Marantz SR5011 Service Manual page 158

Error USB Update Error
Details of Error code
Code Display
NACK received in response or
60 no response from Sub for the
Error**60
"P" command.
Mismatched Check Sum in
61 response or no response from
Error**61
Sub for the "I" command.
Failed to start up Sub in
62 Power On sequence during
Error**62
Update.
Failed to transit to Application
63
Error**63
Mode.
Failed to transit to Boot
64
Error**64
Loader Mode.
Write Enable Latch Bit not
80 set in Read after issuing the
Error**80
"WREN" command.
Block Erase failed in Read after
81
Error**81
issuing the "BE" command.
No Update Packet received
82
Error**82
from CY920 (Time Out).
Abnormal data in Update
83 Packet received from CY920
Error**83
(CRC Error).
Abnormal data in Update
84 Packet received from CY920
Error**84
(Packet No Error).
Setup failure of the XModem
85
Error**85
transfer method
Mismatched Check Sum in
86 Check Sum comparison after
Error**86
rewriting.
Remedies
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
---Checking the firmware version after updating---
retried, the device may be malfunction-
After updating the firmware, check the version.
ing.
See
Unplug and reconnect the AC plug, and
try again.
158
Error USB Update Error
Details of Error code
Code Display
A2 Unable to detect USB.
Error**A2
A3 No Firmware File in USB.
Error**A3
The Firmware File in the USB
A4 does not support your model
Error**A4
and area.
Error notification received
A6 while requesting the Firm-
Error**A6
ware Info.
Time Out while obtaining
A7
Error**A7
Firmware information.
Unable to detect USB for
AE
Error**AE
Firmware Download.
No Firmware File for Firmware
AF
Error**AF
Download.
Time Out in Download (writ-
B1 ing to SDRAM) for Firmware
Error**B1
Download.
Error notification received af-
B2
Error**B2
ter rewriting the CY920 Firm.
Error in Firmware Update
B3
Error**B3
(Time Out).
Failed to transit to Boot
B4
Error**B4
Loader Mode.
Failed to transit to Application
B5
Error**B5
Mode.
"1. Version Display Mode"
Remedies
Reinsert or try a new USB device, Un-
plug and reconnect the AC plug, and
try again.
Check the file, Unplug and reconnect
the AC plug, and try again.
Make sure the model name and area of
the Firmware File, Unplug and recon-
nect the AC plug, and try again.
Try a new USB device, Unplug and
reconnect the AC plug, and try again.
Unplug and reconnect the AC plug, and
try again.
Reinsert or try a new USB device, Un-
plug and reconnect the AC plug, and
try again.
Check the file, Unplug and reconnect
the AC plug, and try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.