Driver Replacement; Wiring Diagrams - Cooper HALO HC8R Installation Instructions Manual

5. Connect white to white, black to black, and green
(from electrical service) on the supply side to the bare
copper wire in the junction box. Place all excess wiring
and connections into the junction box and replace the
cover. Place all connections and excess wiring into the
junction box and replace cover.
Driver
Figure 43.

Driver Replacement

To avoid possible electrical shock, be sure that the power is
turned off before installing or servicing this fixture.
The driver should be replaced by a qualified electrician.
●
The driver may be replaced either from below or above
●
the ceiling.
1. Remove trim assembly from the housing (Figure 40).
2. Remove the driver and junction box cover assembly.
(Figure 43).
3. Disconnect the wiring to the driver by undoing the
connectors then cut the red and blue wires.
4. Discard the old driver and junction box cover assembly.
5. Connect the new driver leads with the connectors.
6. Reattach the new driver and junction box cover
assembly.

Wiring Diagrams

For D010/D010347
Black (Line) Black (Line)
0-10V
White White
Dimming
(Neutral) (Neutral)
Driver
Ground
Installation Instructions – HC8R/HC812R Recessed LED Retrofit
Red
Red
Blue
LED
Purple
Black
Pink
Moudle Wiring
Diagram
0-10V
Dimming
Option (Field
Installation)
COOPER LIGHTING SOLUTIONS
* Constructions built before Jan 2022 may have gray wire
for 0-10 dimming control present. In these cases, the
installer will label the gray building wire as a 0-10 dimming
wire and connect to our product's pink 0-10V dimming
control wire. Reference NFPA70 (2020 NEC), section
410.69.
Dimming
The Halo Commercial HC8R/HC812R LED luminaire can be
dimmed however updates in dimmer technology and special
conditions may apply depending on the dimmer type being
used. For the latest information regarding dimmers for use
with this LED luminaire, please see the Halo Commercial
HC8R/HC812R LED Dimming Reference Sheet at
www.cooperlighting.com. In addition, you may wish to
consult the dimmer manufacturer for their latest dimmer
configurations and product information.
5-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR
STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting Solutions warrants to customers that, for a period
of five years from the date of purchase, Cooper Lighting Solutions
products will be free from defects in materials and workmanship. The
obligation of Cooper Lighting Solutions under this warranty is expressly
limited to the provision of replacement products. This warranty is
extended only to the original purchaser of the product. A purchaser's
receipt or other proof of date of original purchase acceptable to Cooper
Lighting Solutions. This is required before warranty performance shall be
rendered.
This warranty does not apply to Cooper Lighting Solutions products
that have been altered or repaired or that have been subjected to
neglect, abuse, misuse or accident (including shipping damages). This
warranty does not apply to products not manufactured by Cooper
Lighting Solutions which have been supplied, installed, and/or used in
conjunction with Cooper Lighting Solutions products. Damage to the
product caused by replacement bulbs or corrosion or discoloration of
brass components are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL COOPER LIGHTING SOLUTIONS BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
(REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT,
STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR
LOST PROFITS; NOR SHALL THE LIABILITY OF COOPER LIGHTING
SOLUTIONS FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR
CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE,
DELIVERY, USE, MAINTENANCE, REPAIR OR MODIFICATION OF
COOPER LIGHTING SOLUTIONS PRODUCTS, OR SUPPLY OF ANY
REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE
OF COOPER LIGHTING SOLUTIONS PRODUCTS GIVING RISE TO A
CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR
INSTALL FIXTURES.
All returned products must be accompanied by a Return Goods
Authorization Number issued by the Company and must be returned
freight prepaid. Any product received without a Return Goods
Authorization Number from the Company will be refused. Cooper
Lighting Solutions is not responsible for merchandise damaged in
transit. Repaired or replaced products shall be subject to the terms of
this warranty and are inspected when packed. Evident or concealed
damage that is made in transit should be reported at once to the carrier
making the delivery and a claim filed with them.
Reproductions of this document without prior written approval of
Cooper Lighting Solutions are strictly prohibited.
IB517061ML Installation instructions
7