Power 电源; User Controls 用户控制 - PRESONUS Temblor T8 Owner's Manual

2 Hookup
2.2 Hookup Diagrams
2.2 Rear-Panel Connections and Controls
2.1.3 Power 电源
2.1.4 User Controls 用户控制
0
4
IEC Power Connection: Your Temblor T8 accepts a standard IEC power cord.
IEC Power Connection:你的Temblor T8可以接受标准的IEC电源线。
Warning:Do not remove the centergrounding prong or use a separateground-lift
adapter, as this could result in electric shock.
警示：不要去掉中间的接地线或使用单独的接地线适配器，因为这可能
会导致电击。
Power Switch: This is the On/Off switch. The power status is indicated by the
illuminated logo on the front of the cabinet.
Power Switch: 这就是开/关。电源状态由机柜前面的发光标志来显示。
Power User Tip: Your Temblor T8 features a Standby mode. When no
signal is present for longer than ten minutes,your T8 will lowerits power
consumptionto less than 0.5W untilsignal is present again.The lighted
logo on the front of your T8 will turn white when Standby mode is active
用户提示：你的 Temblor T8 有一个待机模式。当超过 10 分钟没有信号
时，你的 T8 会将其功率消耗降低到 0.5W 以下，直到信号再次出现。
当待机模式启动时， T8 前面的发光标志将变成白色。
ACSelectSwitch:Theinput-powervoltageissetatthefactorytocorrespondwith
the country to which it was shipped. Use this switch only if you are using your
TemblorT8 in a country that uses a differentstandard voltage than is used in the
country where you purchased your T8.
ACSelectSwitch:输入电源电压在出厂时就已经设置好了，与运往的国家一
致。只有当你在一个使用不同标准电压的国家使用你的 Temblor T8 时，才
使用这个开关。
Polarity: The Polarity button reverses the polarity of the input signals.
Polarity: 极性按钮可以颠倒输入信号的极性。
PowerUser Tip:Once your have connected your T8 to your system, try experimenting
with each setting while listening to your favoritemusic.Leave this switch in the position
where the bass was the loudest.
用户提示：一旦你把 T8 连接到你的系统上，听最喜欢的音乐时，尝试一下每
个设置。把这个开关放在低音最响的位置。
HighPassFilter: Removesfrequencycontentbelow80Hzfromthefull-range
signalsentfrom theT8outputs.This is usefulif yourmain studio monitors donot
have their own highpass filter.
HighPassFilter: 从T8输出的全频信号中去除80Hz以下的频率内容。如果
你的主要演播室监听器没有自己的高通滤波器，这就很有用。
Power User Tip: Leaving frequency content below 80 Hz in full-range monitors
can cancel out or reinforce the highest frequencies that are reproduced by
the TemblorT8. This can make the bass response of the overallsystem muddy
and ill-defined. By rolling off your full-range speakers, you will create a more
linear frequency response between the subwooferand full-range content.
用户提示：将 80Hz 以下的频率内容留在全音域监听器中，可以抵消
或加强由 Temblor T8 再现的最高频率。这可能会使整个系统的低音响
应变得浑浊和不明确。通过对全频扬声器进行衰减，你将在低音炮和
全频内容之间创造一个更加线性的频率响应。
Temblor T8
Owner'sManual
Owner's Manual