Page 1 Wireless e Bluetooth User’s Guide NWA/WAC/WAX Series 802.11 a/b/g/n/ac/ax Access Point Default Login Details Version 6.00 Edition 2, 2/2020 Management IP http://DHCP-assigned IP Address http://192.168.1.2 User Name admin Password 1234 Copyright © 2020 Zyxel Communications Corporation...
Page 2 IMPORTANT! READ CAREFULLY BEFORE USE. KEEP THIS GUIDE FOR FUTURE REFERENCE. This is a User’s Guide for a series of products. Not all products support all firmware features. Screenshots and graphics in this book may differ slightly from your product due to differences in your product hardware, firmware, or your computer operating system.
Page 3: Document Conventions
Document Conventions Warnings and Notes These are how warnings and notes are shown in this guide. Warnings tell you about things that could harm you or your device. Note: Notes tell you other important information (for example, other things you may need to configure or helpful tips) or recommendations.
Page 4: Table Of Contents
Contents Overview Contents Overview Introduction ............................13 AP Management ..........................24 Hardware ............................... 33 Web Configurator ..........................53 Standalone Configuration ........................64 Standalone Configuration ........................65 Dashboard ............................67 Setup Wizard ............................73 Monitor ..............................79 Network ..............................94 Wireless ..............................105 Bluetooth .............................
Page 5: Table Of Contents
Table of Contents Table of Contents Document Conventions ........................3 Contents Overview ..........................4 Table of Contents ..........................5 Chapter 1 Introduction ............................13 1.1 Overview ............................13 1.2 Zyxel Device Roles .......................... 13 1.2.1 Root AP ........................... 14 1.2.2 Wireless Repeater ........................14 1.2.3 Radio Frequency (RF) Monitor .....................
Page 6 Table of Contents 3.3 Zyxel Device Models With Multiple LEDs ..................42 3.3.1 NWA1123-AC PRO ........................ 42 3.3.2 NWA1302-AC ......................... 44 3.3.3 WAC6502D-E, WAC6502D-S, and WAC6503D-S ..............46 3.3.4 WAC6103D-I ........................... 48 3.3.5 WAC5302D-S .......................... 50 Chapter 4 Web Configurator..........................53 4.1 Overview ............................
Page 7 Table of Contents Chapter 8 Monitor ..............................79 8.1 Overview ............................79 8.1.1 What You Can Do in this Chapter ..................79 8.2 What You Need to Know ....................... 79 8.3 Network Status ..........................80 8.3.1 Port Statistics Graph ......................81 8.4 Radio List ............................
Page 8 Table of Contents 11.2.1 Edit Advertising Settings ....................120 Chapter 12 User..............................122 12.1 Overview ............................. 122 12.1.1 What You Can Do in this Chapter ................... 122 12.1.2 What You Need To Know ....................122 12.2 User Summary ..........................123 12.2.1 Add/Edit User ........................123 12.3 Setting ............................
Page 9 Table of Contents Chapter 16 Certificates ............................154 16.1 Overview ............................. 154 16.1.1 What You Can Do in this Chapter ................... 154 16.1.2 What You Need to Know ....................154 16.1.3 Verifying a Certificate ...................... 156 16.2 My Certificates ..........................157 16.2.1 Add My Certificates ......................
Page 10 Table of Contents Chapter 18 Log and Report..........................193 18.1 Overview ............................. 193 18.1.1 What You Can Do In this Chapter .................. 193 18.2 Email Daily Report ........................193 18.3 Log Setting ........................... 195 18.3.1 Log Setting Screen ......................196 18.3.2 Edit System Log Settings ....................197 18.3.3 Edit Remote Server ......................
Page 11 Table of Contents 23.1 Overview ............................. 223 23.1.1 What You Need To Know ....................223 23.2 Reboot ............................223 Chapter 24 Shutdown ............................224 24.1 Overview ............................. 224 24.1.1 What You Need To Know ....................224 24.2 Shutdown ............................. 224 Part II: Local Configuration in Cloud Mode..........225 Chapter 25 Cloud Mode .............................226 25.1 Overview .............................
Page 12 Table of Contents 29.2 Power, Hardware Connections, and LED ................239 29.3 Zyxel Device Management, Access, and Login ..............240 29.4 Internet Access ........................... 244 29.5 WiFi Network ..........................245 29.6 Resetting the Zyxel Device ......................246 29.7 Getting More Troubleshooting Help ..................247 Appendix A Importing Certificates ....................
Page 13: Introduction
H A P T E R Introduction 1.1 Overview This User’s Guide covers the models listed in the following table. They can be managed in one of the following methods: remote management through Nebula Control Center (NCC) or an AP Controller (AC) such as the NXC, or local management in Standalone Mode.
Page 14: Root Ap
Chapter 1 Introduction • Wireless repeater - A wireless repeater wirelessly connects to a root AP and extends the network’s wireless range. The following figure shows a network setup that uses these different roles to create a secure Wireless Distribution System (WDS). The root AP (Y) is connected to a network with Internet access and has a wireless repeater (X) connected to it to expand the wireless network’s range.
Page 15: Radio Frequency (Rf) Monitor
Chapter 1 Introduction wireless clients and the wired LAN. Clients A and B access the AP and the wired network behind the AP through repeaters Z and Y. Figure 2 Repeater Application When the Zyxel Device is in Repeater mode, repeater security between the Zyxel Device and other repeater is independent of the security between the wireless clients and the AP or repeater.
Page 16 Chapter 1 Introduction Mode (RF Monitor mode), it will serve as a dedicated RF monitor and its AP clients are disconnected. The models that do not support MON Mode support Rogue AP Detection (see Section 10.3 on page 109). Rogue AP Detection allows the AP to scan all channels similar to MON Mode except that the Zyxel Device still works as an AP while it scans the environment for wireless signals.
Page 17: Sample Feature Applications
Chapter 1 Introduction To quarantine a rogue AP, go to CONFIGURATION > Wireless > Rogue AP, select the APs you want to quarantine, and click Containment. Make sure the Enable Rogue AP Containment check box is selected, and click Apply. 1.3 Sample Feature Applications This section describes some possible scenarios and topologies that you can set up using your Zyxel Device.
Page 18: Dual-Radio
Chapter 1 Introduction Figure 3 Multiple BSSs 1.3.2 Dual-Radio Some of the Zyxel Device models are equipped with dual wireless radios. This means you can configure two different wireless networks to operate simultaneously. Note: A different channel should be configured for each WLAN interface to reduce the effects of radio interference.
Page 19: Zyxel Device Product Feature Comparison
Chapter 1 Introduction Figure 4 Dual-Radio Application 1.4 Zyxel Device Product Feature Comparison The following tables show the differences between each Zyxel Device model. Table 1 Zyxel Device 1000/5000 Series Comparison Table NWA1123- NWA1123- NWA1123- NWA110A NWA1302- NWA5123- NWA5123- WAC5302 FEATURES AC PRO AC HD...
Page 20 Chapter 1 Introduction Table 1 Zyxel Device 1000/5000 Series Comparison Table (continued) NWA1123- NWA1123- NWA1123- NWA110A NWA1302- NWA5123- NWA5123- WAC5302 FEATURES AC PRO AC HD AC HD Monitor Mode & Rogue APs Containment Rogue AP Detection WDS (Wireless Distribution System) - Root AP &...
Page 21 Chapter 1 Introduction Table 1 Zyxel Device 1000/5000 Series Comparison Table (continued) NWA1123- NWA1123- NWA1123- NWA110A NWA1302- NWA5123- NWA5123- WAC5302 FEATURES AC PRO AC HD AC HD Grounding Maximum 256 event number of log 512 event logs and 1024 debug logs logs and 1 debug logs messages...
Page 22 Chapter 1 Introduction Table 2 WAC 6000 Series Comparison Table (continued) WAC6103D WAC6303D WAC6502D WAC6502D WAC6503D WAC6552D WAC6553D FEATURES NebulaFlex PRO NCC Discovery 802.11r Fast Roaming Support 802.11k/v Assisted Roaming Bluetooth Low Energy (BLE) USB Port for BLE Ethernet Storm Control Grounding Maximum number of log 512 event logs and 1024 debug logs...
Page 23 Chapter 1 Introduction Table 3 WAX 500/600 Series Comparison Table (continued) FEATURES WAX510D WAX650S Antenna Switch (per AP) Console Port 4-Pin Serial 4-Pin Serial LED Locator LED Suppression AC (AP Controller) Discovery NebulaFlex PRO NCC Discovery 802.11r Fast Roaming Support 802.11k/v Assisted Roaming Bluetooth Low Energy (BLE) USB Port for BLE...
Page 24: Ap Management
H A P T E R AP Management 2.1 Management Mode The Zyxel Device is a unified AP and can be managed by the NCC or an AP controller (AC), or work as a standalone device. We recommend you use NCC to manage multiple APs (see the NCC User’s Guide). An AP Controller such as the NXC can only manage multiple APs in the same location.
Page 25 Chapter 2 AP Management switches and gateways. Your network can also be managed through your smartphone using the Nebula Mobile app. See Section 25.1 on page 226 for an example NCC managed network topology. NCC allows different levels of management. You can configure each device on its own or configure a set of devices together as a site.
Page 26: Ap Controller (Ac)
Chapter 2 AP Management See the NCC (Nebula Control Center) User’s Guide for how to configure Nebula managed devices. See Chapter 27 on page 230 if you want to change the Zyxel Device’s VLAN setting or manually set its IP address.
Page 27: Zyxel One Network (Zon) Utility
Chapter 2 AP Management discovered. NCC-to-Standalone Unregister the Zyxel Device from the NCC organization/site. Reset the Zyxel Device to factory defaults (see Section 29.6 on page 246). AC-to-Standalone Use the Reset button to return the Zyxel Device to its factory default settings (see Section 29.6 on page 246).
Page 28: Run The Zon Utility
Chapter 2 AP Management • 2 GB RAM • 100 MB free hard disk • WXGA (Wide XGA 1280x800) 2.3.2 Run the ZON Utility Double-click the ZON Utility to run it. The first time you run the ZON Utility, you will see if your device and firmware version support the ZON Utility.
Page 29 Chapter 2 AP Management Figure 7 ZON Utility Screen Select a network adapter to which your supported devices are connected. Figure 8 Network Adapter Click the Go button for the ZON Utility to discover all supported devices in your network. Figure 9 Discovery The ZON Utility screen shows the devices discovered.
Page 30 Chapter 2 AP Management Figure 10 ZON Utility Screen Select a device and then use the icons to perform actions. Some functions may not be available for your devices. Note: You must know the selected device admin password before taking actions on the device using the ZON utility icons.
Page 31: Ways To Access The Zyxel Device
Chapter 2 AP Management Table 6 ZON Utility Icons (continued) ICON DESCRIPTION 9 Configure NCC You must have Internet access to use this feature. Use this icon to enable or disable the Discovery Nebula Control Center (NCC) discovery feature on the selected device. If it is enabled, the selected device will try to connect to the NCC.
Page 32: Good Habits For Managing The Zyxel Device
Chapter 2 AP Management This is the primary means by which you manage the Zyxel Device in cloud (NCC) mode. With the NCC, you can remotely manage and monitor the Zyxel Device through a cloud-based network management system. See the NCC User’s Guide for more information. ZON Utility Zyxel One Network (ZON) Utility is a utility tool that assists you to set up and maintain network devices in a simple and efficient way.
Page 33: Hardware
H A P T E R Hardware See the Quick Start Guide for hardware installation and connections. 3.1 Grounding (WAC6552D-S and WAC6553D-E) Earth grounding helps protect against lightning and interference. Note: The power installation must be performed by qualified service personnel and should conform to the National Electrical Code.
Page 34: Zyxel Device Models With Single Leds
Chapter 3 Hardware Figure 12 Grounding Example 3.2 Zyxel Device Models With Single LEDs The LEDs of some Zyxel Device models can be controlled by using the suppression feature such that the LEDs stay lit (ON) or OFF after the Zyxel Device is ready. Some Zyxel Device models also has Locator LED which allows you to see the actual location of the Zyxel Device among several devices in the network.
Page 35 Chapter 3 Hardware Figure 13 NWA1123-ACv2 LED The following are the LED descriptions for your NWA1123-ACv2. Table 8 NWA1123-ACv2 LED COLOR STATUS DESCRIPTION Amber Blinks amber for 1 second The LED blinks amber and green alternatively when the Zyxel and green for 1 second Device is booting up or is connecting to the NCC.
Page 36: Wac6303D-S And Nwa5123-Ac Hd
Chapter 3 Hardware Table 8 NWA1123-ACv2 LED (continued) COLOR STATUS DESCRIPTION Steady On The Zyxel Device failed to boot up or is experiencing system failure. Slow Blinking (Blink for 3 The Uplink interface is down. times, Off for 3s) Fast Blinking (On for 50 ms, The Zyxel Device is undergoing firmware upgrade.
Page 37: Nwa1123-Ac Hd
Chapter 3 Hardware Table 9 WAC6303D-S and NWA5123-AC HD LED (continued) COLOR STATUS DESCRIPTION Amber Blinks amber and green The Zyxel Device is managed by an AC but the uplink is alternatively 2 times and disconnected. Green then turns solid green for 3 seconds.
Page 38 Chapter 3 Hardware Figure 15 NWA1123-AC HD LED The following are the LED descriptions for your NWA1123-AC HD. Table 10 NWA1123-AC HD LED COLOR STATUS DESCRIPTION Amber Blinks amber for 1 second The Zyxel Device is booting up or connecting with NCC. and green for 1 second alternatively.
Page 39: Nwa5123-Ac
Chapter 3 Hardware Table 10 NWA1123-AC HD LED (continued) COLOR STATUS DESCRIPTION White Steady On The Zyxel Device’s wireless interface is activated, but there are no wireless clients connected when it is in limited power mode (see Table 26 on page 67).
Page 40: Nwa110Ax, Wax510D And Wax650S
Chapter 3 Hardware The following are the LED descriptions for your NWA5123-AC. Table 11 NWA5123-AC LED COLOR STATUS DESCRIPTION Amber Blinks amber for 1 second The Zyxel Device is booting up. and green for 1 second Green alternatively. Amber Blinks amber and green The Zyxel Device is discovering an AC.
Page 41 Chapter 3 Hardware Figure 17 NWA110AX, WAX510D and WAX650S LED The following are the LED descriptions for your NWA110AX, WAX510D and WAX650S. Table 12 NWA110AX, WAX510D and WAX650S LED COLOR STATUS DESCRIPTION Amber Blinks amber for 1 second The Zyxel Device is booting up or is connecting with NCC. and green for 1 second alternatively.
Page 42: Zyxel Device Models With Multiple Leds
Chapter 3 Hardware Table 12 NWA110AX, WAX510D and WAX650S LED (continued) COLOR STATUS DESCRIPTION Amber Steady On The Zyxel Device is ready for use, the Zyxel Device’s wireless interface is activated, and/or wireless clients are connected to the Zyxel Device in limited power mode (see Table 26 on page 67).
Page 43 Chapter 3 Hardware Figure 18 NWA1123-AC PRO LEDs The following table describes the LEDs. Table 13 NWA1123-AC PRO LEDs COLOR STATUS DESCRIPTION PWR/SYS Amber Blinks amber for 1 The LED blinks amber and green alternatively when the second and green for Zyxel Device is booting up.
Page 44: Nwa1302-Ac
Chapter 3 Hardware Table 13 NWA1123-AC PRO LEDs (continued) COLOR STATUS DESCRIPTION Management Green The Zyxel Device is managed by the NCC. Slow Blinking (On for 1 The Zyxel Device is using default wireless settings, or the sec, Off for 1 sec) Zyxel Device is connected to the NCC but is unregistered with the NCC.
Page 45 Chapter 3 Hardware Figure 19 NWA1302-AC LEDs The following table describes the LEDs. Table 14 NWA1302-AC LEDs COLOR STATUS DESCRIPTION PWR/SYS Amber Blinks amber for 1 The LED blinks amber and green alternatively when the second and green for 1 Zyxel Device is booting up.
Page 46: Wac6502D-E, Wac6502D-S, And Wac6503D-S
Chapter 3 Hardware Table 14 NWA1302-AC LEDs (continued) COLOR STATUS DESCRIPTION UPLINK Amber The port is operating as a 10/100 Mbps connection. Blinking The Zyxel Device is sending/receiving data through the port at 10/100 Mbps. Green The port is operating as a Gigabit connection (1000 Mbps).
Page 47 Chapter 3 Hardware Figure 20 WAC6502D-E, WAC6502D-S, or WAC6503D-S LEDs The following table describes the LEDs. Table 15 WAC6502D-E, WAC6502D-S, or WAC6503D-S LEDs COLOR STATUS DESCRIPTION PWR/SYS Amber Blinks amber for 1 The Zyxel Device is booting up or is connecting to the second and green for 1 NCC or to an AC.
Page 48: Wac6103D-I
Chapter 3 Hardware Table 15 WAC6502D-E, WAC6502D-S, or WAC6503D-S LEDs (continued) COLOR STATUS DESCRIPTION Management Green The Zyxel Device is managed by a the NCC or an AC. Slow Blinking (Blink for 3 The Zyxel Device is searching (discovery) for an AC. times, Off for 3s) Slow Blinking (On for 1s, The Zyxel Device is using default wireless settings, or the...
Page 49 Chapter 3 Hardware Figure 21 WAC6103D-I LEDs The following table describes the LEDs. Table 16 WAC6103D-I LEDs COLOR STATUS DESCRIPTION PWR/SYS Amber Blinks amber for 1 The Zyxel Device is booting up. second and green for 1 Green second alternatively. Green The Zyxel Device is ready for use.
Page 50: Wac5302D-S
Chapter 3 Hardware Table 16 WAC6103D-I LEDs (continued) COLOR STATUS DESCRIPTION Management Green The Zyxel Device is managed by an AC or the NCC. Slow Blinking (Blink for 3 The Zyxel Device is searching (discovery) for an AC. times, Off for 3s) Slow Blinking (On for 1s, The Zyxel Device is using default wireless settings, or the Off for 1s)
Page 51 Chapter 3 Hardware Figure 22 WAC5302D-S LEDs The following table describes the LEDs. Table 17 WAC5302D-S LEDs COLOR STATUS DESCRIPTION PWR/SYS Amber Blinks amber for 1 The LED blinks amber and green alternatively when the second and green for 1 WAC is booting up.
Page 52 Chapter 3 Hardware Table 17 WAC5302D-S LEDs (continued) COLOR STATUS DESCRIPTION UPLINK Amber The port is operating as a 10/100 Mbps connection. Blinking The Zyxel Device is sending/receiving data through the port at 10/100 Mbps. Green The port is operating as a Gigabit connection (1000 Mbps).
Page 53: Web Configurator
H A P T E R Web Configurator 4.1 Overview The Web Configurator is an HTML-based management interface that allows easy system setup and management via internet browser. Use a browser that supports HTML5, such Internet Explorer 11, Mozilla Firefox, or Google Chrome. The recommended screen resolution is 1024 by 768 pixels. In order to use the Web Configurator you need to allow: •...
Page 54 Chapter 4 Web Configurator If a Zyxel Device is in standalone mode and supports NCC, the login page displays as shown in the following figure. Click Nebula Mode to show the following screen. Here, you can watch a tutorial for using the Zyxel Nebula Control Center (NCC) or access the link to the NCC, as shown in the following figure.
Page 55: Navigating The Web Configurator
Chapter 4 Web Configurator If you want to return to the login page, click Standalone Mode and follow the next steps. Enter the user name (default: “admin”) and password (default: “1234”). If the Zyxel Device is being managed or has been managed by the NCC, check the NCC's Site-Wide > Configure > General setting screen for the Zyxel Device's current password.
Page 56: Title Bar
Chapter 4 Web Configurator Figure 23 The Web Configurator’s Main Screen for Standalone Mode Figure 24 The Web Configurator’s Main Screen for Cloud Mode The Web Configurator’s main screen is divided into these parts: • A - Title Bar • B - Navigation Panel •...
Page 57 Chapter 4 Web Configurator Figure 25 Title Bar The icons provide the following functions. Table 18 Title Bar: Web Configurator Icons LABEL DESCRIPTION Wizard Click this to open the wizard. See Chapter 7 on page 73 for more information. Help Click this to open the help page for the current screen.
Page 58: Navigation Panel
Chapter 4 Web Configurator Figure 27 CLI Messages Click Clear to remove the currently displayed information. Note: See the Command Reference Guide for information about the commands. 4.3.2 Navigation Panel Use the menu items on the navigation panel to open screens to configure Zyxel Device features. Click the arrow in the middle of the right edge of the navigation panel to hide the navigation panel menus or drag it to resize them.
Page 59 Chapter 4 Web Configurator Monitor Menu The monitor menu screens display status and statistics information. Table 19 Monitor Menu Screens Summary FOLDER OR LINK FUNCTION Network Status Network Display general LAN interface information and packet statistics. Status Wireless AP Information Radio List Display information about the radios of the connected APs.
Page 60: Cloud Mode Navigation Panel Menus
Chapter 4 Web Configurator Table 20 Configuration Menu Screens Summary (continued) FOLDER OR LINK FUNCTION WDS Profile Create and manage WDS profiles that can be used to connect to different APs in WDS. Certificate My Certificates Create and manage th e Zyxel Device’s certificates. Trusted Certificates Import and manage certificates from trusted sources.
Page 61: Tables And Lists
Chapter 4 Web Configurator Dashboard The dashboard displays general Zyxel Device information, and AP information in widgets that you can re-arrange to suit your needs. For details on the Dashboard’s features, see Chapter 26 on page 228. Configuration Menu Use the configuration menu screens to configure the Zyxel Device’s features. Table 22 Configuration Menu Screens Summary FOLDER OR LINK FUNCTION...
Page 62 Chapter 4 Web Configurator Select a column heading cell’s right border and drag to re-size the column. Select a column heading and drag and drop it to change the column order. A green check mark displays next to the column’s title when you drag the column to a valid new location. Use the icons and fields at the bottom of the table to navigate to different pages of entries and control how many entries display at a time.
Page 63 Chapter 4 Web Configurator 4.3.5.2 Working with Table Entries The tables have icons for working with table entries. A sample is shown next. You can often use the [Shift] or [Ctrl] key to select multiple entries to remove, activate, or deactivate. Table 23 Common Table Icons Here are descriptions for the most common table icons.
Page 64: Standalone Configuration
Standalone Configuration...
Page 65: Standalone Configuration
H A P T E R Standalone Configuration 5.1 Overview The Zyxel Device is in standalone mode by default. Use the web configurator to manage and configure the Zyxel Device directly. As shown in the following figure, wireless clients can connect to the Zyxel Device (A) to access network resources.
Page 66 Chapter 5 Standalone Configuration Table 25 Starting and Stopping the Zyxel Device METHOD DESCRIPTION Using the RESET button If you press the RESET button on the back of the Zyxel Device, the Zyxel Device sets the configuration to its default values and then reboots. See Section 29.6 on page 246 more information.
Page 67: Dashboard
H A P T E R Dashboard 6.1 Overview This screen displays general device information, system status, system resource usage, and interface status in widgets that you can re-arrange to suit your needs. You can also collapse, refresh, and close individual widgets.
Page 68 Chapter 6 Dashboard Table 26 Dashboard (continued) LABEL DESCRIPTION Serial Number This field displays the serial number of this Zyxel Device. MAC Address This field displays the MAC addresses used by the Zyxel Device. Each physical port or Range wireless radio has one MAC address. The first MAC address is assigned to the Ethernet LAN port, the second MAC address is assigned to the first radio, and so on.
Page 69 Chapter 6 Dashboard Table 26 Dashboard (continued) LABEL DESCRIPTION Current Login This field displays the user name used to log in to the current session, the amount of User reauthentication time remaining, and the amount of lease time remaining. Boot Status This field displays details about the Zyxel Device’s startup state.
Page 70: Cpu Usage
Chapter 6 Dashboard Table 26 Dashboard (continued) LABEL DESCRIPTION Status This field displays the current status of each interface. The possible values depend on what type of interface it is. Inactive - The Ethernet interface is disabled. Down - The Ethernet interface is enabled but not connected. Speed / Duplex - The Ethernet interface is enabled and connected.
Page 71: Memory Usage
Chapter 6 Dashboard Figure 30 Dashboard > CPU Usage The following table describes the labels in this screen. Table 27 Dashboard > CPU Usage LABEL DESCRIPTION The y-axis represents the percentage of CPU usage. time The x-axis shows the time period over which the CPU usage occurred. Refresh Interval Enter how often you want this window to be automatically updated.
Page 72 Chapter 6 Dashboard The following table describes the labels in this screen. Table 28 Dashboard > Memory Usage LABEL DESCRIPTION The y-axis represents the percentage of RAM usage. time The x-axis shows the time period over which the RAM usage occurred Refresh Interval Enter how often you want this window to be automatically updated.
Page 73: Setup Wizard
H A P T E R Setup Wizard 7.1 Accessing the Wizard When you log into the Web Configurator for the first time or when you reset the Zyxel Device to its default configuration, the wizard screen displays. Note: If you have already configured the wizard screens and want to open it again, click the Wizard icon on the upper right corner of any Web Configurator screen.
Page 74: Step 2 Password And Uplink Connection
Chapter 7 Setup Wizard Figure 32 Wizard: Time Settings 7.2.2 Step 2 Password and Uplink Connection Use this screen to configure the Zyxel Device’s system password and IP address. Change Password: Enter a new password and retype it to confirm. Uplink Connection: Select Auto (DHCP) if the Zyxel Device is connected to a router with the DHCP server enabled.
Page 75: Step 3 Radio
Chapter 7 Setup Wizard Figure 33 Wizard: Change Password and Uplink Connection 7.2.3 Step 3 Radio Use this screen to configure the Zyxel Device’s radio transmitter(s). • Channel Selection: Select Auto to have the Zyxel Device automatically choose a radio channel that has least interference.
Page 76: Step 4 Ssid
Chapter 7 Setup Wizard Figure 34 Wizard: Radio 7.2.4 Step 4 SSID Use this screen to enable, disable or edit an SSID profile. Select an SSID profile and click the Status switch to turn it on or off. To change an SSID profile’s settings, such as the SSID (WiFi network name) and WiFi password, double-click the SSID profile entry from the list.
Page 77 Chapter 7 Setup Wizard The screen varies depending on the security type you selected. • SSID: Enter a descriptive name of up to 32 printable characters for the wireless LAN. • VLAN ID: Enter a VLAN ID for the Zyxel Device to use to tag traffic originating from this SSID. Band Mode: Select the wireless band which this profile should use.
Page 78: Summary
Chapter 7 Setup Wizard Figure 37 Wizard: SSID: Edit (WPA2-Enterprise) 7.2.5 Summary Use this screen to check whether what you have configured is correct. Click Save to apply your settings and complete the wizard setup. Otherwise, click Prev to return to the previous screen or click Cancel to close the wizard without saving.
Page 79: Monitor
H A P T E R Monitor 8.1 Overview Use the Monitor screens to check status and statistics information. 8.1.1 What You Can Do in this Chapter • The Network Status screen (Section 8.3 on page 80) displays general LAN interface information and packet statistics.
Page 80: Network Status
Chapter 8 Monitor 8.3 Network Status Use this screen to look at general Ethernet interface information and packet statistics. To access this screen, click Monitor > Network Status. Figure 39 Monitor > Network Status The following table describes the labels in this screen. Table 29 Monitor >...
Page 81: Port Statistics Graph
Chapter 8 Monitor Table 29 Monitor > Network Status (continued) LABEL DESCRIPTION Set Interval Click this to set the Poll Interval the screen uses. Stop Click this to stop the window from updating automatically. You can start it again by setting the Poll Interval and clicking Set Interval.
Page 82: Radio List
Chapter 8 Monitor Figure 40 Monitor > Network Status > Switch to Graphic View The following table describes the labels in this screen. Table 30 Monitor > Network Status > Switch to Graphic View LABEL DESCRIPTION Refresh Interval Enter how often you want this window to be automatically updated. Refresh Now Click this to update the information in the window right away.
Page 83 Chapter 8 Monitor Figure 41 Monitor > Wireless > AP Information > Radio List (for Zyxel Device that supports WDS) Figure 42 Monitor > Wireless > AP Information > Radio List (for Zyxel Device that does not support WDS) The following table describes the labels in this screen. Table 31 Monitor >...
Page 84: Ap Mode Radio Information
Chapter 8 Monitor Table 31 Monitor > Wireless > AP Information > Radio List (continued) LABEL DESCRIPTION Upload This displays the total number of packets received by the radio. Download This displays the total number of packets transmitted by the radio. Channel This indicates how much IEEE 802.11 traffic the radio can receive on the channel.
Page 85 Chapter 8 Monitor Figure 43 Monitor > Wireless > AP Information > Radio List > More Information The following table describes the labels in this screen. Table 32 Monitor > Wireless > AP Information > Radio List > More Information LABEL DESCRIPTION SSID Detail...
Page 86: Station List
Chapter 8 Monitor Table 32 Monitor > Wireless > AP Information > Radio List > More Information (continued) LABEL DESCRIPTION SSID Name This displays an SSID associated with this radio. There can be up to eight maximum. BSSID This displays a BSSID associated with this radio. The BSSID is tied to the SSID. Security This displays the security mode in which the SSID is operating.
Page 87: Wds Link Info
Chapter 8 Monitor Table 33 Monitor > Wireless > Station Info (continued) LABEL DESCRIPTION SSID Name This indicates the name of the wireless network to which the station is connected. A single AP can have multiple SSIDs or networks. Security Mode This indicates which secure encryption methods is being used by the station to connect to the network.
Page 88: Detected Device
Chapter 8 Monitor Table 34 Monitor > Wireless > WDS Link Info (continued) LABEL DESCRIPTION MAC Address This is the MAC address of the root AP or repeater to which the Zyxel Device is connected using WDS. Radio This is the radio number on the root AP or repeater to which the Zyxel Device is connected using WDS.
Page 89 Chapter 8 Monitor Figure 46 Monitor > Wireless > Detected Device (for Zyxel Device that supports Monitor mode) NWA/WAC/WAX Series User’s Guide...
Page 90 Chapter 8 Monitor Figure 47 Monitor > Wireless > Detected Device (for Zyxel Device that does not support Monitor mode) The following table describes the labels in this screen. Table 35 Monitor > Wireless > Detected Device LABEL DESCRIPTION Discovered APs Rogue AP This shows how many devices are detected as rogue APs.
Page 91: View Log
Chapter 8 Monitor Table 35 Monitor > Wireless > Detected Device (continued) LABEL DESCRIPTION Mark as Rogue Click this button to mark the selected AP as a rogue AP. For more on managing rogue APs, see the Configuration > Wireless > Rogue AP screen (Section 10.3 on page 109).
Page 92 Chapter 8 Monitor Figure 48 Monitor > Log > View Log The following table describes the labels in this screen. Table 36 Monitor > Log > View Log LABEL DESCRIPTION Show Filter / Hide Click this button to show or hide the filter settings. Filter If the filter settings are hidden, the Display, Email Log Now, Refresh, and Clear Log fields are available.
Page 93 Chapter 8 Monitor Table 36 Monitor > Log > View Log (continued) LABEL DESCRIPTION Destination This displays when you show the filter. Type the IP address of the destination of the incoming Address packet when the log message was generated. Do not include the port in this filter. Source Interface This displays when you show the filter.
Page 94: Network
H A P T E R Network 9.1 Overview This chapter describes how you can configure the management IP address and VLAN settings of your Zyxel Device. The Internet Protocol (IP) address identifies a device on a network. Every networking device (including computers, servers, routers, printers, etc.) needs an IP address to communicate across the network.
Page 95 Chapter 9 Network Figure 50 AC managed Network Example Note: The Zyxel Device can be a standalone device or be managed by an AC. AC Discovery and Management The link between AC Discovery-enabled access points proceeds as follows: An Zyxel Device with AC Discovery enabled joins a wired network (receives a dynamic IP address). The Zyxel Device sends out a discovery request, looking for an AC.
Page 96: What You Can Do In This Chapter
Chapter 9 Network Note: The AC needs to have a static IP address. If it is a DHCP client, set the DHCP server to reserve an IP address for the AC. AC management and IP Subnets By default, CAPWAP works only between Zyxel Devices with IP addresses in the same subnet. However, you can configure the Zyxel Device and the AC to use CAPWAP with IP addresses in different subnets by doing the following.
Page 97: Ip Setting
Chapter 9 Network • The NCC Discovery screen (Section 9.6 on page 103) configures the Zyxel Device’s Nebula Control Center (NCC) discovery settings. 9.2 IP Setting Use this screen to configure the IP address for your Zyxel Device. To access this screen, click Configuration >...
Page 98: Vlan
Chapter 9 Network Table 37 Configuration > Network > IP Setting (continued) LABEL DESCRIPTION DNS Server IP Enter the IP address of the DNS server. Address IPv6 Address Assignment Enable Stateless Select this to enable IPv6 stateless auto-configuration on the Zyxel Device. The Zyxel Device Address Auto- will generate an IPv6 address itself from a prefix obtained from an IPv6 router in the network.
Page 99 Chapter 9 Network Figure 53 Management VLAN Setup In the figure above, to access and manage the Zyxel Device from computer A, the Zyxel Device and switch B’s ports to which computer A and the Zyxel Device are connected should be in the same VLAN. A Virtual Local Area Network (VLAN) allows a physical network to be partitioned into multiple logical networks.
Page 100 Chapter 9 Network Figure 54 Configuration > Network > VLAN (for Zyxel Device with multiple Ethernet ports) Figure 55 Configuration > Network > VLAN (for Zyxel Device with one Ethernet port) Each field is described in the following table. Table 38 Configuration > Network > VLAN LABEL DESCRIPTION VLAN Settings...
Page 101: Storm Control
Chapter 9 Network Table 38 Configuration > Network > VLAN (continued) LABEL DESCRIPTION PVID This field displays the port number of the VLAN ID. VLAN Configuration Click this to create a new entry. For features where the entry’s position in the numbered list is important (features where the Zyxel Device applies the table’s entries in order like the SSID for example), you can select an entry and click Add to create a new entry after the selected entry.
Page 102: Ac (Ap Controller) Discovery
Chapter 9 Network Each field is described in the following table. Table 39 Configuration > Network > Storm Control LABEL DESCRIPTION Broadcast Storm Select the check box to enable broadcast storm control on the Zyxel Device. Enabling this Control will drop ingress broadcast traffic in the physical Ethernet port if it exceeds the maximum traffic rate.
Page 103: Ncc Discovery
Chapter 9 Network Each field is described in the following table. Table 40 Configuration > Network > AC Discovery LABEL DESCRIPTION Discovery Setting Auto Select this option to use DHCP option 138/DNS SRV record/Broadcast to get the AC’s IP address. If the Zyxel Device and a Zyxel AC, such as the NXC2500 or NXC5500, are in the same subnet, it will be managed by the controller automatically.
Page 104 Chapter 9 Network Each field is described in the following table. Table 41 Configuration > Network > NCC Discovery LABEL DESCRIPTION Nebula Control Center Status Internet This field displays whether the Zyxel Device can connect to the Internet. Nebula Connectivity This field displays whether the Zyxel Device can connect to the Zyxel Nebula Control Center (NCC).
Page 105: Wireless
H A P T E R Wireless 10.1 Overview This chapter discusses how to configure the wireless network settings in your Zyxel Device. The following figure provides an example of a wireless network. Figure 59 Example of a Wireless Network The wireless network is the part in the blue circle.
Page 106: What You Need To Know
Chapter 10 Wireless 10.1.2 What You Need to Know The following terms and concepts may help as you read this chapter. Station / Wireless Client A station or wireless client is any wireless-capable device that can connect to an AP using a wireless signal.
Page 107 Chapter 10 Wireless Figure 60 Configuration > Wireless > AP Management Each field is described in the following table. Table 42 Configuration > Wireless > AP Management LABEL DESCRIPTION Radio 1 Setting Radio 1 Activate Select the check box to enable the Zyxel Device’s first (default) radio. NWA/WAC/WAX Series User’s Guide...
Page 108 Chapter 10 Wireless Table 42 Configuration > Wireless > AP Management (continued) LABEL DESCRIPTION Radio 1 OP Mode Select the operating mode for radio 1. AP Mode means the radio can receive connections from wireless clients and pass their data traffic through to the Zyxel Device to be managed (or subsequently passed on to an upstream gateway for managing).
Page 109: Rogue Ap
Chapter 10 Wireless Table 42 Configuration > Wireless > AP Management (continued) LABEL DESCRIPTION Radio 2 OP Mode This displays if the Zyxel Device has a second radio. Select the operating mode for radio 2. AP Mode means the radio can receive connections from wireless clients and pass their data traffic through to the Zyxel Device to be managed (or subsequently passed on to an upstream gateway for managing).
Page 110 Chapter 10 Wireless Rogue APs A rogue AP is a wireless access point operating in a network’s coverage area that is not under the control of the network administrator, and which can potentially open up holes in a network’s security. In the following example, a corporate network’s security is compromised by a rogue AP (RG) set up by an employee at his workstation in order to allow him to connect his notebook computer wirelessly (A).
Page 111 Chapter 10 Wireless know which models support Rogue AP Detection. Note: Enabling Rogue AP Detection might affect the performance of wireless clients associated with the Zyxel Device. Figure 62 Configuration > Wireless > Rogue AP (for Zyxel Devices that support Monitor mode) NWA/WAC/WAX Series User’s Guide...
Page 112 Chapter 10 Wireless Figure 63 Configuration > Wireless > Rogue AP (for Zyxel Devices that support Rogue AP Detection) Each field is described in the following table. Table 43 Configuration > Wireless > Rogue AP LABEL DESCRIPTION Rogue AP Detection Setting Enable Rogue AP Select this check box to detect Rogue APs in the network.
Page 113: Add/Edit Rogue/Friendly List
Chapter 10 Wireless Table 43 Configuration > Wireless > Rogue AP (continued) LABEL DESCRIPTION Role This field indicates whether the selected AP is a rogue-ap or a friendly-ap. To change the AP’s role, click the Edit button. MAC Address This field indicates the AP’s radio MAC address. Description This field displays the AP’s description.
Page 114: Load Balancing
Chapter 10 Wireless 10.4 Load Balancing Use this screen to configure wireless network traffic load balancing between the APs on your network (see Load Balancing on page 118). Click Configuration > Wireless > Load Balancing to access this screen. Figure 65 Configuration > Wireless > Load Balancing Each field is described in the following table.
Page 115: Disassociating And Delaying Connections
Chapter 10 Wireless Table 45 Configuration > Wireless > Load Balancing (continued) LABEL DESCRIPTION Disassociate This function is enabled by default and the disassociation priority is always Signal Strength station when when you set Mode to By Smart Classroom. overloaded Select this option to disassociate wireless clients connected to the AP when it becomes overloaded.
Page 116: Dcs
Chapter 10 Wireless bandwidth allotment. Figure 67 Disassociating with a Client Connections are cut based on either idle timeout or signal strength. The Zyxel Device first looks to see which devices have been idle the longest, then starts kicking them in order of highest idle time. If no connections are idle, the next criteria the Zyxel Device analyzes is signal strength.
Page 117: Technical Reference
Chapter 10 Wireless 10.6 Technical Reference The following section contains additional technical information about the features described in this chapter. Dynamic Channel Selection When numerous APs broadcast within a given area, they introduce the possibility of heightened radio interference, especially if some or all of them are broadcasting on the same radio channel. If the interference becomes too great, then the network administrator must open his AP configuration options and manually change the channel to one that no other AP is using (or at least a channel that has a lower level of interference) in order to give the connected stations a minimum degree of interference.
Page 118 Chapter 10 Wireless Finally, there is an alternative four channel scheme for ETSI, consisting of channels 1, 5, 9, 13. This offers significantly less overlap that the other one. Figure 71 An Alternative Four-Channel Deployment Load Balancing Because there is a hard upper limit on an AP’s wireless bandwidth, load balancing can be crucial in areas crowded with wireless users.
Page 119: Bluetooth
H A P T E R Bluetooth 11.1 Overview Use this screen to configure the iBeacon advertising settings for the Zyxel Device that supports Bluetooth Low Energy (BLE). Bluetooth Low Energy, which is also known as Bluetooth Smart, transmits less data over a shorter distance but consumes less power than classic Bluetooth.
Page 120: Bluetooth Advertising Settings
Chapter 11 Bluetooth 11.2 Bluetooth Advertising Settings The Zyxel Device communicates with another BLE enabled device for advertisements. Use this screen to configure up to five beacon IDs to be included in the advertising packet. To access this screen, click Configuration > Bluetooth > Advertising Settings. Figure 72 Configuration >...
Page 121 Chapter 11 Bluetooth Figure 73 Configuration > Bluetooth > Advertising Settings > Edit The following table describes the labels in this screen. Table 48 Configuration > Bluetooth > Advertising Settings > Edit LABEL DESCRIPTION Activate Select this option to enable the advertising settings. UUID To specify a UUID for the Zyxel Device’s beacon ID, enter 32 hexadecimal digits in the range of “A-F”, “a-f”...
Page 122: User
H A P T E R User 12.1 Overview This chapter describes how to set up user accounts and user settings for the Zyxel Device. 12.1.1 What You Can Do in this Chapter • The User screen (see Section 12.2 on page 123) provides a summary of all user accounts.
Page 123: User Summary
Chapter 12 User 12.2 User Summary The User screen provides a summary of all user accounts. To access this screen click Configuration > Object > User. Figure 74 Configuration > Object > User The following table describes the labels in this screen. Table 50 Configuration >...
Page 124 Chapter 12 User • - [dashes] The first character must be alphabetical (A-Z a-z), an underscore (_), or a dash (-). Other limitations on user names are: • User names are case-sensitive. If you enter a user 'bob' but use 'BOB' when connecting via CIFS or FTP, it will use the account settings used for 'BOB' not ‘bob’.
Page 125: Setting
Chapter 12 User Table 51 Configuration > User > User > Add/Edit A User (continued) LABEL DESCRIPTION Authentication This field is not available if the user type is user. Timeout Settings If you want to set authentication timeout to a value other than the default settings, select Use Manual Settings then fill your preferred values in the fields that follow.
Page 126 Chapter 12 User Figure 76 Configuration > Object > User > Setting The following table describes the labels in this screen. Table 52 Configuration > Object > User > Setting LABEL DESCRIPTION User Default Setting Default Authentication These authentication timeout settings are used by default when you create a new Timeout Settings user account.
Page 127: Edit User Authentication Timeout Settings
Chapter 12 User Table 52 Configuration > Object > User > Setting (continued) LABEL DESCRIPTION Limit the number of Select this check box if you want to set a limit on the number of simultaneous logins simultaneous logons for by admin users. If you do not select this, admin users can login as many times as they administration account want at the same time using the same or different IP addresses.
Page 128 Chapter 12 User The following table describes the labels in this screen. Table 53 User > Setting > Edit User Authentication Timeout Settings LABEL DESCRIPTION User Type This read-only field identifies the type of user account for which you are configuring the default settings.
Page 129: Ap Profile
H A P T E R AP Profile 13.1 Overview This chapter shows you how to configure preset profiles for the Zyxel Device. 13.1.1 What You Can Do in this Chapter • The Radio screen (Section 13.2 on page 130) creates radio configurations that can be used by the APs.
Page 130: Radio
Chapter 13 AP Profile WEP (Wired Equivalent Privacy) encryption scrambles all data packets transmitted between the AP and the wireless stations associated with it in order to keep network communications private. Both the wireless stations and the access points must use the same WEP key for data encryption and decryption. WPA2 WPA2 (IEEE 802.11i) is a wireless security standard that defines stronger encryption, authentication and key management than WPA.
Page 131: Add/Edit Radio Profile
Chapter 13 AP Profile Figure 78 Configuration > Object > AP Profile > Radio The following table describes the labels in this screen. Table 54 Configuration > Object > AP Profile > Radio LABEL DESCRIPTION Click this to add a new radio profile. Edit Click this to edit the selected radio profile.
Page 132 Chapter 13 AP Profile Figure 79 Configuration > Object > AP Profile > Radio > Add/Edit Profile The following table describes the labels in this screen. Table 55 Configuration > Object > AP Profile > Radio > Add/Edit Profile LABEL DESCRIPTION Hide / Show Click this to hide or show the Advanced Settings in this window.
Page 133 Chapter 13 AP Profile Table 55 Configuration > Object > AP Profile > Radio > Add/Edit Profile (continued) LABEL DESCRIPTION Profile Name Enter up to 31 alphanumeric characters to be used as this profile’s name. Spaces and underscores are allowed. 802.11 Band Select whether this radio would use the 2.4 GHz or 5 GHz band.
Page 134 Chapter 13 AP Profile Table 55 Configuration > Object > AP Profile > Radio > Add/Edit Profile (continued) LABEL DESCRIPTION Enable DCS This field is available when you set Channel Selection to DCS. Client Aware Select this to have the Zyxel Device switch channels only when there are no clients connected to it.
Page 135 Chapter 13 AP Profile Table 55 Configuration > Object > AP Profile > Radio > Add/Edit Profile (continued) LABEL DESCRIPTION Time Interval Select this option to have the Zyxel Device survey the other APs within its broadcast radius at the end of the specified time interval. DCS Time Interval This field is available when you set Channel Selection to DCS and select the Time Interval option.
Page 136: Ssid
Chapter 13 AP Profile Table 55 Configuration > Object > AP Profile > Radio > Add/Edit Profile (continued) LABEL DESCRIPTION Enable Signal Select the check box to use the signal threshold to ensure wireless clients receive good Threshold throughput. This allows only wireless clients with a strong signal to connect to the AP. Clear the check box to not require wireless clients to have a minimum signal strength to connect to the AP.
Page 137 Chapter 13 AP Profile makes a connection to it. To access this screen click Configuration > Object > AP Profile > SSID > SSID List. Note: You cannot add or remove an SSID profile after running the setup wizard. Figure 80 Configuration > Object > AP Profile > SSID > SSID List (Default) Figure 81 Configuration >...
Page 138: Add/Edit Ssid Profile
Chapter 13 AP Profile Table 56 Configuration > Object > AP Profile > SSID > SSID List (continued) LABEL DESCRIPTION This field indicates the QoS type associated with the SSID profile. MAC Filtering This field indicates which (if any) MAC filter Profile is associated with the SSID profile. Profile Layer-2 Isolation This field indicates which (if any) layer-2 isolation Profile is associated with the SSID profile.
Page 139 Chapter 13 AP Profile The following table describes the labels in this screen. Table 57 Configuration > Object > AP Profile > SSID > SSID List > Add/Edit SSID Profile LABEL DESCRIPTION Create new Select an object type from the list to create a new one associated with this SSID profile. Object Profile Name Enter up to 31 alphanumeric characters for the profile name.
Page 140: Security List
Chapter 13 AP Profile Table 57 Configuration > Object > AP Profile > SSID > SSID List > Add/Edit SSID Profile (continued) LABEL DESCRIPTION Uplink Define the maximum outgoing transmission data rate (either in mbps or kbps) on a per-station basis.
Page 141: Add/Edit Security Profile
Chapter 13 AP Profile Figure 83 Configuration > Object > AP Profile > SSID > Security List The following table describes the labels in this screen. Table 58 Configuration > Object > AP Profile > SSID > Security List LABEL DESCRIPTION Click this to add a new security profile.
Page 142 Chapter 13 AP Profile Figure 84 Configuration > Object > AP Profile > SSID > Security List > Add/Edit Security Profile NWA/WAC/WAX Series User’s Guide...
Page 143 Chapter 13 AP Profile The following table describes the labels in this screen. Table 59 Configuration > Object > AP Profile > SSID > Security List > Add/Edit Security Profile LABEL DESCRIPTION General Settings Profile Name Enter up to 31 alphanumeric characters for the profile name. This name is only visible in the Web Configurator and is only for management purposes.
Page 144 Chapter 13 AP Profile Table 59 Configuration > Object > AP Profile > SSID > Security List > Add/Edit Security Profile (continued) LABEL DESCRIPTION Key 1~4 Based on your Key Length selection, enter the appropriate length hexadecimal or ASCII key. Group Key Update Enter the interval (in seconds) at which the AP updates the group WPA2 encryption key.
Page 145: Mac Filter List
Chapter 13 AP Profile Table 59 Configuration > Object > AP Profile > SSID > Security List > Add/Edit Security Profile (continued) LABEL DESCRIPTION NAS Identifier If the RADIUS server requires the Zyxel Device to provide the NAS (Network Access Server) identifier attribute, enter it here.
Page 146: Layer-2 Isolation List
Chapter 13 AP Profile Figure 86 Configuration > Object > AP Profile > SSID > MAC Filter List > Add/Edit MAC Filter Profile The following table describes the labels in this screen. Table 61 Configuration > Object > AP Profile > SSID > MAC Filter List > Add/Edit MAC Filter Profile LABEL DESCRIPTION Profile Name...
Page 147 Chapter 13 AP Profile Note: Intra-BSS Traffic Blocking is activated when you enable layer-2 isolation. Figure 87 Layer-2 Isolation Application MAC addresses that are not listed in the layer-2 isolation table are blocked from communicating with the Zyxel Device’s wireless clients except for broadcast packets. Layer-2 isolation does not check the traffic between wireless clients that are associated with the same AP.
Page 148: Add/Edit Layer-2 Isolation Profile
Chapter 13 AP Profile 13.6.1 Add/Edit Layer-2 Isolation Profile This screen allows you to create a new layer-2 isolation profile or edit an existing one. To access this screen, click the Add button or select a layer-2 isolation profile from the list and click the Edit button. Note: You need to know the MAC address of each wireless client, AP, computer or router that you want to allow to communicate with the Zyxel Device's wireless clients.
Page 149: Mon Profile
H A P T E R MON Profile 14.1 Overview This screen allows you to set up monitor mode configurations that allow your Zyxel Device to scan for other wireless devices in the vicinity. Once detected, you can use the Wireless > MON Mode screen (Section 10.3 on page 109) to classify them as either rogue or friendly.
Page 150: Add/Edit Mon Profile
Chapter 14 MON Profile Table 64 Configuration > Object > MON Profile (continued) LABEL DESCRIPTION Object Click this to view which other objects are linked to the selected monitor mode profile (for Reference example, an AP management profile). This field is a sequential value, and it is not associated with a specific profile. Status This field shows whether or not the entry is activated.
Page 151 Chapter 14 MON Profile The following table describes the labels in this screen. Table 65 Configuration > Object > MON Profile > Add/Edit MON Profile LABEL DESCRIPTION Activate Select this to activate this monitor mode profile. Profile Name This field indicates the name assigned to the monitor mode profile. Channel dwell time Enter the interval (in milliseconds) before the Zyxel Device switches to another channel for monitoring.
Page 152: Wds Profile
H A P T E R WDS Profile 15.1 Overview This chapter shows you how to configure WDS (Wireless Distribution System) profiles for the Zyxel Device to form a WDS with other APs. 15.1.1 What You Can Do in this Chapter The WDS Profile screen (Section 15.2 on page 152) creates preset WDS configurations that can be used...
Page 153: Add/Edit Wds Profile
Chapter 15 WDS Profile 15.2.1 Add/Edit WDS Profile This screen allows you to create a new WDS profile or edit an existing one. To access this screen, click the Add button or select and existing profile and click the Edit button. Figure 93 Configuration >...
Page 154: Certificates
H A P T E R Certificates 16.1 Overview The Zyxel Device can use certificates (also called digital IDs) to authenticate users. Certificates are based on public-private key pairs. A certificate contains the certificate owner’s identity and public key. Certificates provide a way to exchange public keys for use in authentication. 16.1.1 What You Can Do in this Chapter •...
Page 155 Chapter 16 Certificates Additionally, Jenny uses her own private key to sign a message and Tim uses Jenny’s public key to verify the message. The Zyxel Device uses certificates based on public-key cryptology to authenticate users attempting to establish a connection, not to encrypt the data that you send after establishing a connection. The method used to secure the data that you send through an established connection depends on the type of connection.
Page 156: Verifying A Certificate
Chapter 16 Certificates • Binary PKCS#12: This is a format for transferring public key and private key certificates.The private key in a PKCS #12 file is within a password-encrypted envelope. The file’s password is not connected to your certificate’s public or private passwords. Exporting a PKCS #12 file creates this and you must provide it to decrypt the contents when you import the file into the Zyxel Device.
Page 157: My Certificates
Chapter 16 Certificates 16.2 My Certificates Click Configuration > Object > Certificate > My Certificates to open this screen. This is the Zyxel Device’s summary list of certificates and certification requests. Figure 94 Configuration > Object > Certificate > My Certificates The following table describes the labels in this screen.
Page 158: Add My Certificates
Chapter 16 Certificates Table 68 Configuration > Object > Certificate > My Certificates (continued) LABEL DESCRIPTION Issuer This field displays identifying information about the certificate’s issuing certification authority, such as a common name, organizational unit or department, organization or company and country.
Page 159 Chapter 16 Certificates The following table describes the labels in this screen. Table 69 Configuration > Object > Certificate > My Certificates > Add LABEL DESCRIPTION Name Type a name to identify this certificate. You can use up to 31 alphanumeric and ;‘~!@#$%^&()_+[]{}’,.=- characters.
Page 160: Edit My Certificates
Chapter 16 Certificates Table 69 Configuration > Object > Certificate > My Certificates > Add (continued) LABEL DESCRIPTION Create a certification Select this to have the Zyxel Device generate a request for a certificate and apply to a request and enroll for certification authority for a certificate.
Page 161 Chapter 16 Certificates Figure 96 Configuration > Object > Certificate > My Certificates > Edit NWA/WAC/WAX Series User’s Guide...
Page 162 Chapter 16 Certificates The following table describes the labels in this screen. Table 70 Configuration > Object > Certificate > My Certificates > Edit LABEL DESCRIPTION Name This field displays the identifying name of this certificate. You can use up to 31 alphanumeric and ;‘~!@#$%^&()_+[]{}’,.=- characters.
Page 163: Import Certificates
Chapter 16 Certificates Table 70 Configuration > Object > Certificate > My Certificates > Edit LABEL DESCRIPTION MD5 Fingerprint This is the certificate’s message digest that the Zyxel Device calculated using the MD5 algorithm. SHA1 Fingerprint This is the certificate’s message digest that the Zyxel Device calculated using the SHA1 algorithm.
Page 164: Trusted Certificates
Chapter 16 Certificates Figure 97 Configuration > Object > Certificate > My Certificates > Import The following table describes the labels in this screen. Table 71 Configuration > Object > Certificate > My Certificates > Import LABEL DESCRIPTION File Path Type in the location of the file you want to upload in this field or click Browse to find it.
Page 165: Edit Trusted Certificates
Chapter 16 Certificates Figure 98 Configuration > Object > Certificate > Trusted Certificates The following table describes the labels in this screen. Table 72 Configuration > Object > Certificate > Trusted Certificates LABEL DESCRIPTION PKI Storage Space This bar displays the percentage of the Zyxel Device’s PKI storage space that is currently in use. in Use When the storage space is almost full, you should consider deleting expired or unnecessary certificates before adding more certificates.
Page 166 Chapter 16 Certificates authority. Figure 99 Configuration > Object > Certificate > Trusted Certificates > Edit NWA/WAC/WAX Series User’s Guide...
Page 167 Chapter 16 Certificates The following table describes the labels in this screen. Table 73 Configuration > Object > Certificate > Trusted Certificates > Edit LABEL DESCRIPTION Name This field displays the identifying name of this certificate. You can change the name. You can use up to 31 alphanumeric and ;‘~!@#$%^&()_+[]{}’,.=- characters.
Page 168: Import Trusted Certificates
Chapter 16 Certificates Table 73 Configuration > Object > Certificate > Trusted Certificates > Edit (continued) LABEL DESCRIPTION Valid From This field displays the date that the certificate becomes applicable. The text displays in red and includes a Not Yet Valid! message if the certificate has not yet become applicable. Valid To This field displays the date that the certificate expires.
Page 169: Technical Reference
Chapter 16 Certificates Figure 100 Configuration > Object > Certificate > Trusted Certificates > Import The following table describes the labels in this screen. Table 74 Configuration > Object > Certificate > Trusted Certificates > Import LABEL DESCRIPTION File Path Type in the location of the file you want to upload in this field or click Browse to find it.
Page 170: System
H A P T E R System 17.1 Overview Use the system screens to configure general Zyxel Device settings. 17.1.1 What You Can Do in this Chapter • The Host Name screen (Section 17.2 on page 170) configures a unique name for the Zyxel Device in your network.
Page 171: Power Mode
Chapter 17 System The following table describes the labels in this screen. Table 75 Configuration > System > Host Name LABEL DESCRIPTION System Name Choose a descriptive name to identify your Zyxel Device device. This name can be up to 64 alphanumeric characters long.
Page 172: Date And Time
Chapter 17 System 17.4 Date and Time For effective scheduling and logging, the Zyxel Device system time must be accurate. The Zyxel Device has a software mechanism to set the time manually or get the current time and date from an external server.
Page 173 Chapter 17 System Table 77 Configuration > System > Date/Time (continued) LABEL DESCRIPTION New Date This field displays the last updated date from the time server or the last date configured (yyyy-mm-dd) manually. When you set Time and Date Setup to Manual, enter the new date in this field and then click Apply.
Page 174: Pre-Defined Ntp Time Servers List
Chapter 17 System 17.4.1 Pre-defined NTP Time Servers List When you turn on the Zyxel Device for the first time, the date and time start at 2003-01-01 00:00:00. The Zyxel Device then attempts to synchronize with one of the following pre-defined list of Network Time Protocol (NTP) time servers.
Page 175: Www Overview
Chapter 17 System To get the Zyxel Device date and time from a time server: Click System > Date/Time. Select Get from Time Server under Time and Date Setup. Under Time Zone Setup, select your Time Zone from the list. Under Time and Date Setup, enter a Time Server Address.
Page 176: Https
Chapter 17 System 17.5.3 HTTPS You can set the Zyxel Device to use HTTP or HTTPS (HTTPS adds security) for Web Configurator sessions. HTTPS (HyperText Transfer Protocol over Secure Socket Layer, or HTTP over SSL) is a web protocol that encrypts and decrypts web pages.
Page 177: Https Example
Chapter 17 System Figure 107 Configuration > System > WWW > Service Control The following table describes the labels in this screen. Table 79 Configuration > System > WWW > Service Control LABEL DESCRIPTION HTTPS Enable Select the check box to allow or disallow the computer with the IP address that matches the IP address(es) in the Service Control table to access the Zyxel Device Web Configurator using secure HTTPs connections.
Page 178 Chapter 17 System 17.5.5.1 Google Chrome Warning Messages When you attempt to access the Zyxel Device HTTPS server, you will see the error message shown in the following screen. Figure 108 Security Alert Dialog Box (Google Chrome) Select Advanced > Proceed to 192.168.1.2 (unsafe) to proceed to the Web Configurator login screen. 17.5.5.2 Mozilla Firefox Warning Messages When you attempt to access the Zyxel Device HTTPS server, a Warning screen appears as shown in the following screen.
Page 179 Chapter 17 System Figure 109 Security Certificate 1 (Firefox) 17.5.5.3 Avoiding Browser Warning Messages Here are the main reasons your browser displays warnings about the Zyxel Device’s HTTPS server certificate and what you can do to avoid seeing the warnings: •...
Page 180 Chapter 17 System Figure 110 Trusted Certificates The CA sends you a package containing the CA’s trusted certificate(s), your personal certificate(s) and a password to install the personal certificate(s). 17.5.5.5 Installing a Personal Certificate You need a password in advance. The CA may issue the password or you may have to specify it during the enrollment.
Page 181 Chapter 17 System Enter the password given to you by the CA. Have the wizard determine where the certificate should be saved on your computer or select Place all certificates in the following store and choose a different location. NWA/WAC/WAX Series User’s Guide...
Page 182 Chapter 17 System Click Finish to complete the wizard and begin the import process. You should see the following screen when the certificate is correctly installed on your computer. 17.5.5.6 Using a Certificate When Accessing the Zyxel Device To access the Zyxel Device via HTTPS: NWA/WAC/WAX Series User’s Guide...
Page 183: Ssh
Chapter 17 System Enter ‘https://Zyxel Device IP Address/’ in your browser’s web address field. When Authenticate Client Certificates is selected on the Zyxel Device, the following screen asks you to select a personal certificate to send to the Zyxel Device. This screen displays even if you only have a single certificate as in the example.
Page 184: How Ssh Works
Chapter 17 System 17.6.1 How SSH Works The following figure is an example of how a secure connection is established between two remote hosts using SSH v1. Figure 112 How SSH v1 Works Example Host Identification The SSH client sends a connection request to the SSH server. The server identifies itself with a host key. The client encrypts a randomly generated session key with the host key and server key and sends the result back to the server.
Page 185: Ssh Implementation On The Zyxel Device
Chapter 17 System 17.6.2 SSH Implementation on the Zyxel Device Your Zyxel Device supports SSH versions 1 and 2 using RSA authentication and four encryption methods (AES, 3DES, Archfour, and Blowfish). The SSH server is implemented on the Zyxel Device for management using port 22 (by default).
Page 186: Examples Of Secure Telnet Using Ssh
Chapter 17 System 17.6.5 Examples of Secure Telnet Using SSH This section shows two examples using a command interface and a graphical interface SSH client program to remotely access the Zyxel Device. The configuration and connection steps are similar for most SSH client programs.
Page 187: Telnet
Chapter 17 System Figure 115 SSH Example 2: Test $ telnet 192.168.1.2 22 Trying 192.168.1.2... Connected to 192.168.1.2. Escape character is '^]'. SSH-1.5-1.0.0 Enter “ssh –2 192.168.1.2”. This command forces your computer to connect to the Zyxel Device using SSH version 1. If this is the first time you are connecting to the Zyxel Device using SSH, a message displays prompting you to save the host information of the Zyxel Device.
Page 188: Ftp
Chapter 17 System Table 81 Configuration > System > TELNET (continued) LABEL DESCRIPTION Apply Click Apply to save your changes back to the Zyxel Device. Reset Click Reset to return the screen to its last-saved settings. 17.8 FTP You can upload and download the Zyxel Device’s firmware and configuration files using FTP. To use this feature, your computer must have an FTP client.
Page 189: Snmp
Chapter 17 System 17.9 SNMP Simple Network Management Protocol is a protocol used for exchanging management information between network devices. Your Zyxel Device supports SNMP agent functionality, which allows a manager station to manage and monitor the Zyxel Device through the network. The Zyxel Device supports SNMP version one (SNMPv1), version two (SNMPv2c), and version three (SNMPv3).
Page 190: Supported Mibs
Chapter 17 System • Trap - Used by the agent to inform the manager of some events. 17.9.1 Supported MIBs The Zyxel Device supports MIB II that is defined in RFC-1213 and RFC-1215. The Zyxel Device also supports private MIBs (ZYXEL-ES-CAPWAP.MIB, ZYXEL-ES-COMMON.MIB, ZYXEL-ES-ZyXELAPMgmt.MIB, ZYXEL-ES- PROWLAN.MIB, ZYXEL-ES-RFMGMT.MIB, ZYXEL-ES-SMI.MIB, and ZYXEL-ES-WIRELESS.MIB) to collect information about CPU and memory usage and VPN total throughput.
Page 191: Adding Or Editing An Snmpv3 User Profile
Chapter 17 System The following table describes the labels in this screen. Table 84 Configuration > System > SNMP LABEL DESCRIPTION Enable Select the check box to allow or disallow users to access the Zyxel Device using SNMP. Server Port You may change the server port number for a service if needed, however you must use the same port number in order to use that service for remote management.
Page 192 Chapter 17 System Figure 121 Configuration > System > SNMP > Add The following table describes the labels in this screen. Table 85 Configuration > System > SNMP LABEL DESCRIPTION User Name Select the user name of the user account for which this SNMPv3 user profile is configured. Authentication Select the type of authentication the SNMPv3 user must use to connect to the Zyxel Device using this SNMPv3 user profile.
Page 193: Log And Report
H A P T E R Log and Report 18.1 Overview Use the system screens to configure daily reporting and log settings. 18.1.1 What You Can Do In this Chapter • The Email Daily Report screen (Section 18.2 on page 193) configures how and where to send daily reports and what reports to send.
Page 194 Chapter 18 Log and Report Figure 122 Configuration > Log & Report > Email Daily Report The following table describes the labels in this screen. Table 86 Configuration > Log & Report > Email Daily Report LABEL DESCRIPTION Enable Email Select this to send reports by e-mail every day.
Page 195: Log Setting
Chapter 18 Log and Report Table 86 Configuration > Log & Report > Email Daily Report (continued) LABEL DESCRIPTION SSL/TLS Select SSL/TLS to use Secure Sockets Layer (SSL) or Transport Layer Security (TLS) if you want Encryption encrypted communications between the mail server and the Zyxel Device. Select STARTTLS to upgrade a plain text connection to a secure connection using SSL/TLS.
Page 196: Log Setting Screen
Chapter 18 Log and Report Summary screen to edit this information for all logs at the same time. 18.3.1 Log Setting Screen To access this screen, click Configuration > Log & Report > Log Setting. Figure 123 Configuration > Log & Report > Log Setting The following table describes the labels in this screen.
Page 197: Edit System Log Settings
Chapter 18 Log and Report Table 87 Configuration > Log & Report > Log Setting (continued) LABEL DESCRIPTION Log Format This field displays the format of the log. Internal - system log; you can view the log on the View Log tab. VRPT/Syslog - Zyxel’s Vantage Report, syslog-compatible format.
Page 198 Chapter 18 Log and Report Figure 124 Configuration > Log & Report > Log Setting > Edit System Log Setting NWA/WAC/WAX Series User’s Guide...
Page 199 Chapter 18 Log and Report The following table describes the labels in this screen. Table 88 Configuration > Log & Report > Log Setting > Edit System Log Setting LABEL DESCRIPTION E-Mail Server 1/2 Active Select this to send log messages and alerts according to the information in this section. You specify what kinds of log messages are included in log information and what kinds of log messages are included in alerts in the Active Log and Alert section.
Page 200 Chapter 18 Log and Report Table 88 Configuration > Log & Report > Log Setting > Edit System Log Setting (continued) LABEL DESCRIPTION E-mail Server 1 Use the E-Mail Server 1 drop-down list to change the settings for e-mailing logs to e-mail server 1 for all log categories.
Page 201: Edit Remote Server
Chapter 18 Log and Report 18.3.3 Edit Remote Server This screen controls the settings for each log in the remote server (syslog). Select a remote server entry in the Log Setting screen and click the Edit icon. Figure 125 Configuration > Log & Report > Log Setting > Edit Remote Server NWA/WAC/WAX Series User’s Guide...
Page 202: Active Log Summary
Chapter 18 Log and Report The following table describes the labels in this screen. Table 89 Configuration > Log & Report > Log Setting > Edit Remote Server LABEL DESCRIPTION Log Settings for Remote Server Active Select this check box to send log information according to the information in this section. You specify what kinds of messages are included in log information in the Active Log section.
Page 203 Chapter 18 Log and Report Figure 126 Active Log Summary This screen provides a different view and a different way of indicating which messages are included in each log and each alert. (The Default category includes debugging messages generated by open source software.) The following table describes the fields in this screen.
Page 204 Chapter 18 Log and Report Table 90 Configuration > Log & Report > Log Setting > Active Log Summary (continued) LABEL DESCRIPTION E-mail Server 1 Use the E-Mail Server 1 drop-down list to change the settings for e-mailing logs to e-mail server 1 for all log categories.
Page 205: File Manager
H A P T E R File Manager 19.1 Overview Configuration files define the Zyxel Device’s settings. Shell scripts are files of commands that you can store on the Zyxel Device and run when you need them. You can apply a configuration file or run a shell script without the Zyxel Device restarting.
Page 206: Configuration File
Chapter 19 File Manager While configuration files and shell scripts have the same syntax, the Zyxel Device applies configuration files differently than it runs shell scripts. This is explained below. Table 91 Configuration Files and Shell Scripts in the Zyxel Device Configuration Files (.conf) Shell Scripts (.zysh) •...
Page 207 Chapter 19 File Manager Once your Zyxel Device is configured and functioning properly, it is highly recommended that you back up your configuration file before making further configuration changes. The backup configuration file will be useful in case you need to return to your previous settings. Configuration File Flow at Restart •...
Page 208 Chapter 19 File Manager The following table describes the labels in this screen. Table 92 Maintenance > File Manager > Configuration File LABEL DESCRIPTION Rename Use this button to change the label of a configuration file on the Zyxel Device. You can only rename manually saved configuration files.
Page 209 Chapter 19 File Manager Table 92 Maintenance > File Manager > Configuration File (continued) LABEL DESCRIPTION Apply Use this button to have the Zyxel Device use a specific configuration file. Click a configuration file’s row to select it and click Apply to have the Zyxel Device use that configuration file.
Page 210: Example Of Configuration File Download Using Ftp
Chapter 19 File Manager Table 92 Maintenance > File Manager > Configuration File (continued) LABEL DESCRIPTION Last Modified This column displays the date and time that the individual configuration files were last changed or saved. Upload The bottom part of the screen allows you to upload a new or previously saved configuration file Configuration File from your computer to your Zyxel Device.
Page 211: Firmware Package
Chapter 19 File Manager C:\>ftp 192.168.1.2 Connected to 192.168.1.2. 220---------- Welcome to Pure-FTPd [privsep] [TLS] ---------- 220-You are user number 1 of 5 allowed. 220-Local time is now 21:28. Server port: 21. 220-This is a private system - No anonymous login 220 You will be disconnected after 600 minutes of inactivity.
Page 212: Example Of Firmware Upload Using Ftp
Chapter 19 File Manager Figure 129 Maintenance > File Manager > Firmware Package The following table describes the labels in this screen. Table 93 Maintenance > File Manager > Firmware Package LABEL DESCRIPTION Boot Module This is the version of the boot module that is currently on the Zyxel Device. Current Version This is the firmware version and the date created.
Page 213: Shell Script
Chapter 19 File Manager Use an FTP client on your computer to connect to the Zyxel Device. For example, in the Windows command prompt, type ftp 192.168.1.2. Keep the console session connected in order to see when the firmware recovery finishes. Enter your user name when prompted.
Page 214 Chapter 19 File Manager Figure 131 Maintenance > File Manager > Shell Script Each field is described in the following table. Table 94 Maintenance > File Manager > Shell Script LABEL DESCRIPTION Rename Use this button to change the label of a shell script file on the Zyxel Device. You cannot rename a shell script to the name of another shell script in the Zyxel Device.
Page 215 Chapter 19 File Manager Table 94 Maintenance > File Manager > Shell Script (continued) LABEL DESCRIPTION Browse... Click Browse... to find the .zysh file you want to upload. Upload Click Upload to begin the upload process. This process may take up to several minutes. NWA/WAC/WAX Series User’s Guide...
Page 216: Diagnostics
H A P T E R Diagnostics 20.1 Overview Use the diagnostics screen for troubleshooting. 20.1.1 What You Can Do in this Chapter The Diagnostics screen (Section 20.2 on page 216) generates a file containing the Zyxel Device’s configuration and diagnostic information if you need to provide it to customer support during troubleshooting.
Page 217 Chapter 20 Diagnostics Figure 133 Maintenance > Diagnostics: Debug Information Collector NWA/WAC/WAX Series User’s Guide...
Page 218: Leds
H A P T E R LEDs 21.1 Overview The LEDs of your Zyxel Device can be controlled such that they stay lit (ON) or OFF after the Zyxel Device is ready. There are two features that control the LEDs of your Zyxel Device - Locator and Suppression (see Section 1.4 on page 19).
Page 219: Locator Screen
Chapter 21 LEDs Figure 134 Maintenance > LEDs > Suppression The following table describes fields in the above screen. Table 95 Maintenance > LED > Suppression LABEL DESCRIPTION Suppression On If the Suppression On check box is checked, the LEDs of your Zyxel Device will turn off after it’s ready.
Page 220 Chapter 21 LEDs Figure 135 Maintenance > LEDs > Locator The following table describes fields in the above screen. Table 96 Maintenance > LED > Locator LABEL DESCRIPTION Turn On Click Turn On button to activate the locator. The Locator function will show the actual location of the Zyxel Device between several devices in the network.
Page 221: Antenna Switch
H A P T E R Antenna Switch 22.1 Overview Use this screen to adjust coverage depending on the orientation of the antenna. 22.1.1 What You Need To Know Positioning the antennas properly increases the range and coverage area of a wireless LAN. On the Zyxel Device that comes with internal antennas and also has an antenna switch, you can adjust coverage depending on the antenna orientation for the Zyxel Device radios using the web configurator, the command line interface (CLI) or a physical switch.
Page 222 Chapter 22 Antenna Switch Figure 137 Maintenance > Antenna > Antenna Switch (Per Radio) Figure 138 Maintenance > Antenna > Antenna Switch (Per AP) If the Zyxel Device has a physical antenna switch, select the Enable Software Control option to use the Web Configurator to adjust coverage depending on each radio’s antenna orientation for better coverage.
Page 223: Reboot
H A P T E R Reboot 23.1 Overview Use this screen to restart the Zyxel Device. 23.1.1 What You Need To Know If you applied changes in the Web Configurator, these were saved automatically and do not change when you reboot. If you made changes in the CLI, however, you have to use the write command to save the configuration before you reboot.
Page 224: Shutdown
H A P T E R Shutdown 24.1 Overview Use this screen to shut down the Zyxel Device. Always use Maintenance > Shutdown > Shutdown or the shutdown command before you turn off the Zyxel Device or remove the power. Not doing so can cause the firmware to become corrupt.
Page 225: Local Configuration In Cloud Mode
Local Configuration in Cloud Mode...
Page 226: Cloud Mode
H A P T E R Cloud Mode 25.1 Overview The Zyxel Device is managed and provisioned automatically by the NCC (Nebula Control Center) when it is connected to the Internet and has been registered in the NCC. If you need to change the Zyxel Device’s VLAN setting or manually set its IP address, access its simplified web configurator (see Chapter 4 on page...
Page 227 Chapter 25 Cloud Mode • Maintenance > Log These screens also have fewer options than those in standalone Zyxel Devices. The rest of the Zyxel Device’s features must be configured through the NCC. NWA/WAC/WAX Series User’s Guide...
Page 228: Dashboard
H A P T E R Dashboard This screen displays general AP information, and client information in widgets that you can re-arrange to suit your needs. You can also collapse, refresh, and close individual widgets. Figure 141 Dashboard The following table describes the labels in this screen. Table 97 Dashboard LABEL DESCRIPTION...
Page 229 Chapter 26 Dashboard Table 97 Dashboard (continued) LABEL DESCRIPTION Nebula Control This field displays whether the Zyxel Device has been registered and can be managed by Center the NCC. Activation Status Use Proxy to This displays whether the NAP uses a proxy server to access the NCC (Nebula Control Access NCC Center).
Page 230: Network
H A P T E R Network 27.1 Overview This chapter describes how you can configure the management IP address and VLAN settings of your Zyxel Device in cloud mode. Section 9.1 on page 94 for information about IP addresses. Note: Make sure your VLAN settings allow the Zyxel Device to connect to the Internet so you could manage it with NCC.
Page 231 Chapter 27 Network Figure 142 Configuration > Network > IP Setting Each field is described in the following table. Table 98 Configuration > Network > IP Setting LABEL DESCRIPTION IP Address Assignment Select this to make the interface a DHCP client and automatically get the IP address, Automatically subnet mask, and gateway address from a DHCP server.
Page 232: Vlan
Chapter 27 Network 27.3 VLAN This section discusses how to configure the Zyxel Device’s VLAN settings. See Section 9.3 on page 98 more information about VLAN. Use this screen to configure the VLAN settings for your Zyxel Device. To access this screen, click Configuration >...
Page 233: Maintenance
H A P T E R Maintenance 28.1 Overview When the Zyxel Device is set to work in cloud mode, the Maintenance screens let you mange shell script files on the Zyxel Device, generate a diagnostic file, or view log messages. Chapter 19 on page 205 for information about shell scripts.
Page 234: Diagnostics
Chapter 28 Maintenance Each field is described in the following table. Table 100 Maintenance > Shell Script LABEL DESCRIPTION Rename Use this button to change the label of a shell script file on the Zyxel Device. You cannot rename a shell script to the name of another shell script in the Zyxel Device. Click a shell script’s row to select it and click Rename to open the Rename File screen.
Page 235: View Log
Chapter 28 Maintenance Figure 145 Maintenance > Diagnostics The Debug Information Center screen then displays showing whether the collection is in progress, was successful, or has failed. When the data collection is done, click Download to save the most recent diagnostic file to a computer.
Page 236 Chapter 28 Maintenance Figure 147 Maintenance > Log > View Log The following table describes the labels in this screen. Table 101 Maintenance > Log > View Log LABEL DESCRIPTION Show Filter / Hide Click this button to show or hide the filter settings. Filter If the filter settings are hidden, the Display, Email Log Now, Refresh, and Clear Log fields are available.
Page 237 Chapter 28 Maintenance Table 101 Maintenance > Log > View Log (continued) LABEL DESCRIPTION Refresh Click this to update the list of logs. Clear Log Click this button to clear the whole log, regardless of what is currently displayed on the screen. This field is a sequential value, and it is not associated with a specific log message.
Page 238: Appendices And Troubleshooting
Appendices and Troubleshooting...
Page 239: Troubleshooting
H A P T E R Troubleshooting 29.1 Overview This chapter offers some suggestions to solve problems you might encounter. The potential problems are divided into the following categories. • Power, Hardware Connections, and LED • Zyxel Device Management, Access, and Login •...
Page 240: Zyxel Device Management, Access, And Login
Chapter 29 Troubleshooting Disconnect and re-connect the power adapter or PoE power injector to the Zyxel Device. If the problem continues, contact the vendor. 29.3 Zyxel Device Management, Access, and Login I forgot the IP address for the Zyxel Device. The default in-band IP address in standalone mode is http://DHCP-assigned IP (when connecting to a DHCP server) or 192.168.1.2.
Page 241 Chapter 29 Troubleshooting If the problem continues, contact the network administrator or vendor, or try one of the advanced suggestions. Advanced Suggestions • Try to access the Zyxel Device using another service, such as Telnet. If you can access the Zyxel Device, check the remote management settings to find out why the Zyxel Device does not respond to HTTP.
Page 242 Chapter 29 Troubleshooting I enabled NCC Discovery, but the Zyxel Device is still in standalone mode. Make sure your Zyxel Device is registered to the NCC. The Zyxel Device is already registered with NCC, but it is still in standalone mode; it cannot connect to the NCC.
Page 243 Chapter 29 Troubleshooting Make sure that the Zyxel Device and the AC are both in the same subnet. If you have to set them up in different subnets, see AC management and IP Subnets on page I accidentally pressed the Nebula button in the NXC’s Web Configurator. How do I undo it? If the Zyxel Device is not registered with the NCC, register it first.
Page 244: Internet Access
Chapter 29 Troubleshooting I cannot upload the firmware uploaded using FTP. The Web Configurator is the recommended method for uploading firmware in standalone mode. For managed Zyxel Devices, using the NCC or AC is recommended. You only need to use FTP if you need to recover the firmware.
Page 245: Wifi Network
Chapter 29 Troubleshooting If the problem continues, contact the network administrator or vendor. 29.5 WiFi Network I cannot access the Zyxel Device or ping any computer from the WLAN. Make sure the wireless LAN (wireless radio) is enabled on the Zyxel Device. Make sure the radio or at least one of the Zyxel Device’s radios is operating in AP mode.
Page 246: Resetting The Zyxel Device
Chapter 29 Troubleshooting Any certificate that you want to import has to be in one of these file formats: • Binary X.509: This is an ITU-T recommendation that defines the formats for X.509 certificates. • PEM (Base-64) encoded X.509: This Privacy Enhanced Mail format uses lowercase letters, uppercase letters and numerals to convert a binary X.509 certificate into a printable form.
Page 247: Getting More Troubleshooting Help
Chapter 29 Troubleshooting Note: This procedure removes the current configuration. Make sure the Power LED is on and not blinking. Press the RESET button and hold it until the Power LED begins to blink. (This usually takes about ten seconds.) Release the RESET button, and wait for the Zyxel Device to restart.
Page 248: Appendix A Importing Certificates
P P E N D I X Importing Certificates This appendix shows you how to import public key certificates into your web browser. Public key certificates are used by web browsers to ensure that a secure web site is legitimate. When a certificate authority such as VeriSign, Comodo, or Network Solutions, to name a few, receives a certificate request from a website operator, they confirm that the web domain and contact information in the request match those on public record with a domain name registrar.
Page 249 Appendix A Importing Certificates Export a Certificate If your device’s Web Configurator is set to use SSL certification, then upon browsing with it for the first time, you are presented with a certification error. NWA/WAC/WAX Series User’s Guide...
Page 250 Appendix A Importing Certificates Click Advanced > Proceed to x.x.x.x (unsafe). In the Address Bar, click Not Secure > Certificate (Invalid). NWA/WAC/WAX Series User’s Guide...
Page 251 Appendix A Importing Certificates In the Certificate dialog box, click Details > Copy to File. In the Certificate Export Wizard, click Next. NWA/WAC/WAX Series User’s Guide...
Page 252 Appendix A Importing Certificates Select the format and settings you want to use and then click Next. Type a filename and specify a folder to save the certificate in. Click Next. NWA/WAC/WAX Series User’s Guide...
Page 253 Appendix A Importing Certificates In the Completing the Certificate Export Wizard screen, click Finish. Finally, click OK when presented with the successful certificate export message. Import a Certificate After storing the certificate in your computer (see Export a Certificate), you need to install it as a trusted root certification authority using the following steps: NWA/WAC/WAX Series User’s Guide...
Page 254 Appendix A Importing Certificates Open your web browser, click the menu icon, and click Settings. NWA/WAC/WAX Series User’s Guide...
Page 255 Appendix A Importing Certificates Scroll down and click Advanced to expand the menu. Under Privacy and security, click Manage certificates. NWA/WAC/WAX Series User’s Guide...
Page 256 Appendix A Importing Certificates In the Certificates pop-up screen, click Trusted Root Certification Authorities. Click Import to start the Certificate Import Wizard. Click Next when the wizard pops up, and then on the following screen click Browse. NWA/WAC/WAX Series User’s Guide...
Page 257 Appendix A Importing Certificates Select the certificate file you want to import and click Open. Click Next. NWA/WAC/WAX Series User’s Guide...
Page 258 Appendix A Importing Certificates Confirm the settings displayed and click Finish. If presented with a security warning, click Yes. NWA/WAC/WAX Series User’s Guide...
Page 259 Appendix A Importing Certificates Finally, click OK when you are notified of the successful import. Install a Stand-Alone Certificate File Rather than installing a public key certificate using web browser settings, you can install a stand-alone certificate file if one has been issued to you. Double-click the public key certificate file.
Page 260 Appendix A Importing Certificates Click Next on the first wizard screen, click Place all certificates in the following store, and click Browse. Select Trusted Root Certificate Authorities > OK, and then click Next. NWA/WAC/WAX Series User’s Guide...
Page 261 Appendix A Importing Certificates Confirm the information shown on the final wizard screen and click Finish. If presented with a security warning, click Yes. NWA/WAC/WAX Series User’s Guide...
Page 262 Appendix A Importing Certificates Finally, click OK when you are notified of the successful import. Remove a Certificate in Google Chrome This section shows you how to remove a public key certificate in Google Chrome on Windows 7. Open your web browser, click the menu icon, and click Settings. NWA/WAC/WAX Series User’s Guide...
Page 263 Appendix A Importing Certificates Scroll down and click Advanced to expand the menu. Under Privacy and security, click Manage certificates. In the Certificates pop-up screen, click Trusted Root Certification Authorities. NWA/WAC/WAX Series User’s Guide...
Page 264 Appendix A Importing Certificates Select the certificate you want to remove and click Remove. Click Yes when you see the following warning message. Confirm the details displayed in the warning message and click Yes. Firefox The following example uses Mozilla Firefox on Windows 7. You first have to store the certificate in your computer and then install it as a Trusted Root CA, as shown in the following tutorials.
Page 265 Appendix A Importing Certificates Export a Certificate If your device’s Web Configurator is set to use SSL certification, then the first time you browse to it you are presented with a certification error. Click Advanced. Click View Certificate. NWA/WAC/WAX Series User’s Guide...
Page 266 Appendix A Importing Certificates Click Details > Export. Type a filename and click Save. Import a Certificate After storing the certificate in your computer, you need to import it in trusted root certification authorities using the following steps: NWA/WAC/WAX Series User’s Guide...
Page 267 Appendix A Importing Certificates Open Firefox and click Tools > Options. NWA/WAC/WAX Series User’s Guide...
Page 268 Appendix A Importing Certificates In the Options page, click Privacy & Security, scroll to the bottom of the page, and then click View Certificates. In the Certificate Manager, click Authorities > Import. NWA/WAC/WAX Series User’s Guide...
Page 269 Appendix A Importing Certificates Use the Select File dialog box to locate the certificate and then click Open. Select Trust this CA to identify websites and click OK. Removing a Certificate in Firefox This section shows you how to remove a public key certificate in Firefox. NWA/WAC/WAX Series User’s Guide...
Page 270 Appendix A Importing Certificates Open Firefox and click Tools > Options. In the Options page, click Privacy & Security, scroll to the bottom of the page, and then click View Certificates. NWA/WAC/WAX Series User’s Guide...
Page 271 Appendix A Importing Certificates In the Certificate Manager, click Authorities and select the certificate you want to remove. Click Delete or Distrust. In the following dialog box, click OK. The next time you go to the web site that issued the public key certificate you just removed, a certification error appears.
Page 272: Appendix B Ipv6
P P E N D I X IPv6 Overview IPv6 (Internet Protocol version 6), is designed to enhance IP address size and features. The increase in IPv6 address size to 128 bits (from the 32-bit IPv4 address) allows up to 3.4 x 10 IP addresses.
Page 273 Appendix B IPv6 Unspecified Address An unspecified address (0:0:0:0:0:0:0:0 or ::) is used as the source address when a device does not have its own address. It is similar to “0.0.0.0” in IPv4. Loopback Address A loopback address (0:0:0:0:0:0:0:1 or ::1) allows a host to send packets to itself. It is similar to “127.0.0.1” in IPv4.
Page 274 Appendix B IPv6 Subnet Masking Both an IPv6 address and IPv6 subnet mask compose of 128-bit binary digits, which are divided into eight 16-bit blocks and written in hexadecimal notation. Hexadecimal uses four bits for each character (1 ~ 10, A ~ F). Each block’s 16 bits are then represented by four hexadecimal characters. For example, FFFF:FFFF:FFFF:FFFF:FC00:0000:0000:0000.
Page 275 Appendix B IPv6 Each DHCP client and server has a unique DHCP Unique IDentifier (DUID), which is used for identification when they are exchanging DHCPv6 messages. The DUID is generated from the MAC address, time, vendor assigned ID and/or the vendor's private enterprise number registered with the IANA. It should not change over time even after you reboot the device.
Page 276 Appendix B IPv6 ICMPv6 Internet Control Message Protocol for IPv6 (ICMPv6 or ICMP for IPv6) is defined in RFC 4443. ICMPv6 has a preceding Next Header value of 58, which is different from the value used to identify ICMP for IPv4. ICMPv6 is an integral part of IPv6.
Page 277 Appendix B IPv6 multicast packets and the IP addresses of multicast groups the hosts want to join on its network. MLD snooping and MLD proxy are analogous to IGMP snooping and IGMP proxy in IPv4. MLD filtering controls which multicast groups a port can join. MLD Messages A multicast router or switch periodically sends general queries to MLD hosts to update the multicast forwarding table.
Page 278 Appendix B IPv6 Install Dibbler and select the DHCPv6 client option on your computer. After the installation is complete, select Start > All Programs > Dibbler-DHCPv6 > Client Install as service. Select Start > Control Panel > Administrative Tools > Services. Double click Dibbler - a DHCPv6 client.
Page 279 Appendix B IPv6 Select Control Panel > Network and Sharing Center > Local Area Connection. Select the Internet Protocol Version 6 (TCP/IPv6) checkbox to enable it. Click OK to save the change. Click Close to exit the Local Area Connection Status screen. Select Start >...
Page 280: Appendix C Customer Support
• Brief description of the problem and the steps you took to solve it. Corporate Headquarters (Worldwide) Taiwan • Zyxel Communications Corporation • http://www.zyxel.com Asia China • Zyxel Communications (Shanghai) Corp. Zyxel Communications (Beijing) Corp. Zyxel Communications (Tianjin) Corp. • https://www.zyxel.com/cn/zh/ India • Zyxel Technology India Pvt Ltd • https://www.zyxel.com/in/en/ Kazakhstan •...
Page 281 • Zyxel Singapore Pte Ltd. • http://www.zyxel.com.sg Taiwan • Zyxel Communications Corporation • https://www.zyxel.com/tw/zh/ Thailand • Zyxel Thailand Co., Ltd • https://www.zyxel.com/th/th/ Vietnam • Zyxel Communications Corporation-Vietnam Office • https://www.zyxel.com/vn/vi Europe Belarus • Zyxel BY • https://www.zyxel.by Belgium • Zyxel Communications B.V. • https://www.zyxel.com/be/nl/...
Page 282 Appendix C Customer Support • https://www.zyxel.com/be/fr/ Bulgaria • Zyxel България • https://www.zyxel.com/bg/bg/ Czech Republic • Zyxel Communications Czech s.r.o • https://www.zyxel.com/cz/cs/ Denmark • Zyxel Communications A/S • https://www.zyxel.com/dk/da/ Estonia • Zyxel Estonia • https://www.zyxel.com/ee/et/ Finland • Zyxel Communications • https://www.zyxel.com/fi/fi/ France •...
Page 283 • Zyxel Communications Poland • https://www.zyxel.com/pl/pl/ Romania • Zyxel Romania • https://www.zyxel.com/ro/ro Russia • Zyxel Russia • https://www.zyxel.com/ru/ru/ Slovakia • Zyxel Communications Czech s.r.o. organizacna zlozka • https://www.zyxel.com/sk/sk/ Spain • Zyxel Communications ES Ltd • https://www.zyxel.com/es/es/ Sweden • Zyxel Communications • https://www.zyxel.com/se/sv/ Switzerland •...
Page 284 Appendix C Customer Support Turkey • Zyxel Turkey A.S. • https://www.zyxel.com/tr/tr/ • Zyxel Communications UK Ltd. • https://www.zyxel.com/uk/en/ Ukraine • Zyxel Ukraine • http://www.ua.zyxel.com South America Argentina • Zyxel Communications Corporation • https://www.zyxel.com/co/es/ Brazil • Zyxel Communications Brasil Ltda. • https://www.zyxel.com/br/pt/ Colombia •...
Page 285 Appendix C Customer Support Middle East • Zyxel Communications Corporation • https://www.zyxel.com/me/en/ North America • Zyxel Communications, Inc. - North America Headquarters • https://www.zyxel.com/us/en/ Oceania Australia • Zyxel Communications Corporation • https://www.zyxel.com/au/en/ Africa South Africa • Nology (Pty) Ltd. • https://www.zyxel.com/za/en/...
Page 286: Appendix D Legal Information
The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of Zyxel Communications Corporation. Published by Zyxel Communications Corporation. All rights reserved.
Page 287 Appendix D Legal Information CANADA The following information applies if you use the product within Canada area. Innovation, Science and Economic Development Canada ICES Statement CAN ICES-3 (B)/NMB-3(B) Innovation, Science and Economic Development Canada RSS-GEN & RSS-247 Statement • This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s).
Page 288 Appendix D Legal Information Antenna Information ANTENNA MODEL TYPE CONNECTOR 2.4 G GAIN 5G GAIN REMARK NWA1123-ACv2 PIFA 3.08 PIFA 3.07 PIFA 4.06 (5150~5250 MHz) 3.79 (5725~5850 MHz) PIFA 3.99 (5150~5250 MHz) 3.78 (5725~5850 MHz) NWA1123-AC HD PIFA I-PEX 3 (2400-2483.5 MHz) PIFA I-PEX 3 (2400-2483.5 MHz)
Page 289 Appendix D Legal Information ANTENNA MODEL TYPE CONNECTOR 2.4 G GAIN 5G GAIN REMARK WAC5302D-S Loop I-PEX 5.82 (2400-2483.5 MHz) Loop I-PEX 5.02 (2400-2483.5 MHz) PIFA I-PEX 5 (5150-5250 MHz) 5 (5250-5350 MHz) 5 (5470-5725 MHz) 5 (5725-5850 MHz) WAC6303D-S Direction U.FL 1.12 (2400-2483.5 MHz)
Page 290 Appendix D Legal Information Informations Antenne MODÈLE D'ANTENNE TYPE CONNECTEUR 2.4 G GAIN 5G GAIN REMARQUE NWA1123-ACv2 PIFA 3.08 PIFA 3.07 PIFA 4.06 (5150~5250 MHz) 3.79 (5725~5850 MHz) PIFA 3.99 (5150~5250 MHz) 3.78 (5725~5850 MHz) NWA1123-AC HD PIFA I-PEX 3 (2400-2483.5 MHz) PIFA I-PEX 3 (2400-2483.5 MHz)
Page 291 Appendix D Legal Information MODÈLE D'ANTENNE TYPE CONNECTEUR 2.4 G GAIN 5G GAIN REMARQUE WAC5302D-S Loop I-PEX 5.82 (2400-2483.5 MHz) Loop I-PEX 5.02 (2400-2483.5 MHz) PIFA I-PEX 5 (5150-5250 MHz) 5 (5250-5350 MHz) 5 (5470-5725 MHz) 5 (5725-5850 MHz) WAC6303D-S Direction U.FL 1.12 (2400-2483.5 MHz)
Page 292 Appendix D Legal Information Avertissement: (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.;...
Page 293 Appendix D Legal Information • The band 5,470 MHz to 5,725 MHz is 914.11 mW. WAX650S • The band 2,400 MHz to 2,483.5 MHz is 91.2 mW, • The band 5,150 MHz to 5,350 MHz is 177.01 mW, • The band 5,470 MHz to 5,725 MHz is 899.5 mW. WAX510D and NWA110AX •...
Page 294 Appendix D Legal Information Malti (Maltese) Hawnhekk, Zyxel, jiddikjara li dan tagħmir jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 2014/53/EU. Nederlands Hierbij verklaart Zyxel dat het toestel uitrusting in overeenstemming is met de essentiële eisen en de andere relevante (Dutch) bepalingen van richtlijn 2014/53/EU.
Page 295 Appendix D Legal Information External antenna Use only the antennas which have been approved by Zyxel Communications Corporation. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC/IC limit and is prohibited.
Page 296 Appendix D Legal Information European Union - Disposal and Recycling Information The symbol below means that according to local regulations your product and/or its battery shall be disposed of separately from domestic waste. If this product is end of life, take it to a recycling station designated by local authorities. At the time of disposal, the separate collection of your product and/or its battery will help save natural resources and ensure that the environment is sustainable development.
Page 297 Appendix D Legal Information 無線資訊傳輸設備必須具備安全功能，以保護未經授權之一方任意更改軟體進而避免發射機操作於非經認證之頻率、輸出功率、調變形式或其他射頻參數設定。使用無線產品時，應避免影響附近雷達系統之操作。高增益指向性天線只得應用於固定式點對點系統。專業安裝警語： (WAC6553D-E) 以下訊息僅適用於產品屬於專業安裝並銷售至台灣地區本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者。安全警告為了您的安全，請先閱讀以下警告及指示 : • 請勿將此產品接近水、火焰或放置在高溫的環境。 • 避免設備接觸任何液體 - 切勿讓設備接觸水、雨水、高濕度、污水腐蝕性的液體或其他水份。 • 灰塵及污物 - 切勿接觸灰塵、污物、沙土、食物或其他不合適的材料。 • 雷雨天氣時，不要安裝，使用或維修此設備。有遭受電擊的風險。 • 切勿重摔或撞擊設備，並勿使用不正確的電源變壓器。 • 若接上不正確的電源變壓器會有爆炸的風險。 • 請勿隨意更換產品內的電池。 • 如果更換不正確之電池型式，會有爆炸的風險，請依製造商說明書處理使用過之電池。 • 請將廢電池丟棄在適當的電器或電子設備回收處。 • 請勿將設備解體。 • 請勿阻礙設備的散熱孔，空氣對流不足將會造成設備損害。 •...
Page 298 Appendix D Legal Information proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value, and will be solely at the discretion of Zyxel. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions.
Page 299: Index
Index Index Symbols advertising settings Bluetooth Low Energy 20, 22, 23, 119 Bluetooth Smart iBeacon iBeacon ID Numbers major minor UUID 802.11k 20, 22, 23 UUID format 802.11r 20, 22, 23 boot module 802.11v 20, 22, 23 AC. See AP Controller access and certificates access privileges...
Page 300 Index serial number 162, 167 storage space 157, 165 thumbprint algorithms date thumbprints daylight savings used for authentication verifying fingerprints DHCP certification requests 159, 160 and domain name certifications diagnostics 216, 234 viewing disclaimer channel domain name 32, 57 dual radios button messages dual-radio application...
Page 301 Index prefix length stateless autoconfiguration unspecified address Guide CLI Reference Java permissions HTTP JavaScripts over SSL, see HTTPS redirect to HTTPS vs HTTPS HTTPS and certificates authenticating clients key pairs avoiding warning messages example vs HTTP with Internet Explorer with Netscape Navigator HyperText Transfer Protocol over Secure Socket Layer, lastgood.conf 207, 209...
Page 302 Index power off power on product registration MAC address range Public-Key Infrastructure (PKI) Management Information Base (MIB) 189, 190 public-private key pairs Management Mode CAPWAP and DHCP management mode Management, NCC Management, Standalone radio managing the device Radio Frequency monitor good habits reboot 65, 223...
Page 303 Index service control present at restart and users startup-config-bad.conf limitations station timeouts statistics Service Set daily e-mail report Service Set Identifier status see SSID stopping the device shell scripts supported browsers downloading 214, 234 syslog 197, 202 editing 213, 233 syslog servers, see also logs how applied system log, see logs...
Page 304 Index user objects layer-2 isolation MAC filtering users radio access, see also access users security admin (type) SSID admin, see also admin users and service control wireless security 17, 245 currently logged in wireless station default lease time 126, 128 Wizard Setup default reauthentication time 126, 128...

This manual is also suitable for:

Wac series Wax series Nwa110ax eu0103f Nwa1123-acv2 Nwa1123-ac pro Nwa1123-ac hd ... Show all

ZyXEL Communications NWA Seres User Manual

Chapter 1 Introduction

Chapter 2 AP Management

Chapter 3 Hardware

Chapter 4 Web Configurator

Chapter 6 Dashboard

Chapter 7 Setup Wizard

Chapter 8 Monitor

Chapter 9 Network

Chapter 10 Wireless

Chapter 11 Bluetooth

Chapter 12 User

Chapter 13 AP Profile

Chapter 14 MON Profile

Chapter 15 WDS Profile

Chapter 16 Certificates

Chapter 18 Log and Report

Chapter 19 File Manager

Chapter 20 Diagnostics

Chapter 21 Leds

Chapter 22 Antenna Switch

Chapter 23 Reboot

Chapter 24 Shutdown

Chapter 25 Cloud Mode

Chapter 26 Dashboard

Chapter 27 Network

Chapter 28 Maintenance

Chapter 29 Troubleshooting

Appendix A Importing Certificates

Appendix B Ipv6

Appendix C Customer Support

Appendix D Legal Information

Quick Links

Troubleshooting

Related Manuals for ZyXEL Communications NWA Seres

Summary of Contents for ZyXEL Communications NWA Seres