Table of Contents
Advertisement
4. Confirm on the personal computer that the unit is detected as a connectable wireless network.
5. To further confirm that the unit is connectable, connect the unit to the personal computer and double-click the "current connection"from the icon
displayed on the notice field, make sure that the unit is displayed in the Wireless internet access column.
1-4. PRECAUTION ON REPLACING THE LD-1014 BOARD
Angular Velocity Sensor
When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor SE7701 (PITCH/YAW).
Start the Adjust Manual in the Adjust Station and execute the "GYRO sensor sensitivity adj".
LD-1014 BOARD (SIDE A)
Y: YAW sensor sensitivity
P: PITCH sensor sensitivity
Type A:
SE7701
Type B:
Note: The sensor sensitivity of SE7701 (PITCH/YAW) on LD-1014 board is written only repair parts.
HDR-PJ800/PJ810/PJ810E/PJ820/PJ820E_L2
1-5. SELF-DIAGNOSIS FUNCTION
1-5-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the Viewfinder or the LCD
screen what to do.
This function consists of two display; self-diagnosis display and service
mode display. Details of the self-diagnosis functions are provided in the
Instruction manual.
Viewfinder or LCD screen
Blinks at 3.2 Hz
C
3 2
0 0
Repaired by:
Block
C : Corrected by customer
Indicates the appropriate
E : Corrected by service
step to be taken.
engineer
E.g.
13 ....
Format the "memory card".
32 ....Turn on power again.
1-5-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Block
Detailed
Function
Code
C
0
4
0
0
Non-standard battery is used.
C
0
6
0
0
The battery pack temperature is high.
Memory card is unformatted.
C
1
3
0
1
Memory card is broken.
C
1
3
0
2
*
Access error
C
1
3
0
3
*
Access error (External media)
C
1
3
0
4
*
Drive fault (External media)
C
3
2
6
0
Difficult to adjust focus
(
E
6
1
0
0
)
(Cannot initialize focus)
E
2
0
0
0
Flash memory data are rewritten.
E
3
1
0
0
Drive fault
*
Note 1: Start the Adjust Manual in the Adjust Station and refer to the "DESTINATION DATA WRITE".
Note 2: Functions of codes with * mark are not provided in this unit.
1-2
1-5-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
Viewfinder or the LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character display
indicates the "repaired by:", "block" in which the problem occurred, and
"detailed code"of the problem.
Detailed Code
Refer to "1-5-3. Self-diagnosis Code Tabl e".
Correction
Use the InfoLITHIUM battery.
Change the battery pack or place it in a cool place.
Format the memory card.
Insert a new memory card.
Remove the power source. Reconnect it again and operate your cam-
corder again.
Turn power off and turn power on again.
Turn power off and turn power on again.
Retry turn the power on by the power switch. If it does not recover,
check the focus MR sensor of lens block (pin es, rs of CN6801 on the
LD-1014 board). If it is OK, check the focus motor drive IC (IC6800 on
the LD-1014 board).
Make flash memory data correct value. (Note 1)
Turn power off and turn power on again.
– ENGLISH –
Advertisement
Table of Contents
