IBM TS2900 Manual page 64

Code (H) Description
007C Drive does not enter EJECT state (and media
not ejected) within 200 seconds of a GET
command. Suspect the drive.
007D Drive does not enter MOUNT state within
200 seconds of a PUT command. Suspect
the drive or X motor.
007E Drive does not enter SET state within 3
seconds of a PUT command. Suspect the
drive or X motor.
007F Drive I/F or connection error occurs during a
PUT operation or GET operation. Suspect the
drive.
0080 X movement error #1.
During X movement, the target stop
position's origin sensor error detected.
Suspect the X origin sensor or X motor.
0081 X movement error #2.
During X movement, a motor sync error
detected. Suspect the X encoder sensor or X
motor.
0082 X movement error #3.
During initialization, a motor sync error
detected. Suspect the X encoder sensor or X
motor.
0083 During an eject operation or move operation
(to a storage position), the X origin sensor is
not detected. Suspect the X origin sensor or
X motor.
0084 During initialization, the X origin position is
not detected. Suspect the X origin sensor or
X motor.
0088 X calibration error #1.
During X calibration, centering sensor OFF
condition is not detected.
0089 X calibration error #2.
During X calibration, centering sensor ON
condition is not detected.
008F During X operation, the cartridge magazine
was removed. Suspect the magazine set
sensor.
00B0 Failed to detect media in the accessor at
completion of GET operation. Suspect the
centering sensor, X motor, or P motor.
00B1 No media is contained in the specified cell
(Cell Empty). Suspect the centering sensor, X
motor, or P motor.
00B2 Media detected in the accessor at
completion of centering check operation.
Suspect the centering sensor.
00B3 Media detected in the accessor at
completion of PUT operation. Suspect the
centering sensor.
Panel
Indication
CHK 007C 1. If the cartridge does not eject, try to unload the cartridge from the drive with
the Web User Interface (Manage Library > Unload) or the Operator Panel
(Commands > Unload). Move the cartridge from the drive to the I/O Station.
Remove the cartridge from the library and inspect for damage and replace, if
necessary.
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
CHK 007D Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library operations
resume. See
CHK 007E
If the problem persists, see
CHK 007F 1. Reseat all cables. See
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
CHK 0080 1. Check the accessor locking screw and remove it if it is installed. See
the accessor locking
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
CHK 0081
If the problem persists, see
CHK 0082
CHK 0083
CHK 0084
CHK 0088
CHK 0089
CHK 008F 1. Confirm that the magazine is closed.
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
CHK 00B0 1. Confirm the media is compatible. See
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
CHK 00B1 Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library operations
resume. See
If the problem persists, see
CHK 00B2 1. If the cartridge remains in the accessor, try to move the cartridge from the
accessor to the I/O Station with the Web User Interface or the Operator Panel.
Remove the cartridge from the library and inspect for damage and replace, if
necessary.
CHK 00B3
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
Action Required
Running library verify
Contacting IBM technical
Running library verify test.
Contacting IBM technical
Reseating cables.
Running library verify
Contacting IBM technical
screw.
Running library verify
Contacting IBM technical
Running library verify
Contacting IBM technical
Table 1.
Running library verify
Contacting IBM technical
Running library verify test.
Contacting IBM technical
Running library verify
Contacting IBM technical
TS2900 Tape Autoloader 59
test.
support.
support.
test.
support.
Removing
test.
support.
test.
support.
test.
support.
support.
test.
support.