from the controller.
c. With the voltmeter set to read 50 volts DC, attach the
positive lead to outlet pin "A" of the six pin connector,
and the negative lead to pin "B" or TP-9 of the con-
troller.
d. Turn ON the unit for 40 seconds, and watch the volt-
meter. There should be approximately 24 to 32 VDC
shown on pin "A".
e. There should be zero volts on pin "B".
f. After a short delay, the reading should rise to approx-
imately 24 to 32 VDC on pin "E".
g. Pins "C" and "D" will have zero to 5 volts transistor
logic (TTL) signals present, however, this can only
be checked with the connector assembled as this is
an open collector type circuit.
By checking the outputs on "A," "B," and "E" it can be
verified that the controller is supplying power to the drive
module. To be thorough, and if it is desired, the signals
on pins "C" and "D" can be checked as follows:
1. Install a jumper assembly (Carrier part number
07--00408--00) to connect the drive module and con-
troller connectors as shown in Figure Figure 6-25.
2. Connect the positive lead of the voltmeter to test
connector socket "C" and negative lead to socket
"B," and run as before by resetting unit.
3. Repeat for sockets "D" and "B."
T-285
Controller
Connector (EC)
A
B
C
D
E
Test
Connector
Figure 6-25 Jumper Assembly
There should be approximately five volts DC on sockets
"C" and "D" (S1 and S2) when measured as above. If not
the connections or controller is faulty.
If any of these pins are not consistent, the connections
or controller is suspect. Check and replace as required.
6.18.5 Emergency Repair Procedures:
In the event that the SMV system has a failure and
replacement components are not readily available the
system can be by--passed by removing the valve piston.
to remove the piston, do the following:
a. Perform a low side pump down. Refer to paragraph
6.4.
b. Remove SMV powerhead by loosening the 2-1/8
inch diameter nut (see Figure 6-24) to relieve any
pressure and then , sliding the powerhead out.
c. Remove the piston by loosening the Allen screw and
removing the piston and screw.
d. Install the powerhead assembly (without the piston),
torque to 35 to 40 foot-lbs.
e. Open all valves.
f. Start the unit.
g. Adjust the suction service valve so that the approxi-
mate temperature OR current limit is maintained.
For perishable loads, it is recommended that the ad-
justment be made so that the available capacity is
slightly larger than the load, the unit will cycle OFF
and ON.
h. Once repair parts become available, repair as re-
quired.
6.19 AUTOTRANSFORMER
If the unit does not start, check the following:
a. Make sure the 460 vac (yellow) power cable is
plugged into the receptacle (item 3, Figure 4-1) and
locked in place.
b. Make sure that circuit breakers CB-1 and CB-2 are in
the "ON" position. If the circuit breakers do not hold in,
check voltage supply.
c. There is no internal protector for this transformer
design, therefore, no checking of the internal protec-
tor is required.
d. Using a voltmeter, and with the primary supply circuit
ON, check the primary (input) voltage (460 vac).
Next, check the secondary (output) voltage (230
vac). The transformer is defective if output voltage is
not available.
6-18
Drive Module
Connector (SD)
Jumper
A
B
C
D
E
Advertisement
Table of Contents
