Page 1 IBM IntelliStation M Pro Types 6220 and 6230 Hardware Maintenance Manual...
Page 3 IBM IntelliStation M Pro Types 6220 and 6230 Hardware Maintenance Manual...
Page 4 Before using this information and the product it supports, read “Notices” on page 164. Fourth Edition (December 2004) The most recent version of this document is available at http://www.ibm.com/pc/support. © Copyright International Business Machines Corporation 2004. All rights reserved. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract...
Page 5: Important Safety Information
About this manual This manual contains diagnostic information, a Symptom-to-FRU index, service ® information, error codes, error messages, and configuration information for the IBM ® IntelliStation M Pro Types 6220 and 6230. Important: The field replaceable unit (FRU) procedures are intended for trained servicers who are familiar with IBM products.
Page 6 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 7: Table Of Contents
Creating and using an IBM Enhanced Diagnostics diskette ..22 Creating an IBM Enhanced Diagnostics diskette ... . 22 Using the IBM Enhanced Diagnostics diskette ... . 22 Creating an emergency recovery-repair diskette .
Page 8 System board ......82 IntelliStation M Pro Type 6230 (tower model) ....84 Removing the front bezel .
Page 9 Problem determination tips ....116 Parts listing for IntelliStation M Pro Type 6220 and 6230 computer ..119 Type 6220 .
Page 10 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 11: General Checkout
For information about power supply problems, see “Symptom-to-FRU index” on page 99 For safety information, see “Safety information” on page 129. For intermittent problems, check the error log; see “POST error log” on page 17 and “Undetermined problems” on page 115. © Copyright IBM Corp. 2004...
Page 12 If you receive an error, see “Symptom-to-FRU index” on page 99. If the diagnostics were completed successfully and you still suspect a problem, see “Undetermined problems” on page 115. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 13: General Information
IBM IntelliStation Documentation CD This CD contains all of the IBM IntelliStation M Pro Types 6220 and 6230 publications in Portable Document Format (PDF). © Copyright IBM Corp. 2004...
Page 14: Notices And Statements Used In This Book
Danger: These statements indicate situations that can be potentially lethal or extremely hazardous to you. A danger statement is placed just before the description of a potentially lethal or extremely hazardous procedure step or situation. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 15: Features And Specifications - M Pro Type 6220 (Desktop Model)
Features and specifications — M Pro Type 6220 (desktop model) The following table provides a summary of the features and specifications of the IntelliStation M Pro Type 6220 desktop computer. Depending on the model, some features might not be available, or some specifications might not apply.
Page 16: Features And Specifications - M Pro Type 6230 (Tower Model)
Features and specifications — M Pro Type 6230 (tower model) The following table provides a summary of the features and specifications of the IntelliStation M Pro Type 6230 tower computer. Depending on the model, some features might not be available, or some specifications might not apply.
Page 17: Controls And Indicators
Controls and indicators The following illustration shows the controls and indicators on the M Pro Type 6220 desktop computer. Note: The illustrations in this document might differ slightly from your hardware. Ethernet transmit/ receive activity Ethernet link status LED CD-ROM drive activity LED CD eject button...
Page 18: Turning On The Computer
The power-on LED flashes to indicate that the computer is connected to an ac power source but is not turned on (standby mode). IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 19 Press CTRL+A for SCSISelect Utility (some models) Note: To start the Product Recovery Program in Red Hat Linux, watch the screen until the operating system selection menu displays and select IBM Preload Recovery and Diagnostics. To use these features, press the appropriate function key or keys quickly. The messages appear for only a short time.
Page 20: Turning Off The Computer
You can press and hold the power-control button for more than 4 seconds to cause an immediate shutdown of the computer. You can use this feature to turn off the computer if the operating system stops functioning. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 21: Configuration
You must press F1 quickly.) If you have set both administrator and user passwords, you must type the administrator password to access the full Configuration/Setup Utility menu. 3. Follow the instructions that appear on the screen. © Copyright IBM Corp. 2004...
Page 22: Configuration/Setup Utility Menu Choices
You can enable a virus-detecting test that checks for changes in the boot record when the computer starts. You also can select to run POST in the quick mode or read the microprocessor serial number. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 23: Using Passwords
This choice is on the full Configuration/Setup Utility menu only. v Advanced Setup Select this choice to change values for advanced hardware features, such as Cache Control and PCI configuration. Important: The computer might malfunction if these options are incorrectly configured.
Page 24: Enabling The Intel Gigabit Ethernet Utility
– SCSI Controller ID Select this choice to view the SCSI controller ID, which is typically 7. – SCSI Controller Termination This choice is set to Enabled and cannot be changed. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 25: Configuring The Gigabit Ethernet Controller
You do not need to set any jumpers or configure the controller. However, you must install a device driver to enable the operating system to address the controller. For device drivers and information about configuring your Gigabit Ethernet controller, go to http://www.ibm.com/pc/support/. Configuration...
Page 26 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 27: Diagnostics
POST generates beep codes to indicate successful completion or the detection of a problem. v One short beep indicates the successful completion of POST. v More than one beep or no beep indicates that POST detected a problem. For more information, see “Beep symptoms” on page 99. © Copyright IBM Corp. 2004...
Page 28: Small Computer System Interface (Scsi) Messages (Some Models)
Function Name: Result (test specific string) where: Result is one of the following results: Passed The test was completed without any errors. Failed The test detected an error. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 29: Downloading The Diagnostics Program
Downloading the diagnostics program Complete the following steps to download the latest image of the IBM Enhanced Diagnostics from the World Wide Web and create a startable Enhanced Diagnostics diskette: 1.
Page 30: Pc-Doctor For Windows
Product Recovery program will be lost. If your hard disk drive, including the partition where the Product Recovery program is, becomes damaged or you replace the hard disk drive, contact IBM to order the IBM Product Recovery CD to recover your preinstalled operating system, application programs, and device drivers.
Page 31: Recovering Or Installing Device Drivers
3. Turn on your computer, and wait for the operating system menu to be displayed; then, quickly select IBM Preload Recovery and Diagnostics. 4. Select the recovery options you want, and follow the instructions on the screen.
Page 32: Creating And Using An Ibm Enhanced Diagnostics Diskette
Device drivers for IBM devices and the instructions to install them (readme.txt) are on the Device Drivers and Enhanced Diagnostics CD and in the c:\ibmtools\drivers\ directory. The latest device drivers are also available at http://www.ibm.com/pc/support/. Creating and using an IBM Enhanced Diagnostics diskette The IBM Enhanced Diagnostics diskette is used to test hardware components on your computer.
Page 33: Creating An Emergency Recovery-Repair Diskette
Creating an emergency recovery-repair diskette At your earliest opportunity, create a recovery-repair diskette and an IBM Enhanced Diagnostics diskette, and store them in a safe place. In the unlikely event that your computer becomes unusable, you can use the recovery-repair diskette to access the Product Recovery program.
Page 34: Using The Recovery-Repair Diskette
Product Recovery program. Use a Product Recovery CD to access the Product Recovery program. To obtain a Product Recovery CD, contact IBM. See “Recovery CD, Type 6220 and 6230” on page 125 for details.
Page 35: Updating Bios Code
12. Select Save Settings and press Enter. Updating BIOS code You can download the latest BIOS code from http://www.ibm.com/pc/support/. Use this code to create a POST/BIOS flash diskette. Complete the following steps to update the BIOS code on the computer: 1.
Page 36: Recovering From A Post/Bios Update Failure
12. Remove the diskette from the diskette drive. 13. Disconnect all power cords; then, remove the computer cover. 14. Return the boot block recovery jumper to pins 1 and 2. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 37: Clearing Cmos Memory
1 Gbps Ethernet controller. Information is also available on the Ethernet controller documentation on the Device Drivers and IBM Enhanced Diagnostics CD for information about problems that might occur with the 1 Gbps Ethernet controller. The way the Ethernet controller is tested depends on which operating system you are using (see the Ethernet controller device-driver file).
Page 38: Network Connection Problems
If the hub does not support auto-negotiation, manually configure the Ethernet controller to match the hub. v If you manually configured the duplex mode, make sure that you also manually configure the speed. v Reseat or replace the adapter. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 39: Replacing The Battery
Statement 2: CAUTION: When replacing the lithium battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer.
Page 40 6. Turn on the computer. 7. Start the Configuration/Setup Utility program and set configuration parameters. v Set the system date and time. v Set passwords if necessary. v Save the configuration. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 41: Installing Options
This chapter provides instructions for installing or replacing options in your computer. For a list of supported options for your computer, go to http://www.ibm.com/pc/; then, select your country and navigate to the list of options for your computer. Installation guidelines Before you begin installing options in your computer, read the following information: v Review the safety information beginning on page 129 and “Handling...
Page 42: Installing Options In The M Pro Type 6220 (Desktop Model)
The following illustration shows the major components of your M Pro Type 6220 desktop computer. Cover Adapter- retaining Memory modules bracket Frame-support bracket Hard disk drive tray Hard disk drive Drive cages CD-ROM drive IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 43: System-Board Option Connectors
System-board option connectors The following illustration shows the system-board connectors for user-installable options. Microprocessor DIMM 2 DIMM 4 and fan (U6) DIMM 1 DIMM 3 PCI 1 Battery PCI 2 Mini - PCI PCI 3 System-board internal connectors The following illustration shows the internal connectors on the system board. Microprocessor fan Main power connector...
Page 44: Removing The Cover
10); then, disconnect all power cords and external cables. 3. Press the buttons on both sides of the computer, and lift the cover from the computer. To replace the cover, see “Replacing the cover” on page 47. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 45: Removing And Installing The Support Bracket
Removing and installing the support bracket When working with some options, such as hard disk drives and memory modules, you must first remove the support bracket to access the option. Complete the following steps to remove the support bracket: 1. Review the “Installation guidelines” on page 31. 2.
Page 46 9. Follow the instructions that come with the adapter to set any jumpers or switches on the adapter or system board. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 47: Installing Internal Drives
10. Remove the adapter from the static-protective package, carefully grasp the adapter by the top edge or upper corners, and align it with the expansion slot guides. Then, press the adapter firmly into the expansion slot. Move the adapter directly from the static-protective package to the adapter slot. Avoid touching the components and gold-edge connectors on the adapter.
Page 48 3. Disconnect all power cords; then, disconnect all external cables. 4. Remove the cover and frame-support bracket. See “Removing the cover” on page 34 and “Removing and installing the support bracket” on page 35 for details. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 49 5. Rotate the drive bay cage until the latch catches the front of the computer chassis. 6. Touch the static-protective package containing the drive to any unpainted metal surface on the computer; then, remove the drive from the package and place it on a static-protective surface.
Page 50 6. Rotate the hard disk drive cage, and remove it from the computer. 7. Remove the screws holding the drive in place. 8. Slide the drive out of the drive bay from the front of the drive bay. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 51 Note: If you are installing a drive that contains a laser, observe the following safety precaution. Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation.
Page 52 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 53 8. Touch the static-protective package containing the new drive to any unpainted metal surface on the computer; then, remove the drive from the package and place it on a static-protective surface. 9. Set any jumpers or switches on the new drive according to the documentation that comes with the drive.
Page 54: Installing Memory Modules
Installing memory modules The following notes describe the types of dual inline memory modules (DIMMs) that your computer supports and other information that you must consider when installing DIMMs. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 55 1. When you restart the computer after adding or removing a DIMM, the computer displays a message that the memory configuration has changed. 2. Your IntelliStation M Pro Type 6220 computer uses industry-standard, PC2700 or PC3200 double-data-rate (DDR) dual inline memory modules (DIMMs).
Page 56: Installing A Security Rope Clip
To help prevent hardware theft, you can add a security rope clip and cable to your computer. After you add the security cable, make sure that it does not interfere with other cables that are connected to the computer. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 57: Replacing The Cover
Before you begin, obtain the following items: v A flat-blade screwdriver v An adjustable wrench v A 19 mm (0.75 in.) rope clip or wire rope (similar to National Manufacturing No. 3230, Stock No. 176-735) v Threaded nuts that fit the rope clip v A security cable v A lock, such as a combination lock or padlock Complete the following steps to install a rope clip:...
Page 58 2. Install the cover by placing it over the chassis and pivoting it down over the computer until it snaps into place. 3. Reconnect the external cables and power cords. Turn on the attached devices, and turn on the computer. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 59: Installing Options In The M Pro Type 6230 (Tower Model)
Installing options in the M Pro Type 6230 (tower model) This section provides instructions for installing hardware options in the IntelliStation M Pro Type 6230 computer. Major components of your computer The following illustration shows the major components in the M Pro Type 6230 tower computer.
Page 60: System-Board Option Connectors
The following illustration shows the system-board connectors for user-installable options. Microprocessor DIMM 2 DIMM 4 and fan (U6) DIMM 1 DIMM 3 PCI 1 Battery PCI 2 Mini - PCI PCI 3 PCI 4 PCI 5 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 61 System-board internal connectors The following illustration shows the internal connectors on the system board. Microprocessor fan Main power connector Diskette drive Front panel Power Front USB Microprocessor power Primary IDE (PRI IDE) CDROM Secondary IDE (SEC IDE) Internal speaker connector Intrusion switch Rear fan Boot block...
Page 62: Removing The Side Cover
1. Review the safety information beginning on page 129. 2. Turn off the computer and all attached devices (see “Turning off the computer” on page 10). 3. Disconnect all external cables and power cords. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 63: Removing And Installing The Support Bracket
4. Pull the cover-release latch away from the computer, and push the cover toward the rear of the computer. Lift the side cover off the computer, and set it aside. For instructions for replacing the side cover, see “Replacing the side cover” on page Attention: For proper cooling and airflow, replace the cover before turning on the computer.
Page 64: Working With Adapters
IEEE 1394 adapter installed, do not install any adapter in the mini-PCI slot. v For a list of supported options for your computer, go to http://www.ibm.com/pc/ on the World Wide Web; then, select your country, and navigate to the list of options for your computer.
Page 65 Installing an adapter Note: The AGP Pro slot and PCI slots 1, 2, and 3 must be empty for you to access the IEEE 1394 adapter in the mini-PCI slot. If you are replacing the IEEE 1394 adapter, the optional PCI adapter and the AGP video adapter will need to be temporarily removed.
Page 66 13. If you have other options to install, do so now; otherwise, continue with step IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 67 14. Replace the support bracket (see “Removing and installing the support bracket” on page 53). 15. Replace the side cover (see “Replacing the side cover” on page 67). 16. Reconnect the external cables and power cords; then, turn on the attached devices and the computer.
Page 68: Installing Internal Drives
CD-ROM, CD-RW, or DVD/CD-RW combination drive Internal drive bays Your IntelliStation M Pro computer comes with an IDE CD-ROM or DVD/CD-RW drive in bay 1, a 3.5-in., 1.44 MB diskette drive in bay 3, and a hard disk drive in bay 6 or 7.
Page 69 Preinstallation steps Some of these steps are required only the first time you install a hard disk drive in a specific bay. 1. Review the safety information beginning on page 129, “Installation guidelines” on page 31, and the documentation that comes with your drive. 2.
Page 70 Note the following. Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. EMC shield Filler panel IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 71 6. Touch the static-protective package containing the drive to any unpainted metal surface on the computer; then, remove the drive from the package and place it on a static-protective surface. 7. Follow the instructions that come with the drive to set any jumpers or switches on the drive, if any.
Page 72 17. Replace the side cover (see “Replacing the side cover” on page 67). 18. Reconnect the external cables and power cords; then, turn on the attached devices and the computer. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 73 Power and signal cables for internal drives Your computer uses cables to connect parallel IDE, serial ATA, and SCSI devices to the power supply and to the system board. (See “System-board internal connectors” on page 51 for the location of system-board connectors.) Review the following information before connecting power and signal cables to internal drives: v The drives that are preinstalled in your computer come with power and signal cables attached.
Page 74: Installing Memory Modules
1. When you restart the computer after adding or removing a DIMM, the computer displays a message that the memory configuration has changed. 2. Your IntelliStation M Pro Type 6230 computer uses industry-standard, PC2700 or PC3200 double-data-rate (DDR) dual inline memory modules (DIMMs).
Page 75 Complete the following steps to install a DIMM: 1. Review the safety information beginning on page 129, “Installation guidelines” on page 31, and “Handling static-sensitive devices” on page 31. 2. Remove the side cover (see “Removing the side cover” on page 52). 3.
Page 76: Installing A Security Rope Clip
A 19 mm (0.75 in.) rope clip or wire rope (similar to National Manufacturing No. 3230, Stock No. 176-735) v Threaded nuts that fit the rope clip v A security cable v A lock, such as a combination lock or padlock IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 77: Replacing The Side Cover
Complete the following steps to install a rope clip: 1. Turn off the computer and all attached devices. 2. Disconnect all external cables and power cords; then, remove the side cover. See “Removing the side cover” on page 52. 3. Use a screwdriver to remove the two metal knockouts. 4.
Page 78: Connecting External Options
3. Follow the instructions that come with the option to prepare it for installation and to connect it to the computer. If you are attaching a SCSI device, see “Ultra320 SCSI connector” on page 72 for SCSI ID and cabling information. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 79: Input/Output Connectors
Input/output connectors Connect optional external devices to the connectors on the front and rear of the computer. Your computer has the following input/output (I/O) connectors: v One audio line in v Two audio line out v Two audio microphone v One Ethernet v Two IEEE 1394 (some models) v One keyboard v One mouse...
Page 80: Audio Connectors
Connect a microphone to this connector to record sounds onto the hard disk or to use speech-recognition software. There are two microphone connectors, one on the front and one on the rear of the computer. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 81: Auxiliary-Device (Pointing-Device) Connector
Auxiliary-device (pointing-device) connector There is one auxiliary-device connector on the rear of the computer. Use this connector to connect a mouse or other pointing device. The following illustration shows an auxiliary-device connector. Ethernet (RJ-45) connector There is one Ethernet connector on the rear of the computer. Use this connector to connect the computer to a 10-Mbps, 100-Mbps, or 1000-Mbps network.
Page 82: Keyboard Connector
ECP and EPP modes. When the parallel connector is configured as bidirectional, use an IEEE 1284-compliant cable that does not exceed 3 meters (9.8 ft). Use the Devices and I/O Ports options in the IBM Configuration/Setup Utility program to configure the parallel connector as bidirectional.
Page 83: Universal Serial Bus (Usb) Connectors
marketing representative. To receive an indication of SCSI hard-disk drive activity, you must also connect the SCSI adapter to the SCSI LED connector on the system board. See “System-board internal connectors” on page 51 for the location of the SCSI connectors. Setting SCSI IDs Each SCSI device connected to a SCSI controller must have a unique SCSI ID.
Page 84 (LFH-60) to dual-analog monitor pigtail cable. If you want to set up two digital monitors, you will need to purchase a separate dual-digital monitor cable. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 85: Fru Information (Service Only)
FRU information (service only) The field replaceable unit (FRU) procedures are intended for trained servicers who are familiar with IBM products. See “Parts listing for IntelliStation M Pro Type 6220 and 6230 computer” on page 119 for information about CRUs and FRUs.
Page 86 5. Remove all cables that impede access to the IEEE 1394 adapter. 6. Pull the retaining latches apart, and lift the IEEE 1394 adapter out of the mini-PCI connector. To replace the IEEE 1394 adapter, reverse the steps. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 87: Adapter Retainer
Adapter retainer Before you begin: v Read “Safety information” on page 129. v Read “Installation guidelines” on page 31. v Review the information in “System reliability considerations” on page 31. Complete the following steps to remove the adapter retainer: 1. Turn off the computer and attached devices; then, disconnect all external cables and power cords.
Page 88: Operator Information Panel
To install the operator information panel, reverse the previous steps. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 89: Speaker
Speaker Before you begin: v Read “Safety information” on page 129. v Read “Installation guidelines” on page 31. v Review the information in “System reliability considerations” on page 31. Complete the following steps to remove the speaker: 1. Turn off the computer and attached devices; then, disconnect all external cables and power cords.
Page 90: Microprocessor/Fan-Sink Assembly
Note: The fan and underlying heat sink are attached and do not need to be separated from each other. Remove the fan-sink assembly from the microprocessor as a single unit. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 91 6. Remove the fan-sink assembly from the microprocessor: a. Detach the fan-sink cable. b. Loosen the two captive screws (in leaf-spring enclosures) on either side of the fan-sink assembly, exerting pressure on the screwdriver. c. With the two captive screws loosened, pivot the leaf-spring assemblies outward and out of the notches on the fan-sink assembly.
Page 92: System Board
3. Remove the air baffle (see “Baffle” on page 75). 4. Disconnect all cables on the system board. 5. Pivot the drive cages up; then, remove the drives and cages from the computer. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 93 6. Remove any of the following components that are installed on the system board: v Battery (see “Replacing the battery” on page 29). v Microprocessor (see “Microprocessor/fan-sink assembly” on page 80). Important: If you plan to reinstall an existing microprocessor to the new system board, be careful when handling the adhesive material on the microprocessor.
Page 94: Intellistation M Pro Type 6230 (Tower Model)
3. Remove the side cover (see “Removing the side cover” on page 52). 4. Press the bezel-release latch at the top of the computer to disconnect the top of the bezel from the computer. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 95: Power Button
5. Release the two tabs at the top edge of the bezel, and pull the top of the bezel slightly away from the computer. 6. Pull the bezel up to release the two tabs at the bottom edge of the bezel. Store the bezel in a safe place.
Page 96: Ieee 1394 Adapter - Type 6230
2. Remove the cover and support bracket (see “Removing the side cover” on page 52 and “Removing and installing the support bracket” on page 53). 3. Disconnect any cables that impede access to the mini-PCI IEEE 1394 adapter. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 97 4. Pull the retaining latches on the mini-PCI connector apart, and remove the IEE 1394 adapter. To replace the mini-PCI IEEE 1394 adapter, reverse the steps. FRU information (service only)
Page 98: Microprocessor/Fan-Sink Assembly
If replacement adhesive material is provided with the replacement part, be sure to remove all traces of existing adhesive material from the processor before applying the new adhesive material. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 99: Power Supply
5. Free the processor from the system board by rotating the processor socket lever arm upward to its maximum vertical position. 6. Lift the processor up and out of the computer. To install a processor, reverse the previous steps. Note: When reconnecting the fan-sink cable to the system board, be sure to connect the cable to the connector marked “CPU fan”.
Page 100: System Board And Extender Card
1. Turn off the computer and all attached devices; then, disconnect all external cables and power cords. See “Turning off the computer” on page 10. 2. Remove the side cover. See “Removing the side cover” on page 52. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 101 3. Remove the front bezel. See “Removing the front bezel” on page 84. 4. Remove the support bracket. See “Removing the side cover” on page 52. 5. Disconnect the cables. 6. Remove the adapters and both adapter retaining brackets (see “Installing an adapter”...
Page 102: Cd-Rom Drive
See “Turning off the computer” on page 10. 2. Remove the side cover. See “Removing the side cover” on page 52. 3. Disconnect the cables. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 103: Diskette Drive
4. Press the drive retaining tab, gently slide the CD-ROM drive toward the front of the computer, and lift it out. Diskette drive Before you begin: v Read “Safety information” on page 129. v Read “Installation guidelines” on page 31. v Review the information in “System reliability considerations”...
Page 104: Bezel-Release Latch
3. Remove the front bezel. See “Removing the front bezel” on page 84. 4. Remove the handle assembly. See “Handle assembly” on page 97. 5. Remove the top/side cover. See “Top/side cover” on page 95. 6. Press down on the tab. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 105: Top/Side Cover
7. From the underside, grasp the bezel-release latch in the center, and gently pull it back and away from the computer. Top/side cover Before you begin: v Read “Safety information” on page 129. v Read “Installation guidelines” on page 31. v Review the information in “System reliability considerations”...
Page 106 6. Using a screwdriver, gently pry the cover away from the computer in the rear, and slide the unit away from the computer. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 107: Handle Assembly
Handle assembly Before you begin: v Read “Safety information” on page 129. v Read “Installation guidelines” on page 31. v Review the information in “System reliability considerations” on page 31. To remove the handle cap, complete the following steps: 1. Turn off the computer and all attached devices; then, disconnect all external cables and power cords.
Page 108: Adapter Retainer
4. Remove all adapters. See “Installing an adapter” on page 55. 5. Rotate the adapter retainer to the open position. 6. Grasp the adapter retainer, and gently slide the top and bottom tabs out of the notches. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 109: Symptom-To-Fru Index
1. Check the configuration before you replace a FRU. Configuration problems can cause false errors and symptoms. 2. For IBM devices not supported by this index, see the manual for that device. 3. Always start with “General checkout” on page 1.
Page 110 1. Install or reseat the memory modules, and then do a 3-boot reset. (No operational memory in system.) (For more information about a 3-boot reset, see “Using the Configuration/Setup Utility program” on page 11). 2. DIMMs. 3. System board. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 111: No-Beep Symptoms
No-beep symptoms No-beep symptom FRU/action No beep occurs during POST. System board No beep, no video, and the System board system attention LED (if present) is off. No beep, no video, and the See “Undetermined problems” on page 115. system attention LED (if supported) is on.
Page 112 2. Verify BIOS code is at latest level. 3. Microprocessor 2. 4. System board. 206-XXX-000 1. Try test with another diskette. (Failed diskette drive test.) 2. Cable. 3. Diskette drive. 4. System board. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 113: Error Symptoms
Error code/symptom FRU/action 215-XXX-000 1. Try test with another CD-ROM. (Failed IDE CD-ROM drive test.) 2. CD-ROM drive cables. 3. CD-ROM drive. 4. System board. 217-198-XXX 1. Check cable and termination. (Could not establish drive parameters.) 2. SCSI backplane. 3. Hard disk. 217-XXX-000 1.
Page 114 4. Cable. 5. Diskette drive. 6. System board. General problems Symptom FRU/action A cover lock is broken, an LED Broken CRU/FRU is not working, or a similar problem has occurred IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 115 Hard disk drive problems Symptom FRU/action Not all drives are recognized by 1. Remove the first drive not recognized and try the hard disk drive the hard disk drive diagnostic diagnostic test again. test (the Fixed Disk test). 2. If the remaining drives are recognized, replace the drive that you removed with a new one.
Page 116 (memory connector or bank of connectors enabled). 2. If the problem remains, replace: a. Monitor b. Video adapter, if installed c. System board Only the cursor appears. See “Undetermined problems” on page 115. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 117 Non-IBM monitor cables might cause unpredictable problems. c. An enhanced monitor cable with additional shielding is available for the 9521 and 9527 monitors. For information about the enhanced monitor cable, contact your IBM marketing representative or authorized reseller. 2. Monitor. 3. Video adapter, if installed.
Page 118 If computer fails during POST and the power-control button does not work, disconnect the ac power cord. 2. If the problem remains or if you are using an ACPI-aware operating system, replace the system board. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 119: Post Error Codes
Serial port problems Symptom FRU/action The number of serial ports 1. Make sure that: identified by the operating v Each port is assigned a unique address in the Configuration/Setup Utility system is less than the number program and none of the serial ports is disabled. of serial ports that are installed.
Page 120 2. Diskette drive 3. Drive cable 4. System board 1. Run the Configuration/Setup Utility program and diagnostics. (Diskette drive error) 2. Diskette drive. 3. Drive cable. 4. System board. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 121 Error code/symptom FRU/action 1. Run the Configuration/Setup Utility program and diagnostics. (Diskette drive configuration error) 2. Diskette drive. 3. Drive cable. 4. System board. 1. Run the Configuration/Setup Utility program. (Parallel port error) 2. System board. 1162 1. Run the Configuration/Setup Utility program. (System board serial port 1 or 2 error) 2.
Page 122: Scsi Error Codes
M Pro Type 6230 (tower model)” on page 6. System over temperature for CPU x v Ensure system is being properly cooled; see “System reliability (level-warning; CPU x reporting over considerations” on page 31. temperature condition) IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 123: Fan Error Messages
Message Action System under recommended CPU x Ambient temperature must be within normal operating temperature (level-warning; system specifications; see “Features and specifications — M Pro Type 6220 reporting under temperature condition for (desktop model)” on page 5. CPU x) Fan error messages Message Action Fan x failure (level-critical;...
Page 124: System Shutdown
“Features and specifications — M Pro Type 6220 (level-critical; system board is under (desktop model)” on page 5. or “Features and specifications — M Pro temperature) Type 6230 (tower model)” on page 6. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 125: Hard Disk Drive Checkout
Hard disk drive checkout Message Action Hard drive x removal detected Information only; take action as appropriate. (level-critical; hard drive x has been removed) Host built-in self test (BIST) Message Action Host fail 1. Reseat the microprocessor. (level-informational; built-in self-test for the 2.
Page 126: Problem Determination Tips
Note: To eliminate confusion, computers are considered to be identical only if they: v Are exactly the same machine type and models v Have the same BIOS code level IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 127 v Have the same adapters and attachments in the same locations v Have the same address jumpers/terminators and cabling v Have the same software versions and levels v Have the same diagnostics code (version) v Have the same configuration options set v Have the same setup for the operating-system control files Comparing the configuration and software setup between working and nonworking computers will often lead to problem resolution.
Page 128 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 129: Parts Listing For Intellistation M Pro Type 6220 And 6230 Computer
Parts listing for IntelliStation M Pro Type 6220 and 6230 computer This parts listing supports the IntelliStation M Pro (Type 6220 and Type 6230). Field replaceable units (FRUs) should be serviced only by qualified field service technicians. Customer replacement units can be replaced by the customer.
Page 130 System (IntelliStation M Pro, Type 6220, Models 20X, B0X, 24X, B4X, Index 40X, 50X, 54X, D0X, 44X, D4X, E0X, E4X, 71x, 74x, G4x) FRU No. CRU/FRU Cover, top assembly, black (all models) 88P5925 Fan-sink assembly, P4 (all models) 01R3330 Fan-sink assembly, P4 (40x, 44x, D0x, D4x) 23K4714 Microprocessor, 800/2.8 GHz (models 20x, 24x, B0x, D4x)
Page 131 System (IntelliStation M Pro, Type 6220, Models 20X, B0X, 24X, B4X, Index 40X, 50X, 54X, D0X, 44X, D4X, E0X, E4X, 71x, 74x, G4x) FRU No. CRU/FRU Cable, SATA 1-drop (models 20x, 40x, BoG, D0G, 50x, E0x) 88P8176 Cable, SCSI 1-drop...
Page 132: Type 6230
Type 6230 This parts listing supports the IntelliStation M Pro Type 6230. System, IntelliStation M Pro, Type 6230, Models 13Z, 20X, B0X, 25X, B5X, 27X, B7X, 33X, 34X, C4X, 35Z, 36X, C6X, 38X, C8X, 39X, 41X, 51x, 52x, 55x, 56X, 58X, 59X, D1X, 46X, D6X, 49X, D9X, E1X, E2X, E6X, E8X, E9X, Index FRU No.
Page 133 System, IntelliStation M Pro, Type 6230, Models 13Z, 20X, B0X, 25X, B5X, 27X, B7X, 33X, 34X, C4X, 35Z, 36X, C6X, 38X, C8X, 39X, 41X, 51x, 52x, 55x, 56X, 58X, 59X, D1X, 46X, D6X, 49X, D9X, E1X, E2X, E6X, E8X, E9X, Index FRU No.
Page 134 System, IntelliStation M Pro, Type 6230, Models 13Z, 20X, B0X, 25X, B5X, 27X, B7X, 33X, 34X, C4X, 35Z, 36X, C6X, 38X, C8X, 39X, 41X, 51x, 52x, 55x, 56X, 58X, 59X, D1X, 46X, D6X, 49X, D9X, E1X, E2X, E6X, E8X, E9X, Index FRU No.
Page 135: Recovery Cd, Type 6220 And 6230
Recovery CD (IntelliStation M Pro, Type 6220, Models 20X, B0X, 24X, B4X, 40X, D0X, 44X, D4X and IntelliStation M Pro, Type 6230, Models 20X 22X 30X 32X 35X 40X 42X 45X 50X 52X 54X 55X 60X 63X 64X 65X 2PU 3PU 4PU 5PU 6PU B0X B2X C0X C2X C5X D0X D2X D5X E0X E2X E4X E5X F0X F3X F4X F5X) FRU No.
Page 136: Power Cords
Yugosl/Lat 89P8339 Power cords For your safety, IBM provides a power cord with a grounded attachment plug to use with this IBM product. To avoid electrical shock, always use the power cord and plug with a properly grounded outlet. IBM power cords used in the United States and Canada are listed by Underwriter’s Laboratories (UL) and certified by the Canadian Standards Association (CSA).
Page 137 Salvador, Guatemala, Guyana, Haiti, Honduras, Jamaica, Japan, Korea (South), Liberia, Mexico, Netherlands Antilles, Nicaragua, Panama, Peru, Philippines, Saudi Arabia, Suriname, Taiwan, Trinidad (West Indies), United States of America, Venezuela Parts listing for IntelliStation M Pro Type 6220 and 6230 computer...
Page 138 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 139: Related Service Information
After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective. v Reinstall all covers correctly before returning the computer to the customer. © Copyright IBM Corp. 2004...
Page 140: Electrical Safety
Regularly inspect and maintain your electrical hand tools for safe operational condition. v Do not use worn or broken tools and testers. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 141: Safety Inspection Guide
This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of non-IBM features or options that are not covered by this inspection guide.
Page 142: Handling Electrostatic Discharge-Sensitive Devices
Insulation must not be frayed or worn. 4. Remove the cover. 5. Check for any obvious non-IBM alterations. Use good judgment as to the safety of any non-IBM alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
Page 143: Grounding Requirements
Japanese v Korean v Spanish Important: Each caution and danger statement in this IBM documentation begins with a number. This number is used to cross reference an English-language caution or danger statement with translated versions of the caution or danger statement in this section.
Page 144 2. First, remove power cords from outlet. 3. Attach signal cables to connectors. 3. Remove signal cables from connectors. 4. Attach power cords to outlet. 4. Remove all cables from devices. 5. Turn device ON. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 145 Statement 2: CAUTION: When replacing the lithium battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer.
Page 146 The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 147 >50 kg (110 lb) Importante: Todas as instruções de cuidado e perigo da IBM documentation começam com um número. Este número é utilizado para fazer referência cruzada de uma instrução de cuidado ou perigo no idioma inglês com as versões traduzidas das instruções de cuidado ou perigo encontradas nesta seção.
Page 148 3. Conecte os cabos de sinal aos 3. Remova os cabos de sinal dos conectores. conectores. 4. Conecte os cabos de alimentação às 4. Remova todos os cabos dos dispositivos. tomadas. 5. LIGUE os dispositivos. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 149 Instrução 2 CUIDADO: Ao substituir a bateria de lítio, utilize apenas uma bateria IBM, Número de Peça 33F8354 ou uma bateria de tipo equivalente, recomendada pelo fabricante. Se o seu sistema possui um móídulo com uma bateria de lítio, substitua-o apenas pelo mesmo tipo de mídulo, do mesmo fabricante.
Page 150 Para remover toda a corrente elétrica do dispositivo, assegure que todos os cabos de alimentação estejam desconectados da fonte de energia elétrica. CUIDADO: IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 151 Níveis perigosos de voltagem, corrente e energia estão presentes em qualquer componente que tenha esta etiqueta afixada. Nenhuma peça localizada no interior desses componentes pode ser consertada. Se você supeitar de algum problema em alguma dessas peças, entre em contato com um técnico IBM. Instrução 23 CUIDADO: Não coloque nenhum objeto com peso superior a 50 kg (110 lbs.) sobre dispositivos...
Page 152 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 153 Related service information...
Page 154 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 155 Related service information...
Page 156 également précédées du chiffre 1 dans la présente section. Prenez connaissance de toutes les consignes de type Attention et Danger avant dm procéder aux opérations décrites par les instructions. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 157 Notice n° 1 DANGER Le courant électrique passant dans les câbles de communication, ou les cordons téléphoniques et d’alimentation peut être dangereux. Pour éviter tout risque de choc électrique: v Ne manipulez aucun câble et n’effectuez aucune opération d’installation, d’entretien ou de reconfiguration de cm produit au cours d’un orage. v Branchez tous les cordons d’alimentation sur un socle de prise de courant correctement câblé...
Page 158 ATTENTION: Remplacez la pile au lithium usagée par une pile de référence identique exclusivement - voir la référence IBM - ou par une pile équivalente recommandée par le fabricant. Si votre système est doté d’un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le même fabricant.
Page 159 Notice n° 4 ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ATTENTION: Faites-vous aider pour soulever cm produit. Notice n° 5 ATTENTION: Le bouton de mise sous tension/hors tension de l’unité et l’interrupteur d’alimentation du bloc d’alimentation ne coupent pas l’arrivée de courant électrique à...
Page 160 Wenn z. B. ein Sicherheitshinweis mit der Nummer 1 beginnt, so erscheint die übersetzung für diesen Sicherheitshinweis in diesem Abschnitt unter dem Hinweis Lesen Sie alle Sicherheitshinweise, bevor Sie eine Anweisung ausführen. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 161 Hinweis 1 VORSICHT Elektrische Spannungen von Netz-, Telefon- und Datenübertragungsleitungen sind gefährlich. Aus Sicherheitsgründen: v Bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner keine Installations-, Wartungs- oder Rekonfigurationsarbeiten durchführen. v Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzkontakt anschließen.
Page 162 Manche CD-ROM-Laufwerke enthalten eine eingebaute Laserdiode der Klasse 3A oder 3B. Die nachfolgend aufgeführten Punkte beachten. Laserstrahlung bei geöffneter Tür. Niemals direkt in den Laserstrahl sehen, nicht direkt mit optischen Instrumenten betrachten und den Strahlungsbereich meiden. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 163 Hinweis 4 ≥18 kg ≥32 kg ≥55 kg ACHTUNG: Beim Anheben der Maschine die vorgeschriebenen Sicherheitsbestimmungen beachten. Hinweis 5 ACHTUNG: Mit dem Betriebsspannungsschalter an der Vorderseite des Servers und dem Betriebsspannungsschalter am Netzteil wird die Stromversorgung für den Server nicht unterbrochen. Der Server könnte auch mehr als ein Netzkabel aufweisen. Um die gesamte Stromversorgung des Servers auszuschalten, muß...
Page 164 Keine Gegenstände, die mehr als 50 kg wiegen, auf Rack-Einheiten ablegen. >50 kg Importante: Tutti gli avvisi di attenzione e di pericolo riportati nella pubblicazione IBM documentation iniziano con un numero. Questo numero viene utilizzato per confrontare avvisi di attenzione o di pericolo in inglese con le versioni tradotte riportate in questa sezione.
Page 165 Avviso 1 PERICOLO La corrente elettrica circolante nei cavi di alimentazione, del telefono e di segnale è pericolosa. Per evitare il pericolo di scosse elettriche: v Non collegare o scollegare i cavi, non effettuare l’installazione, la manutenzione o la riconfigurazione di questo prodotto durante i temporali. v Collegare tutti i cavi di alimentazione ad una presa elettrica correttamente cablata e munita di terra di sicurezza.
Page 166 Avviso 2 ATTENZIONE: Quando si sostituisce la batteria al litio, utilizzare solo una batteria IBM con numero parte 33F8354 o batterie dello stesso tipo o di tipo equivalente consigliate dal produttore. Se il sistema di cui si dispone è provvisto di un modulo contenente una batteria al litio, sostituire tale batteria solo con un tipo di modulo uguale a quello fornito dal produttore.
Page 167 Avviso 4 ≥18 kg ≥32 kg ≥55 kg ATTENZIONE: Durante il sollevamento della macchina seguire delle norme di sicurezza. Avviso 5 ATTENZIONE: Il pulsante del controllo dell’alimentazione situato sull’unità e l’interruttore di alimentazione posto sull’alimentatore non disattiva la corrente elettrica fornita all’unità.
Page 168 Avviso 23 ATTENZIONE: Non poggiare oggetti che pesano più di 50 kg sulla parte superiore delle unità montate in rack. >50 kg IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 169 Related service information...
Page 170 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 171 > 50 Kg Related service information...
Page 173 Related service information...
Page 174: Notices
Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any IBM intellectual property right may be used instead.
Page 175: Edition Notice
Web sites. The materials at those Web sites are not part of the materials for this IBM product, and use of those Web sites is at your own risk. IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.
Page 176: Important Notes
IBM makes no representations or warranties with respect to non-IBM products. Support (if any) for the non-IBM products is provided by the third party, not IBM. IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 177: Product Recycling And Disposal
Before this unit is disposed of, these materials must be removed and recycled or discarded according to applicable regulations. IBM offers product-return programs in several countries. Information on product recycling offerings can be found on IBM’s Internet site at http://www.ibm.com/ibm/environment/products/prp.shtml. Battery return program This product may contain a sealed lead acid, nickel cadmium, nickel metal hydride, lithium, or lithium ion battery.
Page 178 This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Taiwanese Class A warning statement IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 179: Power Cords
Japanese Voluntary Control Council for Interference (VCCI) statement Power cords For your safety, IBM provides a power cord with a grounded attachment plug to use with this IBM product. To avoid electrical shock, always use the power cord and plug with a properly grounded outlet.
Page 180 Netherlands Antilles, Nicaragua, Panama, Peru, Philippines, Taiwan, United States of America, Venezuela 24P6858 Korea (Democratic People’s Republic of), Korea (Republic of) 34G0232 Japan 36L8880 Argentina, Paraguay, Uruguay 49P2078 India 49P2110 Brazil IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 181 IBM power cord part number Used in these countries and regions 6952300 Antigua and Barbuda, Aruba, Bahamas, Barbados, Belize, Bermuda, Bolivia, Caicos Islands, Canada, Cayman Islands, Colombia, Costa Rica, Cuba, Dominican Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Jamaica, Mexico,...
Page 182 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 183: Index
(USB) 8, 73 cabling video 73 Ethernet 71 connectors serial ATA drives 44 adapter 33, 50 small computer system interface (SCSI) adapter 57 battery 33, 50 small computer system interface (SCSI) cable 51 requirements 72 external 52 © Copyright IBM Corp. 2004...
Page 184 90 Windows 23 removing 77 diskette drive FCC Class A notice 167 installing 58, 59, 61 features and specifications problems 104 Type 6220 5 removing 93 Type 6230 6 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 185 Type 6230 58 connector 72 hardware problems 17 field replacement units (FRUs) 125 heat output 5, 6 problems 105 IBM Configuration/Setup Utility program menu choices 12 CD-ROM drive activity 7 starting 11 diskette drive activity 7 using 11...
Page 186 POST error codes 109 extender card 90 power fan 77 button 85 front bezel 84 cables 44, 63 handle assembly 97 checkout 27 microprocessor 80, 88 control button 8 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 187 BIOS code 25 software using problems 109 Configuration/Setup Utility program 11 speaker 79 IBM Configuration/Setup Utility program 11 specifications IBM Enhanced Diagnostics diskette 22 desktop (Type 6220) 5 passwords 12, 13 tower (Type 6230) 6 Product Recovery program 20...
Page 188 73 connector 74 digital (DVI-I) connector 74 DVI connector 74 low force helical-60 (LFH-60) connector 74 specifications 5, 6 weight 5, 6 working with adapters 35, 54 IBM IntelliStation M Pro Types 6220 and 6230: Hardware Maintenance Manual...
Page 190 Part Number: 90P2681 (1P) P/N: 90P2681...

This manual is also suitable for:

6220 6230

IBM IntelliStation M Pro Hardware Maintenance Manual

Quick Links

Troubleshooting

Related Manuals for IBM IntelliStation M Pro

Summary of Contents for IBM IntelliStation M Pro

This manual is also suitable for:

Table of Contents