Denon DHT-1000DV Operating Instructions Manual page 20

ENGLISH
4 Start playback on the selected component.
• For operating instructions, refer to the component's
manual.
5 Either turn the MASTER VOLUME dial on the main unit
or use the VOLUME buttons on the remote control unit
to adjust the volume.
The volume level is displayed on
the display.
MASTER VOLUME
Main unit Remote control unit
• The volume can be adjusted within the range of -60
to 0 to +18 dB. Note that depending on the input
signal, surround mode, speaker settings and channel
level setting, it may not be possible to adjust the
volume up to +18 dB.
Input mode when playing DTS sources
• If DTS-compatible CDs are played in the "PCM" mode,
noise is output because DTS playback is not possible.
To play a DTS-compatible source, be sure to set the
input mode to "AUTO" or "DTS".
• Noise may be generated at the beginning of playback
and while searching during DTS playback in the AUTO
mode. If so, play in the DTS mode.
To check the currently playing program
2
source, etc.
Press the STATUS button.
FUNCTION
/ SELECT
STATUS
\
Main unit Main unit
To perform this operation on the main unit, press the
STATUS button, then turn the FUNCTION/SELECT
knob.
The current program source and surround settings are
shown on the display each time the button is pressed.
(When the function is set to DVD, the information is also
displayed on the TV screen.)
20
Input mode display
DIG AUTO
• In the AUTO mode
ANA
• In the DIGITAL
DIG AUTO
ANA
PCM mode
• In the DIGITAL
DIG AUTO
ANA
DTS mode
DIG AUTO
• In the ANALOG
ANA
mode
VOLUME
Input signal display
• DOLBY DIGITAL
DIG PCM
DIGITAL
• DTS
DIG PCM
DIGITAL
• PCM DIG
PCM
DIGITAL
• "DIG" lights when digital signals are input properly. If "DIG"
is flashing, check whether the connections are proper and
whether the input component's power is on.
Input mode when playing DTS sources
• When playing CDs containing recordings of live
concerts, etc., in the "AUTO" mode, the sound may be
slightly broken at the beginning. If this happens, switch
to the "PCM" mode.
STATUS
Remote control
unit
After starting playback
Lit
[1] Adjusting the sound quality (SDB / TONE)
PCM DTS
The SDB/TONE function will not work in the direct mode.
One of these lights, depending
on the input signal.
POWER
PCM DTS
VCR POWER
TV POWER
PCM DTS
2
PCM DTS
MODE
BAND
SUB TITLE
PROG/DIRECT REPEAT A-B
DTS
CH.SELECT
PRO LOGIC II
SETUP
One of these
lights,
DTS
1 Press the SDB/TONE button.
depending on
the input signal.
• The tone switches as follows each time the
SDB/TONE button is pressed.
DTS
SDB/TONE
Main unit
DEFEAT
2 With the name of the volume to be adjusted selected,
turn the FUNCTION/SELECT knob or cursor button (
, ) to adjust the level.
FUNCTION
/ SELECT
Main unit
DEFEAT
• The signals do not pass through the SDB, bass and
treble adjustment circuits, providing higher quality
sound.
SDB
• Either turn the FUNCTION / SELECT dial or use the
( , ) cursor buttons to select "ON" or "OFF".
BASS, TREBLE
• To increase the bass or treble: Turn the control
clockwise or press the cursor button. (The bass or
treble sound can be increased to up to +10 dB in
steps of 2 dB.)
• To decrease the bass or treble: Turn the control
clockwise or press the cursor button. (The bass or
treble sound can be decreased to up to –10 dB in
steps of 2 dB.)
If no operation is performed within 4 seconds, the
display switches back to what was previously
displayed.
[2] Turning the sound off temporarily (MUTING)
2 1
2
ENTER
VOLUME
MUTE
CH SHIFT
NTSC/PAL STATUS
1 Use this to turn off the audio output temporarily.
TU MEMO
AUDIO ANGLE TOP MENU
Press the MUTE button.
REPEAT RANDOM
Cancelling MUTE mode.
T.TONE SDB/TONE SURR.PARA
Press the MUTE button again.
1
CDR/MD/TAPE TUNER/TV/VCR DVD
SDB/TONE
NOTE:
• The setting is cancelled if the set's power is turned off.
Remote control unit
[3] Listening over head phones
SDB BASS TREBLE
(ON/OFF)
1
1 Connect the headphones to the PHONES jack of the
front panel.
The output to the speaker automatically is turned
off and no sound is produced from the speakers.
Remote control unit
POWER
VCR POWER
TV POWER
MODE
VOLUME
BAND
1
MUTE
CH SHIFT
NTSC/PAL STATUS
TU MEMO
SUB TITLE AUDIO ANGLE TOP MENU
PROG/DIRECT REPEAT A-B REPEAT RANDOM
CH.SELECT T.TONE SDB/TONE SURR.PARA
SETUP CDR/MD/TAPE TUNER/TV/VCR DVD
REMOCON MODE
MUTE
Remote control unit
PHONES