Pre-Installation; System Preparation; Artificially Softened Water; Water Systems And Pipework - Worcester Greenstar 4000 Installation And Maintenance Instructions Manual

Pre-Installation

Basic weather compensation sensor
Outdoor weather sensor (to activate on-board simple Weather
Compensation).
Part number Description
7 716 192 764 Outdoor weather sensor
Table 8 Control accessories
The outdoor weather sensor is supplied with the Sense II. It is optional
with the Comfort+ II RF. Weather compensation is available with the
EasyControl without the need for a physical outdoor sensor, however, it
can improve control accuracy for installations in isolated micro-climates
or highly sheltered locations such as valleys.
4 Pre-Installation
NOTICE
Risk of damage to system or appliance!
Before installation
▶ All the following Pre-Installation sections must be read and
requirements met before starting appliance or flue installations.
4.1

System preparation

4.1.1

Artificially softened water

The heating system must not be filled with water which has been treated
using an ion exchange (salt based) water softener. Where these water
softeners are installed, a permanent untreated water supply should be
provided to maintain pressure in the heating system.
A bypass must be provided at the water softener to comply with
BS:14743. Where a permanent untreated supply cannot be provided,
the system must be initially filled using the bypass provided at the water
softener. Occasional topping up of the system with artificially softened
water is acceptable. Inhibitor must be added to the system. The pH levels
must be between 6.5 and 8.0 at the time of commissioning. When a
permanent untreated supply is not provided to the heating system filling
point, the pH levels must be checked annually and recorded in the
service record.
NOTICE
Risk of damage to appliance!
▶ The heating system must not be filled with water which has been
treated using an ion exchange water softener.
▶ If the system is partially drained for maintenance or repair work, the
system must be refilled by utilising the bypass valve at the water
softener. The pH and inhibitor levels should be checked.
12
4.1.2

Water systems and pipework

Primary system plastic pipework:
• Any plastic pipework must have a polymeric barrier, complying with
BS 7921 and installed to BS 5955 with 600mm (minimum) length of
copper connected to the appliance.
• Plastic pipework used for under-floor heating must be correctly
controlled with a thermostatic blending valve limiting the
temperature of the circuits to approximately 50°C with 1000mm
(minimum) length of copper or steel pipe connected to the
appliance.
Primary system/connections/valves:
• Do not use galvanised pipes or radiators.
• All system connections, taps and mixing valves must be capable of
sustaining a pressure of 3 bar.
• Radiator valves should conform to BS 2767:10.
• All other valves should conform to BS 1010.
• It is best practice to fit Thermostatic Radiator Valves (TRV's) to all
radiators, except the area where the room thermostat is sited which
must be fitted with lockshield valves that are left open.
• If the circulating pump speed is fixed and system circulation can be
significantly adjusted or stopped by TRV's or zone valves, a system
bypass should be installed to give at least a 3 metre circuit when
activated. However; any appliance fitted with a modulating pump
may not require a system bypass.
• Drain cocks are required at all the lowest points on the system.
• Air vents are required at all high points on the system.
Showers/Bidets:
• If a shower head can be immersed in water or comes closer than
25mm from the top edge of a bath or shower tray spill-over level then
an anti-siphon device must be fitted to the shower hose.
• Bidets with direct hot and cold mains water can be used (with the
approval of the local water authority) and must be the over rim
flushing type with shrouded outlets to prevent the fitting of hand held
sprays.
Hot water:
• Taps and mixing valves must be capable of sustaining a pressure up to
10 bar.
• Hot water temperature and flow rate are affected by the size and
insulation of pipework making up the distribution system and are
controlled by the hot water tap and the water main inlet pressure. A
mixing valve can be fitted if a more permanent temperature setting is
required.
• If using more than one outlet at once causes water flow starvation, fit
flow balancing valves or Ball-O-Fix valves to the appropriate outlets.
• Thermostatic mixing valves (TMVs) must be fitted at the point of use
as specified in G3 of the building regulations and if specific, accurate
temperature control is required by the user.
Greenstar 4000 – 6 720 891 161 (2020/09)