Error Messages; On The Unit's Display - Panasonic DMR-EZ28K Operating Instructions Manual

Error Messages

On the Unit's Display

H , F
(" " stands for a service
number.)
RC (" " stands for a
number.)
HARD ERR
("HArd" and "Err" are
alternately displayed.)
NO READ
("NO" and "REAd" are
alternately displayed.)
FULL
UNSUPPORT
("UNSUP" and "POrt" are
alternately displayed.)
UNFORMAT
("UNFOr" and "MAt" are
alternately displayed.)
" " is displayed on the
unit's display.
F74
F75
U59
U61
U72
U73
U76
U88
U99
68
RQT9046
• An error has occurred. The number following "H" or "F" depends on the status of the unit.
Check the items below and in the Troubleshooting Guide. If the service number still does
not disappear after the check, reset the unit (➔ 70, "To restore the unit if it freezes" ).
• If the service numbers fail to clear, note the service numbers and
contact a qualified service person.
• The remote control and the main unit are using different codes.
Change the code on the remote control.
• If there is no change after turning the unit on and off, consult the
dealer where the unit was purchased.
• The disc is dirty or badly scratched. The unit cannot record, play, or edit.
• The disc may be incompatible or of poor quality.
• You have used a lens cleaner and it has finished operation. Press
[ ; OPEN/CLOSE] on the main unit to eject the disc.
• Displayed when the unit is started. This is not a malfunction.
• The unit is carrying out its recovery process. You cannot operate the
unit while " " is displayed.
• There are already 16 scheduled recording programs. Delete
unnecessary scheduled recording programs.
• You have inserted a disc the unit cannot play or record on.
• You tried to operate with a non-compatible USB memory.
• You have inserted a new DVD-RW/+RW or a DVD-RAM/DVD-RW
(DVD-Video format) recorded on other equipment. You can format the
disc when the format confirmation screen is displayed.
• This unit is confirming that it is connected with equipment compatible
with HDAVI Control.
• The HDMI connection could not be authenticated due to a transfer
malfunction. Consult the dealer where the unit was purchased.
• The HDMI connection could not be authenticated due to an internal
data malfunction. Consult the dealer where the unit was purchased.
• The unit is very warm.
The unit switches to standby for safety reasons. Wait for about 30 minutes
until the message disappears. Reinstall the unit in an area with adequate
ventilation. Do not block the cooling fan on the rear of the unit.
• There was a power failure or the AC power supply cord was disconnected while the
unit was on. The unit is carrying out its recovery process. This process restores the
unit to normal operation. The unit is not broken. Wait until the message disappears.
• The HDMI connection acts unusually.
– The connected equipment is not HDMI compatible.
– Please use HIGH SPEED HDMI cables that have the HDMI logo (as shown on the cover).
– The HDMI cable is damaged.
• HDMI cannot be output because you are connected to a model that
does not support copyright protection.
• There was something unusual detected with the disc while recording
or playing; there was a power failure or the AC power supply cord
was disconnected while the unit was on. The unit is carrying out its
recovery process. This process restores the unit to normal operation.
The unit is not broken. Wait until the message disappears.
• The unit fails to operate properly. Press [POWER ^ /I] on the main unit to switch
the unit to standby. Press [POWER ^ /I] on the main unit again to turn the unit on.
Page
−
−
48
−
63
62, 63,
65
3
−
−
23
62, 63
64
21, 44
−
−
−
−
−
−
−
71
−