Related Manuals for Alcatel-Lucent OmniSwitch 6450 Series
Summary of Contents for Alcatel-Lucent OmniSwitch 6450 Series
- Page 1 Part No. 060351-10, Rev. A November 2011 OmniSwitch 6450 Series Hardware Users Guide www.alcatel-lucent.com OmniSwitch 6450 Series Hardware Users Guide November 2011...
- Page 2 The specifications described in this guide are subject to change without notice. Copyright © 2011 by Alcatel-Lucent. All rights reserved. This document may not be reproduced in whole or in part without the express written permission of Alcatel-Lucent.
-
Page 3: Table Of Contents
Applications ........................1-3 Availability Features .......................1-4 Software Rollback ....................1-4 Hot Swapping ......................1-4 Hardware Monitoring ....................1-5 Chapter 2 OmniSwitch 6450 Series Chassis and Hardware Components ..... 2-1 OmniSwitch 6450-10 ......................2-3 OmniSwitch 6450-10 Front Panel ................2-4 OmniSwitch 6450-10 Rear Panel ................2-5 OmniSwitch 6450-P10 ....................2-7 OmniSwitch 6450-P10 Front Panel. - Page 4 Installing Transceivers .....................4-5 Appendix A Regulatory Compliance and Safety Information ..........A-1 Declaration of Conformity: CE Mark ................A-1 China RoHS: Hazardous Substance Table ..............A-2 Waste Electrical and Electronic Equipment (WEEE) Statement ........A-4 OmniSwitch 6450 Series Hardware Users Guide November 2011...
- Page 5 Advertencia sobre una apropiada conexión a tierra ........A-14 Leer “información importante de seguridad” ..........A-14 Advertencia de acceso restringido ..............A-14 Advertencia de pulsera antiestática ..............A-14 Clase de seguridad ..................A-14 OmniSwitch 6450 Series Hardware Users Guide November 2011...
- Page 6 Contents OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 7: About This Guide
About This Guide This OmniSwitch 6450 Series Hardware Users Guide describes your switch hardware components and basic switch hardware procedures. Supported Platforms This information in this guide applies to the following products: • OmniSwitch 6450-10(L) • OmniSwitch 6450-P10(L) Note. Only the OmniSwitch 6450-10 is available with AOS Release 6.6.2.R02. - Page 8 OmniSwitch 6600 Series • OmniSwitch 6800 Series • OmniSwitch 6850 Series • OmniSwitch 6855 Series • OmniSwitch 7700 • OmniSwitch 7800 • OmniSwitch 8800 • OmniSwitch 9000 Series • OmniStack • OmniAccess page viii OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 9: Who Should Read This Manual
CLI commands that pertain directly to hardware configuration, but it is not intended as a software users guide. There are several OmniSwitch 6450 Series users guides that focus on switch soft- ware configuration. Consult those guides for detailed information and examples for configuring your switch software to operate in a live network environment. -
Page 10: How Is The Information Organized
About This Guide How is the Information Organized? This users guide provides an overview of OmniSwitch 6450 Series switches, specifications of the hard- ware components, steps for setting up and managing OmniSwitch 6450 Series switches, and an overview and procedures for managing Power over Ethernet (PoE). - Page 11 CLI-to-MIB variable mapping information for all CLI commands supported by the switch. This guide can be consulted anytime during the configuration process to find detailed and specific information on each CLI command. OmniSwitch 6450 Series Hardware Users Guide November 2011 page xi...
-
Page 12: Related Documentation
Related Documentation About This Guide Related Documentation The following are the titles and descriptions of all the OmniSwitch 6450 Series user manuals: • OmniSwitch 6450 Series Getting Started Guide Describes the hardware and software procedures for getting an OmniSwitch up and running. Also provides information on fundamental aspects of OmniSwitch software. -
Page 13: Published / Latest Product Documentation
Published / Latest Product Documentation Published / Latest Product Documentation All user guides for the OmniSwitch Series are included on the Alcatel-Lucent public website. This website also includes user guides for other Alcatel-Lucent Enterprise products. The latest user guides can be found on our website at: http://enterprise.alcatel-lucent.com/?dept=UserGuides&page=Portal... - Page 14 Technical Support About This Guide page xiv OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 15: Omniswitch 6450 Series
1 OmniSwitch 6450 Series The Alcatel-Lucent OmniSwitch 6450 Series is a set of stackable switches designed for Enterprise and Metro applications providing Fast Ethernet connectivity with Advanced Layer 2 software and basic rout- ing. OS6450-10(L) OS6450-P10(L) OmniSwitch 6450 Series OmniSwitch 6450 Series Hardware Users Guide... -
Page 16: Chassis Configurations
Chassis Configurations OmniSwitch 6450 Series Chassis Configurations OmniSwitch 6450 Series (OS6450) switches offer various Gigabit Ethernet port solutions. The following chassis configurations are available: SMB Models • OmniSwitch 6450-10: Provides eight (8) 10/100/1000BaseT Ethernet ports, two (2) combo ports, two (2) non-combo SFP ports, and an internal AC power supply. -
Page 17: Omniswitch 6450 Feature Overview
OmniSwitch 6450 Feature Overview OmniSwitch 6450 Feature Overview Security Features OmniSwitch 6450 Series switches offer extensive security features for network access control, policy enforcement and attack containment, enabling fully secure networks and OmniVista Network Manage- ment System (NMS) support. Applications Well-suited for traditional enterprise network applications. -
Page 18: Availability Features
OmniSwitch 6450 Series Availability Features OmniSwitch 6450 Series switches incorporate advanced Alcatel-Lucent Operating System (AOS) proto- cols to ensure high availability for mission critical applications. Availability features are hardware- and software-based safeguards that help to prevent the loss of data flow in the unlikely event of a subsystem failure. -
Page 19: Hardware Monitoring
LEDs, which provide visual status information, are provided on the chassis front panel. LEDs are used to indicate conditions such as hardware and software status, temperature errors, link integrity, data flow, etc. For detailed LED descriptions, refer to Chapter 2, “OmniSwitch 6450 Series Chassis and Hardware Components.” User-Driven Monitoring User-driven hardware monitoring refers to CLI commands that are entered by the user in order to access the current status of hardware components. - Page 20 Availability Features OmniSwitch 6450 Series page 1-6 OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 21: Chapter 2 Omniswitch 6450 Series Chassis And Hardware Components
2 OmniSwitch 6450 Series Chassis and Hardware Components OmniSwitch 6450 Series switches are available in the chassis configurations as shown in the table below: OmniSwitch 6450-10 Ten port 10/100/1000BaseT model. (OS6450-10) OmniSwitch 6450-P10 Ten port 10/100/1000BaseT Power Over Ethernet model. - Page 22 This chapter includes detailed information on these chassis types. Topics include: • OmniSwitch 6450 Series chassis descriptions • Technical specifications • Power Supplies • Cables and power cords • Console port and pinout specifications page 2-2 OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 23: Omniswitch 6450-10
(8) Non-combo 10/100/1000Base-T ports • (2) Non-combo 100/1000BaseX ports • (2) Combo 10/100/1000Base-T or 100/1000BaseX ports • Internal AC Power Supply • Console port (RJ-45) • USB port (USB 2.0) • Fanless design OmniSwitch 6450 Series Hardware Users Guide November 2011 page 2-3... -
Page 24: Omniswitch 6450-10 Front Panel
When pushed all LEDs will turn off and the LED of the Stack ID will remain lit. Refer to “OmniSwitch 6450 Series - LED Status” on page 2-11 for LED status information. page 2-4 OmniSwitch 6450 Series Hardware Users Guide... -
Page 25: Omniswitch 6450-10 Rear Panel
All production versions of the chassis have these labels. OmniSwitch 6450-10 Rear Panel Item Description Power Supply Connector Internal AC power supply. Grounding Block Type LCD8-10A-L grounding lug OmniSwitch 6450 Series Hardware Users Guide November 2011 page 2-5... - Page 26 10BaseT: unshielded twisted-pair (UTP) (RJ-45) 100BaseTX: unshielded twisted-pair (UTP), Category 5, EIA/TIA 568 or shielded twisted-pair (STP), Category 5, 100 ohm 1000BaseT: unshielded twisted-pair (UTP), Category 5e Maximum cable distance 100 meters (RJ-45) page 2-6 OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 27: Omniswitch 6450-P10
(8) Non-combo 10/100/1000Base-T PoE ports • (2) Non-combo 100/1000BaseX ports • (2) Combo 10/100/1000Base-T or 100/1000BaseX ports • Internal AC Power Supply • Console port (RJ-45) • USB port (USB 2.0) • Fanless design OmniSwitch 6450 Series Hardware Users Guide November 2011 page 2-7... -
Page 28: Omniswitch 6450-P10 Front Panel
When pushed all LEDs will turn off and the LED of the Stack ID will remain lit. Refer to “OmniSwitch 6450 Series - LED Status” on page 2-11 for LED status information. page 2-8 OmniSwitch 6450 Series Hardware Users Guide... -
Page 29: Omniswitch 6450-P10 Rear Panel
All production versions of the chassis have these labels. OmniSwitch 6450-P10 Rear Panel Item Description Power Supply Connector Internal AC power supply. Grounding Block Type LCD8-10A-L grounding lug OmniSwitch 6450 Series Hardware Users Guide November 2011 page 2-9... - Page 30 10BaseT: unshielded twisted-pair (UTP) (RJ-45) 100BaseTX: unshielded twisted-pair (UTP), Category 5, EIA/TIA 568 or shielded twisted-pair (STP), Category 5, 100 ohm 1000BaseT: unshielded twisted-pair (UTP), Category 5e Maximum cable distance 100 meters (RJ-45) page 2-10 OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 31: Omniswitch 6450 Series - Led Status
OmniSwitch 6450 Series - LED Status State Description Solid Green Normal operation. Blinking Green Diagnostics in progress. Solid Amber Diagnostics failed. Blinking Amber System fan failed. Solid Green Primary unit in a stack or standalone switch. Solid Amber Secondary unit in a stack. -
Page 32: Omniswitch 6450 Series - Power Supplies
OmniSwitch 6450 Series - Power Supplies • Internal 30W AC System Power Supply (see “Internal 30W AC Power Supply” on page 2-13) • Internal 120W AC System Power Supply (see “Internal 120W AC Power Supply” on page 2-13) page 2-12... -
Page 33: Internal 30W Ac Power Supply
OmniSwitch 6450-P10 Input Voltage Range 115-230 VAC Rated Frequency 50 to 60 Hz Maximum Output Power 120 W Output Voltage 12.0 VDC / 54.5 VDC Output Current 2.5 A / 1.65A OmniSwitch 6450 Series Hardware Users Guide November 2011 page 2-13... -
Page 34: Ac Power Cords
JIS 8303 Australia AS 3112 India BS 546 IEC-60320-C15 Italy CIE 23-16 Switzerland / Liechtenstein SEV 1011 Denmark / Greenland SRAF 1962 / DB 16/87 Argentina A-10 Power Cord Specifications page 2-14 OmniSwitch 6450 Series Hardware Users Guide November 2011... -
Page 35: Console Port
Serial Connection Default Settings The factory default settings for the serial connection are as follows: baud rate 9600 parity none data bits (word size) stop bits flow control none OmniSwitch 6450 Series Hardware Users Guide November 2011 page 2-15... -
Page 36: Port Pinouts
10/100 Ethernet Port – RJ-45 Pinout (non-PoE) Pin Number Description not used not used not used not used Gigabit Ethernet Port – RJ-45 Pinout Pin Number Description BI_DB+ BI_DB- BI_DA+ BI_DD+ BI_DD- BI_DA- BI_DC+ BI_DC- page 2-16 OmniSwitch 6450 Series Hardware Users Guide November 2011... -
Page 37: 10/100/1000 Mbps Power Over Ethernet Port - Rj-45 Pinout
Verify proper airflow to the chassis. • Time of the failure Use the snmp station command and refer to the SNMP Configuration chapter for information on config- uring an SNMP station. OmniSwitch 6450 Series Hardware Users Guide November 2011 page 2-17... - Page 38 2-18 OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 39: Mounting Omniswitch 6450 Series Switches
Anti-Static Warning. Before handling any components, free yourself of static by wearing a grounding strap, or by grounding yourself properly. Static discharge can damage the switch and the backup power supply. OmniSwitch 6450 Series Hardware Users Guide November 2011 page 3-1... -
Page 40: General Installation Recommendations
General Installation Recommendations Cooling Recommendations OmniSwitch 6450 Series switches are convection-cooled. Although air flow is not mandatory for switch operation, the best way to ensure proper cooling is to provide some ambient air flow over the switch whenever possible (e.g., from room fans, etc.). -
Page 41: Recommended Clearances
Reliable Earthing Reliable earthing of rack-mount equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips). OmniSwitch 6450 Series Hardware Users Guide November 2011 page 3-3... -
Page 42: Rack-Mounting Os6450 Switches
It is recommended that two people install the switch assembly on the rack—one person to hold the chassis and position it on the rack, and a second person to secure the chassis to the rack using attachment screws. (Please note that Alcatel-Lucent does not provide rack-mount screws. Use the screws supplied by the rack vendor.) •... -
Page 43: Rack Mounting Kit Components
The following diagram shows the various components for each kit. Plate and Screws Slot -bracket Power Supply Tray Rear Bracket (Not used) OS6450-DUAL-MNT Short Bracket Long Bracket OS6450-RM-19-L Tray OS6450-TRAY-19 OmniSwitch 6450 Series Hardware Users Guide November 2011 page 3-5... -
Page 44: Os6450-Dual-Mnt - Mounting Instructions
Two chassis can be assembled side-by-side for mounting into a standard 19-inch rack as show in the figure below . Rear center brackets. Front center mounting brackets. Fully Assembled Side-by-Side Chassis Assembly page 3-6 OmniSwitch 6450 Series Hardware Users Guide November 2011... - Page 45 Attach the slot-brackets and slide-brackets to the front and back of the chassis using the attachment screws (M3 flat head) provided for each bracket. Attach Slot/Slide-Brackets Align the chassis and slide both front and rear center brackets together. Slide chassis together Slide Chassis Together OmniSwitch 6450 Series Hardware Users Guide November 2011 page 3-7...
- Page 46 Align the holes in the flanges with the rack holes and insert rack mount screws (not provided) through the bottom hole of each flange and then the top of each flange. Tighten both screws until they are secure. page 3-8 OmniSwitch 6450 Series Hardware Users Guide November 2011...
- Page 47 No minimum clearance is required below the chassis assembly. However, be sure that the bottom of the chassis is not in direct contact with any equipment below. Rack-mounting Two Chassis OmniSwitch 6450 Series Hardware Users Guide November 2011 page 3-9...
-
Page 48: Os6450-Rm-19L Kit - Mounting Instructions
No minimum clearance is required below the chassis assembly. However, be sure that the bottom of the chassis is not in direct contact with any equipment below. Rack-mounting Single Chassis page 3-10 OmniSwitch 6450 Series Hardware Users Guide November 2011... -
Page 49: Os6450-Tray-19 Kit - Mounting Instructions
Note. If you are installing two chassis side-by-side in the tray, be sure to install any required center brack- ets between the two chassis. Refer to your switch’s Hardware User Guide for additional information. OmniSwitch 6450 Series Hardware Users Guide November 2011... -
Page 50: General Table-Mounting Guidelines
Mounting OmniSwitch 6450 Series Switches Table-Mounting OS6450 Switches General Table-Mounting Guidelines OmniSwitch 6450 Series switches can be installed freestanding as tabletop-mounted units. If you will be table-mounting your switch(es), refer to the important guidelines below before installing. • When choosing a location for the switch, be sure that adequate clearance has been provided for chassis airflow and access to the front, back, and sides of the chassis. -
Page 51: Connecting Chassis To Power Source
Follow the steps below to power on the chassis using and AC power source: Connect the IEC-60320-C15 end of the supplied power cord to the chassis. Connect power supply to AC power source. Monitor the chassis as it boots. OmniSwitch 6450 Series Hardware Users Guide November 2011 page 3-13... - Page 52 Connecting Chassis to Power Source Mounting OmniSwitch 6450 Series Switches page 3-14 OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 53: Booting Omniswitch 6450 Series Switches
The switch does not use an on/off switch. The power cord is the switch’s only connect/disconnect device. The power connector socket is located on the power supply rear panel. For more information, refer to “OmniSwitch 6450 Series Chassis and Hardware Components” on page 2-1. -
Page 54: Console Port
To change the data bits (i.e., word size) value, enter boot serialwordsize, followed by the number of data bits. Options include 7 and 8 (default). For example: Boot > boot serialwordsize 7 page 4-2 OmniSwitch 6450 Series Hardware Users Guide November 2011... - Page 55 To save changes to the boot.params file, refer to step 7. Return to the CLI prompt by entering exit at the boot prompt. OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 56: Monitoring The Chassis
= 76, Temperature Status = UNDER THRESHOLD, Temperature Danger Threshold (deg C) = 83 For a complete list of output definitions for this command, refer to the OmniSwitch CLI Reference Guide. page 4-4 OmniSwitch 6450 Series Hardware Users Guide November 2011... -
Page 57: Viewing The Power Supply Status
• System Status LEDs • Combo Port Status LEDs For tables showing LED states operating normally, refer to “OmniSwitch 6450 Series - LED Status” on page 2-11. Installing Transceivers For information on installing transceivers refer to the OmniSwitch Transceivers Guide. - Page 58 Monitoring the Chassis Booting OmniSwitch 6450 Series Switches page 4-6 OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 59: Regulatory Compliance And Safety Information
73/23/EEC und des 89/336/EEC, wie von Directive 93/68/EEC geändert. Español: Este directivo equipo está en conformidad con los requisitos esenciales y otras provisiones 73/23/EEC y 89/336/EEC según la enmienda prevista por Directive 93/68/EEC. OmniSwitch 6450 Series Hardware Users Guide November 2011 page A-1... -
Page 60: China Rohs: Hazardous Substance Table
对销售之日的所售产品, 本表显示, 阿尔卡特朗讯公司供应链的电子信息产品可能包含这些物质。注意: 在所售产 品中可能会也可能不会含有所有所列的部件。 This table shows where these substances may be found in the supply chain of Alcatel-Lucent electronic information products, as of the date of sale of the enclosed product. Note that some of the component types listed above may or may not be a part of the enclosed product. - Page 61 Regulatory Compliance and Safety Information China RoHS: Hazardous Substance Table Products are packaged using one or more of the following packaging materials: Corrugated Cardboard Corrugated Fiberboard Low-Density Polyethylene OmniSwitch 6450 Series Hardware Users Guide November 2011 page A-3...
-
Page 62: Waste Electrical And Electronic Equipment (Weee) Statement
Switzerland and therefore marked with the symbol: Treatment applied at end of life of the product in these countries shall comply with the applicable national laws implementing directive 2002/96EC on waste electrical and electronic equipment (WEEE). page A-4 OmniSwitch 6450 Series Hardware Users Guide November 2011... -
Page 63: Standards Compliance
EN 61000-4-4: 1995 • EN 61000-4-5: 1995 • EN 61000-4-6: 1996 • EN 61000-4-8: 1994 • EN 61000-4-11: 1994 • IEEE 802.3: Hi-Pot Test (2250 VDC on all Ethernet ports) OmniSwitch 6450 Series Hardware Users Guide November 2011 page A-5... -
Page 64: Fcc Class A, Part 15
CISPR22 Class A warning This is a Class A product. In a domestic environment, this product may cause radio interference. Under such circumstances, the user may be requested to take appropriate countermeasures. page A-6 OmniSwitch 6450 Series Hardware Users Guide November 2011... -
Page 65: Vcci
This is a Class A Information Product. When used in a residential environment, it may cause radio frequency interference. Under such circumstances, the user may be requested to take appropriate counter- measure. OmniSwitch 6450 Series Hardware Users Guide November 2011 page A-7... -
Page 66: Translated Safety Warnings
Installationen, Wartungen oder Konfigurationen vorgenommen werden. Español: Para evitar peligro de descargas, no conecte o desconecte ningun cable, ni realice ninguna insta- lación, maintenimiento o reconfiguración de este producto durante una tormenta eléctrica. page A-8 OmniSwitch 6450 Series Hardware Users Guide November 2011... -
Page 67: Installation Warning
Any equipment to which this product will attached must also be connected to properly wired recep- tacles. • Use 22AWG solid copper conductor for ground leads connecting the frame to ground and DC return. OmniSwitch 6450 Series Hardware Users Guide November 2011 page A-9... - Page 68 • Cualquier otro equipo a cual se conecte este producto también debe estar conectado a tomas de alimentación adecuadamente cableadas. page A-10 OmniSwitch 6450 Series Hardware Users Guide November 2011...
-
Page 69: Read Important Safety Information Warning
Español: Este equipo se debe instalar en un sitio con acceso restrinjido. Un sitio con el acceso restrinjido es uno seguro y con acceso limitado al personal de servicio que tiene una clave especial u otros medios de seguridad. OmniSwitch 6450 Series Hardware Users Guide November 2011 page A-11... -
Page 70: Wrist Strap Warning
Français: L'électricité statique (ESD) peut endommager les composants du commutateur. Pour cette raison Alcatel-Lucent joint à l'envoi du châssis un bracelet antistatique à brancher sur la prise mise à la terre située en bas à droite du commutateur. Vous devrez mettre ce bracelet avant toute intervention hard- ware. -
Page 71: Instrucciones De Seguridad En Español
Deseche las baterías usadas según las instrucciones del fabricante. Las instrucciones del fabricante son como sigue: Devuelva el módulo con la batería del litio a Alcatel-Lucent. La batería del litio será substitu- ida en la fábrica de Alcatel-Lucent. -
Page 72: Advertencia Sobre Una Apropiada Conexión A Tierra
CA con descarga a tierra. Clase de seguridad Cumple con 21CFR 1040.10 y 1040.11 ó sus equivalentes. page A-14 OmniSwitch 6450 Series Hardware Users Guide November 2011...