Denon DHT-1000DV Operating Instructions Manual page 29

(2) Tuning
2 3 1
Example: Tuning in FM/AM stations
Before operating the remote control unit!
TUNER/TV/VCR
Be sure to press the proper remote control
mode selector button to set the remote control
unit to the AV mode.
1 Turn the FUNCTION/SELECT knob of the main unit or
press the FUNCTION button of the remote control and
select "TUNER".
FUNCTION
/ SELECT FUNCTION
Main unit Remote control unit
2 Select "FM" or "AM".
• The selected "FM AUTO", "FM MONO" or "AM" is
displayed.
• When using the remote control, the mode button is
used to select FM AUTO and MONO.
BAND
MODE
BAND
Main unit Remote control unit
POWER
VCR POWER
TV POWER
MENU FUNCTION
1
ENTER
2
MODE
2 VOLUME
BAND
MUTE
CH SHIFT
NTSC/PAL STATUS
3
TU MEMO
SUB TITLE AUDIO ANGLE TOP MENU
3 Adjust the receiving frequency.
• When a station is received, the "TUNED" indication
will light.
TU
- TUNING +
Main unit Remote control unit
NOTE:
A humming sound may be heard when using a TV nearby
while receiving AM programs. If this happens, move the
system as far from the TV as possible.
Auto tuning
• When one of the Tuning +/– button is pressed, the
frequency changes in steps of 50 kHz in the FM band,
9 kHz in the AM band.
• If one of the Tuning +/– button is held for over 1 second,
the frequency continues to change when the button is
released (auto tuning) and stops when a station is tuned
in.Tuning will not stop at stations whose reception is
poor.
• To stop the auto tuning function, press the Tuning +/–
button once.
FM Stereo Reception
• When a program being broadcast in "FM AUTO" is
received, the "ST" indicator lights and the program is
received in stereo.
• If reception is poor and there is much noise in the
stereo signals, press the BAND or MODE button to set
the FM MONO mode.
POWER
(3) Presetting FM and AM stations
VCR POWER
TV POWER
Example: Presetting FM station (currently tuned in) at preset number P03
MENU FUNCTION
ENTER
MODE
VOLUME
BAND
2
2
MUTE
CH SHIFT
NTSC/PAL
STATUS
1,3
TU MEMO
SUB TITLE AUDIO ANGLE TOP MENU
PROG/DIRECT REPEAT A-B REPEAT RANDOM
CH.SELECT T.TONE SDB/TONE SURR.PARA
SETUP CDR/MD/TAPE TUNER/TV/VCR DVD
REMOCON MODE
Before operating the remote control unit!
TUNER/TV/VCR
Be sure to press the proper remote control
mode selector button to set the remote control
unit to the AV mode.
1 Tune in the broadcast station that is to be preset and
press the Memory button.
• A "P0–" ("P1–", "P2–" or "P3–") indication flashes
for 10 seconds.
NTSC/PAL
MEMO
Remote control unit
Presetting
• Up to 40 AM or FM stations can be preset using this procedure.
• In addition to the reception frequency, the reception mode (monaural or auto) is also preset, so check the display when
presetting stations.
• If a station is preset at a number where a station is already preset, the previous station is replaced with the new station.
• The preset memory is not cleared when the power cord is unplugged.
(4) Listening to preset stations
POWER
VCR POWER
Example: Listening to the station preset at number P03 (This operation is only possible from the remote control unit.)
TV POWER
MENU FUNCTION
ENTER
MODE
VOLUME
BAND
1
1
MUTE
CH SHIFT
NTSC/PAL STATUS
TU MEMO
SUB TITLE AUDIO ANGLE TOP MENU
PROG/DIRECT REPEAT A-B REPEAT RANDOM
T.TONE SDB/TONE SURR.PARA
CH.SELECT
SETUP CDR/MD/TAPE TUNER/TV/VCR DVD
ENGLISH
2 While the "P0–" ("P1–", "P2–" or "P3–") indication is
flashing, use the shift button and the channel (CH)
buttons (–, +) to display the preset number "P03".
Each press of the shift button adds 10 to the current preset
number in the range of P01 to P40.
Example:
Starting with a P13
setting, each press of
CH SHIFT
the shift button results
in the changes P13 /
P23 / P33 / P03 /
P13 /... Remote control unit
Example:
Starting with a P0– setting, each press of the shift button
results in the changes P0– / P10 / P20 / P30 / P40 /
P10 /...
3 Press the MEMORY button while the "P03" display is
flashing.
• The "P03" display will light and presetting will be
completed.
NTSC/PAL
MEMO
Remote control unit
Before operating the remote control unit!
TUNER/TV/VCR
Be sure to press the proper remote control
mode selector button to set the remote control
unit to the AV mode.
1 Press the remote control shift button and the channel
(CH) button (–, +) and select preset number "P03".
CH SHIFT
Remote control unit
29