Related Manuals for Neilsen CT1405
Summary of Contents for Neilsen CT1405
- Page 1 AIR NIBBLER CT1405 ORIGINAL INSTRUCTIONS Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: AIR NIBBLER Model: CT1405 Applicable EC Directives: EC Machinery Directive 2006/42/EC Harmonized standards EN ISO 11148-11 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. -
Page 3: Specifications
SPECIFICATIONS Max. air pressure: 6.2bar(90PSI) Speed: 3500/min Avg. air consumption: 6cfm Max. cutting Capacity: 1.5mm Air inlet:1/4" IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING - When using tools, basic precautions should always be followed, including the following: Work area a) Keep the work area clean and well lighted. - Page 4 b) When servicing a tool, use only identical replacement parts. Use only authorized parts. c) Use only the lubricants specified by the manufacturer. Air Supply 1. Incorporate a filter, regulator with pressure gauge, oiler, in-line shutoff valve, and quick coupler for best service, as shown on Figure A and Figure B, An in-line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured.
- Page 5 6. Inspect the air connections for leaks. Repair any leaks found. 8. If the tool will not be used at this time, turn off and detach the air supply, safely discharge any residual air pressure, and release the throttle and/or turn the switch to its off position to prevent accidental operation.
- Page 6 Figure B: Stationary Air Supply Setup Description Function Vibration Pads For noise and vibration reduction Anchor Bolts Secures air compressor in place Ball Valve Isolates sections of system for maintenance Isolation Hose For vibration reduction Main Air Line - 3/4" minimum Distributes air to branch lines recommended Ball Valve...
- Page 7 GENERAL OPERATING INSTRUCTIONS 1. If an automatic oiler is not used, add a few drops of pneumatic tool oil to the airline connection and space between Cutter (30) and Die (32) before use. Add a few drops more after each hour of continual use. 2.
-
Page 8: Cleaning, Maintenance And Lubrication
CLEANING, MAINTENANCE AND LUBRICATION Note: These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the air-operated tool. 2. Periodically, 1. Daily - Air Supply Maintenance: Every inspect the day, maintain the air supply according to the condition of the component manufacturers' instructions. - Page 9 SYMBOLS In this manual and/or on the machine the following symbols are used: Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual. Wear hearing protection. Wear safety goggles. Contact with or inhalation of dust coming free during use (e.g.
-
Page 10: Assembly Diagram
ASSEMBLY DIAGRAM... -
Page 11: Assembly Diagram And Parts List
ASSEMBLY DIAGRAM AND PARTS LIST Part Description Part Description Washer Air Inlet Bushing Gear Case Throttle Lever Idler Gear Handle Pin Rear Spindle Handle Pin Idler Gear Pin O-Ring Keeper Nibbler Head O-Ring Pushing Rod Bushing Valve Stem Pushing Rod Valve Ball Cutter Spring... - Page 12 Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. Made in China...