IBM TS2900 Manual page 65

accessor error #1.
00B8
Code (H)
Reverse REV position (PP1) error (accessor
origin not detected or FWD position
detected). Suspect the P origin sensor, FWD
sensor, or P motor.
00B9 accessor error #2.
Forward FWD position (PP2) error (accessor
origin detected or FWD not detected).
Suspect the P origin sensor, FWD sensor, or P
motor.
00BA accessor error #3.
PUT/GET/bar code reader position
(PP4/PP5/PPBF/PPBR) error (accessor origin
or FWD detected, or cell full). Suspect the P
origin sensor, FWD sensor, or P motor.
00BC During initialization, the accessor origin is
not detected. Suspect the P origin sensor,
FWD sensor, or P motor.
00BD During accessor movement, the movement
stop condition is detected. Suspect the P
encoder sensor or P motor.
00BF No gap condition detected at the completion
of accessor operation. Suspect the centering
sensor, P origin sensor, FWD sensor, or P
motor.
00C0 accessor operation disabled because a
cartridge magazine was removed. Suspect
the magazine set sensor.
00C8 Centering calibration error #1.
During centering calibration, centering
sensor OFF condition is not detected.
Suspect the centering sensor or P motor.
00C9 Centering calibration error #2.
During centering calibration, centering
sensor ON condition is not detected. Suspect
the centering sensor, X motor, or P motor.
00D0 Checksum error detected during firmware
update.
00D1 Firmware ID error detected during firmware
update.
00D2 Boot information error detected during
firmware update.
00D3 Bar code reader is not in maintenance mode
during bar code reader firmware update
(operation interrupted). Suspect the bar code
reader cable connection.
00D9 Magazine failed to unlock. Suspect the
magazine or magazine sensor.
00DA I/O Station failed to unlock. Suspect the
magazine or magazine sensor.
00DD An error detected during bar code reader
firmware check. Suspect the bar code reader
cable connection.
00E0 Write operation not finished within 1 ms
when writing data to flash memory.
00E1 Clear operation not finished within 10
seconds when clearing a sector in flash
memory.
00E2 Error detected in tape library configuration
stored in flash memory.
00E3 Checksum error detected in flash memory.
60 TS2900 Tape Autoloader
CHK 00B8
Panel
Description
Indication
CHK 00B9
CHK 00BA
CHK 00BC
CHK 00BD
CHK 00BF
CHK 00C0
CHK 00C8
CHK 00C9
CHK 00D0
CHK 00D1
CHK 00D2
CHK 00D3
CHK 00D9
CHK 00DA
CHK 00DD
CHK 00E0
CHK 00E1
CHK 00E2
CHK 00E3
1. Check the accessor locking screw and remove it if it is installed. See
Action Required
the accessor locking screw.
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
1. Confirm that the magazine is closed.
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library operations
resume. See Running library verify
If the problem persists, see Contacting IBM technical
1. Confirm the firmware file version.
2. Reinstall the firmware file.
3. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
1. Initiate an inventory. See Table
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
1. Cycle the power supply and try again.
2. Manually unlock the magazine, remove the magazine from the library, and
inspect it for damage.
If not damaged, return it to the library and run Library Verify before
normal library operations resume. See
If damaged, replace the magazine.
1. Initiate an inventory. See Table
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library operations
resume. See Running library verify
If the problem persists, see Contacting IBM technical
Running library verify test.
Contacting IBM technical support.
Running library verify test.
Contacting IBM technical support.
test.
support.
Running library verify test.
Contacting IBM technical support.
2.
Running library verify test.
Contacting IBM technical support.
Running library verify test.
2.
Running library verify test.
Contacting IBM technical support.
test.
support.
Removing