Table of Contents
Related Manuals for Neilsen CT1091
Summary of Contents for Neilsen CT1091
- Page 1 33 PIECE AIR TOOL KIT CT1091 ORIGINAL INSTRUCTIONS Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
-
Page 2: Ec Declaration Of Conformity
EC Directive based on its design and type, as brought into circulation by In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: 1/4”DRIVE AIR DIE GRINDER Model: CT1091-1 Applicable EC Directives: EC Machinery Directive 2006/42/EC... -
Page 3: Specification
1. SPECIFICATION This tool kit includes: 1pc 1/2"Dr air impact wrench 1pc 1/ 2"Dr air ratchet wrench 1pc 1/ 4"Dr air die grinder 1pc 150mm air hammer 1pc air hammer spring 10pcs air sockets: 9, 10, 11, 13, 14, 17, 19, 22, 24 and 27mm 5pcs 1/4"... -
Page 4: Safety Instructions
2. SAFETY INSTRUCTIONS WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment. WARNING! Disconnect from the air supply before changing accessories, servicing or performing any maintenance. Maintain the tools in good condition (use an authorised service agent). ... - Page 5 3. PREPERATION FOR USE Recommended hook-up is shown in fig.1. WARNING! Ensure that the air supply is clean and does not exceed 90 psi while operating these tools. Too much air pressure and/or unclean air will cause excessive wear and may be dangerous, causing damage and/or personal injury.
- Page 6 DO NOT turn the die grinder on whilst the grinding bit is in contact with the workpiece. DO NOT use die grinder where there are flammable liquids, solids or gases such as paint solvents, including waste wiping or cleaning rags etc. as generated sparks may be dangerous.
- Page 7 B until the spring is fully located (fig.4) and the chisel is retained by the spring’s retaining tag (B). c. Connect the hammer to the air supply as in Section 4. d. To operate the hammer, squeeze the trigger, taking care that the chisel end is not in contact with the work-piece.
-
Page 8: Maintenance
5. MAINTENANCE WARNING! Disconnect the tool from the air supply before changing accessories, servicing or performing maintenance. Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 9.1. If the air supply does not have an oiler, lubricate the air tool daily with a few drops of air tool oil dripped into the air inlet to prolong its life. - Page 9 7. SYMBOLS In this manual and/or on the machine the following symbols are used: Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual. Wear hearing protection. Wear safety goggles.
-
Page 10: Assembly Diagram And Parts List
8. ASSEMBLY DIAGRAM AND PARTS LIST 1/4” Drive Air Die Grinder... - Page 11 1/2" Drive Air Ratchet Wrench...
- Page 12 150mm Air Hammer...
- Page 13 1/2" Drive Air Impact Wrench Parts No. Description Quantity Parts No. Description Quantity Protecting Rubber Washer Housing Screw Screw Rubber Anvil Bushing Screw Anvil Collar and Seal Exhaust Deflector “O” Ring Screw Anvil(1/2” SQ) Spring Hammer Pin Hammer Dog Trigger Hammer Cage Drive Cam Screw...
- Page 14 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...