IBM TS2900 Manual page 63

Code (H)
0041 A hardware error detected upon media
insertion.
0042 A drive load timeout error detected upon
insertion.
0048 Incompatible medium installed.
0053 Response acknowledge error received from
bar code reader. Suspect the bar code reader
cable connection.
0056 Receive data checksum error received from
bar code reader. Suspect the bar code reader
cable connection.
0057 Invalid data received from bar code reader.
Suspect the bar code reader cable
connection.
0058 A bar code reader read-error detected.
Suspect the bar code reader cable
connection.
0059 A bar code reader FLASH control error
detected. Suspect the bar code reader cable
connection.
005A A bar code reader diagnostics error detected.
Suspect the bar code reader cable
connection.
2
005B
I C I/F error. A transfer retry detected.
Suspect the bar code reader cable
connection.
005C 2
I C I/F error. Interrupt timeout detected.
Suspect the bar code reader cable
connection.
2
005D
I C I/F error.
Invalid signal (NAK) detected. Suspect the
bar code reader cable connection.
2
005E
I C I/F error.
Bus arbitration lost error detected. Suspect
the bar code reader cable connection.
005F 2
I C I/F error.
Ready condition does not occur. Suspect the
bar code reader cable connection.
0070 Calibration failed because the accessor
contains media. Suspect the centering
sensor.
0071 Calibration failed due to an empty magazine.
Suspect the magazine set sensor.
0072 Calibration measurement invalid data error.
Suspect the centering sensor, X motor, or P
motor.
0074 GET, centering check, or bar code reader
read operation failed because the accessor
contains media. Suspect the centering
sensor.
0075 PUT operation failed because the accessor
contains no media. Suspect the centering
sensor.
58 TS2900 Tape Autoloader
Panel
Description
Indication
CHK 0041
CHK 0042
CHK 0048
CHK 0053
CHK 0056
CHK 0057
CHK 0058
CHK 0059
CHK 005A
CHK 005B
CHK 005C
CHK 005D
CHK 005E
CHK 005F
CHK 0070
CHK 0071
CHK 0072
CHK 0074
CHK 0075
Action Required
1.
2. Verify that the cartridge is not write-protected. See
3. If it is a cleaning cartridge, verify that the cartridge is not expired. See
cartridge.
4. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library operations
resume. See Running library verify
If the problem persists, see Contacting IBM technical
Verify that the cartridge is compatible with the drive installed in the library. See
1.
If the problem is corrected, run Library Verify before normal library operations
resume. See Running library verify
If the problem persists, see Contacting IBM technical
1. Initiate an inventory. See Table
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
1. Attempt to unload the cartridge from the accessor. See
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
If the problem persists, see
Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library operations
resume. See Running library verify
If the problem persists, see Contacting IBM technical
Write-Protect switch.
Running library verify test.
Contacting IBM technical support.
test.
support.
test.
support.
2.
Running library verify test.
Contacting IBM technical support.
Table 5
Running library verify test.
Contacting IBM technical support.
test.
support.
Cleaning
Table