Rear Panel - Sony HKCU-IP43F Operation Manual

Rear Panel

1
7
a TRUNK A connector (round 12-pin)
Used to connect to the CCU connector on a video camera via
an RS-232C or RS-422A interface. Communication with up to
two channels is available.
b RCP/CNU connector (round 8-pin)
Used to connect to an MSU-1000 series Master Setup Unit,
CNU-700 Camera Command Network Unit, or RCP-3000/
1000 series Remote Control Panel via a CCA-5 Connection
Cable. Control signals are sent and received via this
connector. When using an RCP-3000/1000 series unit, power
is also supplied.
c 3G/HD SDI OUTPUT (SDI output) connector (SLOT1)
(BNC-type)
Used to output video signals from the video camera using
Multi-Link format comprising 3G-SDI signals or HD-SDI
signals.
For details about assignments to each signal output connector
in the Multi-Link interface, see "Relationship between
Connection Type and BNC Connector Assignment" (page 17).
d
(LAN-COM) connector (RJ-45 8-pin)
Used to connect to a LAN. Connect a LAN HUB (10BASE-T/
100BASE-TX), using a LAN cable (shielded type of category 5
or more).
e AUDIO OUT CH1, CH2 (audio output 1, 2) connectors
(XLR 3-pin)
Used to output the audio signal to the AUDIO IN connectors of
the video camera.
f CAMERA connector (optical fiber connector)
Used to connect a video camera, using an optical fiber cable.
All video camera signals, including power supply, control,
video, and audio, are sent and received over one optical fiber
cable.
Notes
• Dust on the connection surface of the optical fiber cable may
result in transmission errors. When not connected, always
cover the end of the connector with the supplied cap.
2 3
8 9 0
4 5 6
qa qs qd qf
• To connect to the HDC-P43, an HKCU-SM100 CCU
Extension Adapter and a single-mode fiber cable are
required.
g INTERCOM/TALLY/PGM (intercom/tally/program
audio) connector (D-sub 25-pin)
Used to input and output intercom, tally, and program audio
signals. Connect to the intercom/tally/program audio
connector of the intercom system.
REAR PREVIEW function: Pin 10 is assigned for the output
pin of the REAR PREVIEW function.
h RETURN SDI IN 1/2 (3G/HD/SD-SDI return video 1/2)
connectors (BNC-type)
Two different 3G/HD/SD-SDI return video input signals may
be received independently. The selection of RET 1 or 2 is
made by the return switch of the video camera. The aspect
ratio can also be selected for an SD signal.
The type of input signal on RET 1 and 2 may be set individually
using the setup menu, or using the MSU-1000 series Master
Setup Unit.
For details on the setup menu, contact a Sony service or sales
representative.
Refer also to the Master Setup Unit manual.
i 3G/HD SDI I/O 1/2 (SDI input/output 1/2) connectors
(SLOT3) (BNC-type)
These can be used as return video inputs, HD prompter
inputs, camera video signal outputs, and HD-TRUNK outputs.
Set them in SLOT3 on the <I/F SETTINGS> page of the
MAINTENANCE menu according to the application.
j INPUT area
1 PROMPTER 1, 2 (tele-prompter input) connectors
(BNC-type)
Input the prompter signal of 1 channel or 2 channels
depending on the setting of PROMPTER CHANNEL MODE
on the <TRUNK/PROMPTER1> page of the MAINTENANCE
menu. When 1 channel is set, the input signal is output from
9
qg