Hookup 联机; What Is In The Box 包装内有什么; Rear-Panel Connections And Controls 后面板连接和控制 - PRESONUS Temblor T8 Owner's Manual

Active studio subwoofer
Hide thumbs Also See for Temblor T8:
Table of Contents

Advertisement

2
Hookup
2.1
What is in the Box
Hookup 联机
2
2.1
What is in the Box 包装里有什么
2.2
Rear-Panel Connections and Controls 后面板的连接和控制
2.1.1 Inputs
2.1.2 Outputs
In addition to this manual, your Temblor T8 package contains the following:
除本手册外,你的 Temblor T8 的包装还包括以下内容:
• (1) PreSonus Temblor T8 powered subwoofer
• PreSonus Temblor T8 有源超重低音扬声器
• (1) IEC power cable
• IEC电源线
Line-level Inputs: The Temblor T8 provides a choice of two input pairs: a pair
of balanced ¼"TRS inputs and one pair of RCA unbalanced inputs. When both
connections arein use,the RCA inputs will sum intotheTRSconnections.
Line-level Inputs: Tembl o rT8提供两种输入组的选择:一对¼"TRS平衡输入和一对
RCA非平衡输入。当两个连接都在使用时,RCA输入将汇总到TRS连接。
Power User Tip: Connect both the left and right inputs if you are connecting your full-
rangemonitors to the T8's outputs, or if you're running your TemblorT8 independently
from a stereo source (such as the PreSonusMonitor Station). This will ensure that your
Temblor T8 receives the low-frequency content from both the left and right sides of a
stereo audio signal. If your audio source provides a mono or LFE output, you only need to
connect one input—either L or R.
用户提示:如果将你的全范围监听器连接到 T8 的输出,或者你从一个立体声源
(如 PreSonus 监听站)独立运行 Temblor T8 ,请同时连接左和右的输入。这将确
保你的 Temblor T8 接收是来自立体声音频信号左右两边的低频内容。如果你的
音源提供一个单声道或 LFE 输出,你只需要连接一个输入 -- L 或 R 。
2 1
Ground
[+]
3
[-]
XLR
TRS
Input Gain: Sets the level of the input signal before it is amplified.
输入增益:设定输入信号在被放大之前的电平。
Outputs: The Temblor T8 provides two pairs of outputs: a pair of balanced
¼"TRS outputs and a pair of RCA unbalanced outputs.The full-range signal
connectedtothestereoinputs ontheT8ispassedthroughtotheseoutputs.
Use these outputs to connect your main left and right studio monitors.
If the High Pass Filter switch is engaged, frequencies below 80 Hz are not sent from
these outputs.
Outputs: Temblor T8 提供两对输出:一对¼" TRS平衡输出和一对RCA非平衡
输出。连接到T8上的立体声输入的全音域信号,会被传递到这些输出。
如果高通滤波器开关被激活,低于80Hz的频率就不会从这些输出端发送。
Sleeve:
Ring: Tip:
Ground
[-]
[+]
Temblor T8
Owner's Manual
3

Advertisement

Table of Contents
loading

Table of Contents