Marantz SR5014 Service Manual page 145

1.6. Confirmation items for the video system
See the block diagram fig.VXXth.
Paths to be confirmed Display
V01VIDEO
fig.V01
1 Analog Video pass
***.*
Video Convert
V02CONV
2 fig.V02
(HDMI ⇒ HDMI)
***.*
HDMI pass
V03HDMI
3 fig.V03
(MAIN ZONE)
***.*
HDMI CEC
V04CEC
4 (Control Monitor : fig.V04
***.*
HDMI Monitor1)
fig.V05a
HDMI Audio
V05H-AVR
5
fig.V05b
(Audio : AVR)
***.*
HDMI Audio
V06H-TV
6 fig.V06
(Audio : TV)
***.*
V07MENU
7 GUI fig.V07
***.*
Settings
Input Source : CBL/SAT
Video Convert : Off (IP Scaler : Off), All sources
MAIN ZONE : On
ZONE2 : On
Input Source : CBL/SAT
Video Convert : On, All sources
IP Scaler : "Analog & HDMI", All sources
Resolution : "Auto", All sources
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
Video Convert : Off (IP Scaler : Off), All sources
Video Mode (IP Scaler) : Bypass
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
HDMI Control : On
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
HDMI Control : Off
HDMI Audio : AVR (if checking the audio output from
AVR)
HDMI Audio : TV (if checking the audio output from TV) • HDMI input (PCM, DolbyDigital, DTS) ⇒ HDMI output (audio output from connected TV)
Input Source : CBL/SAT
Video Convert : Off (IP Scaler : On), All sources
IP Scaler : "Analog & HDMI", All sources
Resolution : "Auto", All source
Setup Menu : On
MAIN ZONE : On
ZONE2 : Off
145
What to confirm
• CVBS input ⇒ CVBS output
• Component input ⇒ Component output
( b The input source can be switched to any source except CBL/SAT.)
• CVBS input ⇒ IP Scaler ⇒ HDMI output.
• Component input ⇒ IP Scaler ⇒ HDMI output.
• HDMI input (except 4K60p) ⇒ IP Scaler ⇒ HDMI output (except 4K60p)
• HDMI input (4K60p) ⇒ HDMI output (4K60p) & Vol display
• ETHERNET input ⇒ IP Scaler ⇒ HDMI output.
( b The input source can be switched to any source except CBL/SAT.)
• HDMI input (MAIN function) ⇒ HDMI output (MAIN)
( b The input source can be switched to any source except CBL/SAT.)
• When the power supply of a TV is put in the standby mode, make sure that the power supply
of this unit is also put in the standby mode.
( b The input source can be switched to any source except CBL/SAT.)
• The ARC path can also be checked (check this using the TV input source).
• HDMI input (PCM, DolbyDigital, DTS) ⇒ Speaker output.
• HDMI input(HD audio) ⇒ Speaker output.
( b The input source can be switched to any source except CBL/SAT.)
( b The input source can be switched to any source except CBL/SAT.)
• GUI display ⇒ HDMI output.
( b The input source can be switched to any source except CBL/SAT.)