Correct Usage; Timer Operation - Toshiba MCY-MHP0506HT Owner's Manual

1FAN_OM_EHV0000101-01.book Page 8 Thursday, September 13, 2018 5:10 PM
4

Correct Usage

When you use the air conditioner for the first time or
change the settings, follow the procedures below.
From next time, pushing the button starts
running of the air conditioner with the chosen settings.
Preparation
Turn on the power switch
• When turned on, the separation line appears and
blinks on the remote controller display.
* The remote controller will not work for about 1
minute after turning on the power. This is not a
malfunction.
REQUIREMENT
• Keep the power switch turned on during use.
• When you resume using the air conditioner after a long
period of disuse, turn on the power switch at least 12
hours before starting running.
Operations
TEMP. ON / OFF
1
TIMER SET FAN MODE
2
TIME SAVE VENT
FILTER
RESET TEST SET CL SWING/FIX UNIT LOUVER
1
Push the button.
The operation lamp lights up.
2
Push the "MODE " button to select a
operation mode.
Each time you push the button, the operation mode
and its icon change in the following order:
Heat Dry Cool Fan
(Dehumidify)
EN-15
3
Push the button to stop running.
The operation lamp turns off.
Changing the fan speed
1
Push the "FAN " button to select a fan
speed.
• Each time you push the button, fan speed and its
indication change in the following order:
(" Auto" cannot be selected in the FAN
mode.)
Auto High Medium Low
• When heating, if the room does not heat up using
" Low", select " High" or " Medium".
• The temperature sensor detects the return air
temperature at the indoor unit, which may slightly
differ from the actual room temperature
depending on installation condition. Set
temperature is a target of room temperature.
Changing the set Temperature
1
Push the "TEMP. " buttons.
Push to increase the temperature, and to
decrease the temperature. (The set temperature
cannot be changed in the fan mode.)
NOTE
When cooling
Running starts in approximately 1 minute.
When heating
• The air conditioner may continue running in the fan
mode for about 30 seconds after stopping heating.
• The heated air comes out after a 3 to 5 minutes of pre-
heating with the indoor fan kept turned off. (The pre-
heat indicator is displayed on the remote
controller.)
• The fan speed becomes extremely low when the room
temperature has reached the set temperature.
– 8 –
5

Timer Operation

Select a timer type from the following three: (Max. 168 hours)
OFF timer : Stops running after the specified period.
Repeat-OFF timer : Stops running after the specified period every time you use the air conditioner.
On timer : Starts running after the specified period.
Setting the timer
1
3
1
Push the button.
Each time you push the button, the timer mode and
indication change in the following order:
Off On
Off
(Off timer) (Repeat Off timer) (On timer)
No indication (Timer
function is deactivated)
• and the time indicator blink.
2
Push the buttons to set the period of time
until the timer actions.
• The time setting increases in 0.5-hour (30-minute)
increments each time you push .
The setting increases in 1-hour increments if it is
over 1d (24 hours). The maximum is 7d (168
hours).
On the remote controller, settings between 0.5h
and 23.5h (*1) are displayed as is.
If it is over 24 hours (*2), the days and hours
appear.
• The time setting decreases in 0.5-hour (30-
minute) decrements (0.5 hours to 23.5 hours) or
1-hour decrements (24 hours to 168 hours) each
time you push .
Example of remote controller display
• 23.5 hours (*1)
Owner's Manual
2
• 34 hours (*2)
indicates 1 day
(24 hours).
Days Hours
indicates 10 hours.
(Total: 34 hours)
3
Push the button.
disappears, the time indication is displayed,
and or display flashes.
(When using the ON timer, all indications other than
the time and turn off.)
Cancelling the timer
1
Push the button.
The timer indicator disappears.
NOTE
• When using Repeat OFF timer, pushing the
button after stopping by the timer starts running again
and the timer will stop the running again after the
specified period.
• When using OFF timer, the timer indication temporarily
disappears for about 5 seconds by pushing the SWING/FIX
button. This occurs due to the processing in the
remote controller, and is not a malfunction.
EN-16