Μcrc Register Description; Μcrc Register Summary - Texas Instruments Concerto F28M35 Series Technical Reference Manual

System Control Registers
Table 1-165. EXEONLYR Register Field Description (continued)
Bit Field
7 EXEONLY_SECT
G
6 EXEONLY_SECT
H
5 EXEONLY_SECT
I
4 EXEONLY_SECT
J
3 EXEONLY_SECT
K
2 EXEONLY_SECT
L
1 EXEONLY_SECT
M
0 EXEONLY_SECT
N
1.13.10 µCRC Register Description
The following table summarizes the registers for µCRC.
Name
µCRCCONFIG
µCRCCONTROL
268
System Control and Interrupts
Value Description
Value in this field gets loaded from EXEONLY[7:7] when a read is issued to the EXEONLY address
location in flash.
0 Execute-Only protection is enabled for C28x Flash Sector G (only if it is allocated to the control
subsystem)
1 Execute-Only protection is disabled for C28x Flash Sector G (only if it is allocated to the control
subsystem)
Value in this field gets loaded from EXEONLY[6:6] when a read is issued to the EXEONLY address
location in flash.
0 Execute-Only protection is enabled for C28x Flash Sector H (only if it is allocated to the control
subsystem)
1 Execute-Only protection is disabled for C28x Flash Sector H (only if it is allocated to the control
subsystem)
Value in this field gets loaded from EXEONLY[5:5] when a read is issued to the EXEONLY address
location in flash.
0 Execute-Only protection is enabled for C28x Flash Sector I (only if it is allocated to the control
subsystem)
1 Execute-Only protection is disabled for C28x Flash Sector I (only if it is allocated to the control
subsystem)
Value in this field gets loaded from EXEONLY[4:4] when a read is issued to the EXEONLY address
location in flash.
0 Execute-Only protection is enabled for C28x Flash Sector J (only if it is allocated to the control
subsystem)
1 Execute-Only protection is disabled for C28x Flash Sector J (only if it is allocated to the control
subsystem)
Value in this field gets loaded from EXEONLY[3:3] when a read is issued to the EXEONLY address
location in flash.
0 Execute-Only protection is enabled for C28x Flash Sector K (only if it is allocated to C28x zone1)
1 Execute-Only protection is disabled for C28x Flash Sector K (only if it is allocated to C28x zone1)
Value in this field gets loaded from EXEONLY[2:2] when a read is issued to the EXEONLY address
location in flash.
0 Execute-Only protection is enabled for C28x Flash Sector L (only if it is allocated to the control
subsystem)
1 Execute-Only protection is disabled for C28x Flash Sector L (only if it is allocated to the control
subsystem)
Value in this field gets loaded from EXEONLY[1:1] when a read is issued to the EXEONLY address
location in flash.
0 Execute-Only protection is enabled for C28x Flash Sector M (only if it is allocated to the control
subsystem)
1 Execute-Only protection is disabled for C28x Flash Sector M (only if it is allocated to the control
subsystem)
Value in this field gets loaded from EXEONLY[0:0] when a read is issued to the EXEONLY address
location in flash.
0 Execute-Only protection is enabled for C28x Flash Sector N (Dedicated for the control subsystem
only)
1 Execute-Only protection is disabled for C28x Flash Sector N (Dedicated for the control subsystem
only)
Table 1-166. µCRC Register Summary
Address (Offset)
0x0
0x4
Copyright © 2012–2019, Texas Instruments Incorporated
Size (X32)
1
1
SPRUH22I – April 2012 – Revised November 2019
www.ti.com
Description
µCRC Configuration Register
µCRC Control Register
Submit Documentation Feedback