Operation - Campbell Hausfeld FP2048 Operating Instructions And Parts Manual

Compresores Sin Aceite
Guía de diagnóstico de averías (Continuación)
Problema Posible(s) Causa(s)
Exceso de humedad en 1. Demasiada agua en el tanque
el aire de descarga
2. Humedad elevada
El compresor funciona 1. Presostato defectuoso
en forma continua y la 2. Válvula de seguridad defectuosa
válvula de seguridad se
abre cuando aumenta
la presión
Arranques y paradas 1. Demasiada condensación en el
excesivas tanque
2. Conexiones flojas (accesorios, tubería,
etc.)
Acción a tomar
1. Drene el tanque, incline el tanque para eliminar la
humedad
2. Llévelo a un área menos húmeda, utilice un filtro de
aire de línea
Nota: La condensación de agua no es una causa para
el malfuncionamiento del compresor.
1. Cambie el interruptor de presión
2. Cambie la válvula de retención con un repuesto
original
1. Drene con más frecuencia
2. Revise todas las conexiones con una solución de agua
y jabón. Si se detecta una fuga, apriete. O quite la
conexión y aplique cinta para tuberías a las rocas y
vuelva a armar.
22 Sp
Installation
(Continued)
DANGER
!
Do not use a
grounding adapter with this product!
2. If repair or replacement of cord or plug
is necessary, do not connect grounding
wire to either flat blade terminal. The
wire with insulation having an external
surface that is green (with or without
yellow stripes) is the grounding wire.
Never connect
WARNING
!
green (or green and
yellow) wire to a live terminal.
3. Check with a qualified electrician or
serviceman if grounding instructions
are not completely understood, or if in
doubt as to whether product is
Figure 2 - Unit Identification
properly grounded. Do not modify
plug provided; if it will not fit outlet, LUBRICATION
have proper outlet installed by a
This is an oilless product and DOES
qualified electrician.
NOT require lubrication to operate.
Overheating, short
CAUTION
!
BEFORE FIRST START-UP
circuiting and fire
damage will result from inadequate
BREAK-IN PROCEDURE
wiring, etc.
(Complete this procedure before using
compressor for the first time. Once

Operation

completed, it is not necessary to
repeat.)
Definition of Terms
1. Turn regulator knob fully clockwise
Regulator - The regulator controls the
(to the right) to open air flow.
amount of air pressure released at the
hose outlet.
2. Turn on/off switch to OFF position.
ASME Safety Valve - This valve
automatically releases air if the tank 3. Plug in power cord.
pressure exceeds the preset maximum.
4. Turn on/off switch to ON position
Handle - Designed to move the
and run compressor for 5 minutes.
compressor.
Drain Valve - This valve is located on 5. Turn on/off switch to OFF position.
the bottom of the tank. Use this valve
6. Unplug power cord.
to drain moisture from the tank daily
to reduce the risk of corrosion.
The compressor is now ready for use.
Reduce tank pressure below 10 psi,
then drain moisture from tank daily to
BEFORE EACH START-UP
avoid tank corrosion. Drain moisture
from tank by opening the drain valve
located underneath the tank.
Extension cords for 120V/2.5 Amp Unit
Length of Cord (ft) 25 50 100
Gauge of Cord 18 18 16
FP2048, FP2049
ON/OFF Switch
Handle
Regulator
Safety Valve
Drain Valve
OPERATING PROCEDURE
1. Turn regulator knob fully
counterclockwise (to the left) to close
air flow.
2. Connect air hose to outlet of
regulator.
3. Turn on/off switch to OFF position.
4. Plug in power cord.
5. Turn on/off switch to ON position
and let compressor run until it
reaches automatic shutoff pressure.
6. Attach tire chuck or tool to end of
hose.
7. Turn regulator knob clockwise (to
the right) to desired pressure of tool
being used.
On/Off cycling of compressor
In the ON position, the compressor
pumps air into the tank. When a shut-
off (preset "cut-out") pressure is
reached, the compressor automatically
shuts off.
150 200 250 300 400
14 14 12 12 10
www.chpower.com
3
500
10