Toshiba MCY-MHP0506HT Owner's Manual page 8

1FAN_OM_EHV0000101-01.book Page 7 Thursday, September 13, 2018 5:10 PM
1
2
3
4
5
6
22
15
17
9
Swing indicator
Displayed during up / down movement of the louver.
10
Set temperature display
The selected set temperature is displayed.
11
Remote controller sensor indicator
Displayed when the remote controller sensor is
used.
12
Pre-heat indicator
Displayed when the heating mode is energized or
defrost cycle is initiated.
While this indication is displayed, the indoor fan
stops or operate in fan mode.
13
No function indicator
Displayed when the function requested is not
available on that model.
14
Fan speed indicator
Indicates the selected fan speed:
(Auto)
(High)
(Medium)
(Low)
15
Louver Number display
(example:01, 02, 03, 04)
16
Power saving mode display
Displayed during capacity saving mode.
17
Louver lock indicator
Displayed when a louver is locked. (4-way cassette
type only)
EN-13
19 18
7 8 9 16
10
20
11
21
12
14
13
18
UNIT No. display
Displays the number of the indoor unit selected.
Also displays error code of indoor and outdoor units.
19
Central control indicator
Displayed when the air conditioner is controlled
centrally and used with central control devices such
as the central remote controller.
If the use of the remote controller is prohibited by
the central control, blinks when the ON/OFF,
MODE, or TEMP. button on the remote controller is
pushed, and the buttons do not function.
(Settings that can be configured on the remote
controller differ depending on the mode of the
central control. For details, read the Owner's
Manual of the central remote controller.)
20
Operation mode controlled indicator
Displayed when MODE button is pushed while
operation mode is fixed to cool or heat by the air
conditioner administrator.
21
Operation ready display
This display appears on some models.
22
Service display
Displayed while the protective device works or a
trouble occurs.
– 7 –
Operation section
Once the settings have been configured, all you need to do is push the
12
2
5
3
1
button (Fan speed select button)
Selects the desired Fan speed.
* Not available for the concealed duct high static
pressure. Only "High" is displayed.
2
button (Timer set button)
Use to setup the timer.
3
button (TEST button)
Use only for service.
(During normal operation, do not use this button.)
4
button
Use when a ventilator (commercially-available) is
connected. Push the button to turn on/off the
ventilator. Turning on/off the air-conditioner also
turns on/off the ventilator.
* No ventilator is connected if " " appears on the
remote controller display after pushing the
button.
5
button (Filter reset button)
Resets " FILTER" indication after cleaning.
6
button (Power save operation)
Use to initiate power saving mode.
7
SWING/FIX button
Use to select automatic swing or fixed louver
position.
* Not available for concealed duct, slim duct, floor
standing concealed and floor standing cabinet.
Owner's Manual
button from then on.
1 8
9
10
4
11
7 6
8
Operation lamp
Lights up during running.
Blinks when an error occurs or the protective device
activates.
9
button
Turns on the unit when pushed, and turns off when
pushed again.
10
button (Operation mode select button)
Selects desired operation mode.
11
UNIT LOUVER button (Unit / Louver select button)
Selects a unit number (left) and louver number (right).
UNIT button:
If two or more indoor units are controlled by one
remote controller, use this button to select a unit to
adjust its air blow direction.
LOUVER button: (4-way cassette type 2H series only)
Selects a louver to control when adjusting the louver lock
setting or wind direction setting separately for each louver.
12
button
Adjusts the set temperature.
Select the desired set point by pushing
TEMP. or .
OPTION:
Remote controller sensor
Normally the temperature sensor of the indoor unit senses the
temperature. The temperature around the remote controller
can also be sensed. For details, contact your dealer.
* Do not use the function when the air conditioner is
controlled in a group.
EN-14