Panasonic SC-MAX7000 Operating Instructions Manual page 20

█
Bluetooth
®
Pairing cannot be done.
•
Check the Bluetooth
•
The device is out of the 10 m communication range. Move
the device nearer to the system.
The device cannot be connected.
•
The pairing of the device was unsuccessful. Do pairing
again.
• The pairing of the device has been replaced. Do pairing
again.
•
This system might be connected to a different device.
Disconnect the other device and try pairing the device
again.
•
The system may have a problem. Switch off the system and
then switch on again.
The device is connected but audio cannot be heard
through the system.
•
For some built-in Bluetooth
audio output to "SC-MAX9000", "SC-MAX7000" or
"SC-MAX5000" manually. Read the operating instructions
of the device for details.
Sound from the device is interrupted.
•
The device is out of the 10 m communication range. Move
the device nearer to the system.
•
Remove any obstacle between the system and the device.
•
Other devices that use the 2.4 GHz frequency band
(wireless router, microwaves, cordless phones, etc.) are
interfering. Move the device nearer to the system and
distance it from the other devices.
•
Select "MODE 1" for stable communication.
The one-touch connection (NFC) is not working.
•
Make sure the system and the NFC feature of the device
are switched on.
• Touch and hold the device on the NFC touch area of this
system again.
Playback image and sound are not synchronized.
•
Restart the playback app of the device
•
Connect the device to the system with an audio cable (not
supplied).
█
Radio
Sound is distorted.
•
Use an optional FM outdoor antenna. The antenna should
be installed by a competent technician.
A beat sound is heard.
•
Switch off the TV or move it away from the system.
• Move mobile telephones away from the system if the
interference is apparent.
•
When in AM tuner mode, select the "B.PROOF" setting that
provides the best reception.
A low hum is heard during AM broadcasts.
•
Move the antenna away from other cables and cords.
█
Main unit displays
"ADJUST CLOCK"
•
The clock is not set. Adjust the clock.
"ADJUST TIMER"
•
The play timer and/or record timer is not set. Adjust the
play timer and/or record timer.
"ALB FULL"
•
The number of albums has exceeded the supported limit.
20
device condition.
®
® devices, you have to set the
"AUTO OFF"
• The system has not been used for 20 minutes and will
switch off within a minute. To cancel, press any button.
"CAN'T REC"
"DEVICE FULL"
•
You cannot do recording because the remaining recording
time of the USB device is less than the total time of the
music source. Change to a USB device which has enough
recording time and do the recording again.
"ERROR"
•
An incorrect operation was done. Read the instructions and
try again.
"ERROR" (during recording)
• You cannot select other playback source (example: radio,
USB etc.) or press [2] or [6] during recording. Stop
the recording function.
•
You cannot open the disc tray when recording from an AM
source.
"F61"
• Examine and correct the speaker cords connection.
•
Disconnect the USB device. Switch off the system and then
switch on again.
"F703"
•
Examine the Bluetooth
®
•
Disconnect the Bluetooth
and then switch on again.
"F76"
•
There is a problem with the power supply.
• Disconnect the AC power supply cord and consult your
dealer.
"F77"
•
Disconnect the AC power supply cord and consult your
dealer.
"NO DEVICE"
•
You cannot do recording or check available storage space
because there is no USB device connected to
"NO DISC"
• You have not put in a disc.
"NO PLAY"
"UNSUPPORT"
•
Examine the content. You can only play supported format.
•
The files in the USB device can be corrupted. Format the
USB device and try again.
•
The system may have a problem. Switch off the system and
then switch on again.
"NO TRACK"
•
There is no album or track in the USB device or the internal
memory.
"PLAYERROR"
•
An unsupported MP3 file has been played. The system will
skip that track and play the next one.
"REC ERROR"
•
You disconnected the USB device during recording.
Connect the USB device and do recording again.
•
An error occurred during USB recording. Disconnect the
USB device and then connect it again.
"REMOTE 1"
"REMOTE 2"
• The remote control and the main unit are using different
codes. Change the code of the remote control.
–
When "REMOTE 1" is shown, press and hold [OK] and
[1] for a minimum of 4 seconds.
–
When "REMOTE 2" is shown, press and hold [OK] and
[2] for a minimum of 4 seconds.
connection.
device. Switch off the system
®
USB B
.