Table of Contents
Advertisement
Tour Sequence (T-SEQ)
This table is used to program or edit a Tour Sequence.
There are 32 Tour Sequences available, each with 64 steps.
Each step has a camera number (CAM), an associated Pan/Tilt preset position (PRE), a dwell time (DWELL), and AUX 1 and
AUX 2 control assigned to it.
No monitor number is assignable in the Tour Sequence. The sequence will run on any monitor that the user can control.
A u t o
S t e p
C A M
P R E
D W E L L
A U X 1
A U X 2
S t e p
C A M
P R E
D W E L L
A U X 1
A U X 2
4
To program or edit a Tour Sequence, do the following:
Caution: Before programming or editing a Tour Sequence, the Alarm Mode must be in the Off mode first. Follow Alarm Mode
Select procedures on page 74.
1. Move the cursor to position 3 by moving the Joystick Controller. Enter the desired tour sequence number (1-32) by press-
ing the Numeric keys, and then pressing the CAM (SET) key to execute the selection.
2. Move the cursor to position 4 by moving the Joystick Controller. Press the Function F4 button to open the Pop Up Window.
Select Auto Skip On or Off by moving the Joystick Controller, and then press the CAM (SET) key to execute the selection.
3. Move the cursor to position 5 by moving the Joystick Controller. Enter the desired camera number (1-128) for each step by
pressing the Numeric keys.
4. Move the cursor to position 6 by moving the Joystick Controller. Enter the associated Pan/Tilt preset position number (if
applicable) by pressing the Numeric keys.
5. Move the cursor to position 7 by moving the Joystick Controller. Enter the desired Dwell Time (1-30) by pressing the
Numeric keys.
6. Move the cursor to position 8 or 9 by moving the Joystick Controller.
Press the Function F4 button to open the Pop Up Window.
Select AUX On or Off by moving the Joystick Controller, and then press the CAM (SET) key to execute the selection.
7. Press the function F1 button to select the next page or press the Function F2 button to select the previous page.
Repeat the above procedures until a tour sequence is completely assembled.
8. When satisfied with all of the above steps, press the MON (ESC) key to escape from the programming mode.
The cursor returns to position 3.
9. Repeat the above procedures to program the other Tour Sequences.
68
q
w
S e t
U p
P R O G .
T - S E Q
T o u r
S e q u e n c e 0 1
S k i p
O n
0 1
0 2
0 3
0 4
0 5
1 0
1 5
0 9
0 0
0 4
2 0
6 4
1 1
0 9
0 3
0 0
0 1
0 2
0 5
1 7
1 8
1 9
2 0
2 1
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
F 1 : N e x t
P a g e
F 2 : P r e
e
r
0 6
0 7
0 8
0 9
1 0
1 1
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
2 2
2 3
2 4
2 5
2 6
2 7
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
P a g e
F 3 : D E L
F 4 : P o p
P a g e
1 o f 2
1 2
1 3
1 4
1 5
1 6
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
2 8
2 9
3 0
3 1
3 2
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
. . O n
. . O f f
U p
t
y
u
i
o
Advertisement
Table of Contents
