Electrical Data; Operation; Wall Mounting - Campbell Hausfeld FP2032 Operating Instructions

Electrical Data

3. To avoid loss of power and
overheating, it is better to use
additional air hose instead of
extension cords to reach work area.
4. Table below shows correct size to
use depending on cord length and
nameplate ampere rating. If in
doubt, use next heavier gauge.
A
NOTE: The smaller the gauge number,
the heavier the cord.
5. This product is for use on a nominal
120 volt circuit and has a polarized
plug. Make sure that the product is
connected to an outlet having the
same configuration as the plug.
O,
DANGER
a !
GROUNDING INSTRUCTIONS
as
NOTICE
overheating, use additional air hose
instead of extension cords to reach
work area.
1. This product should be grounded. In
the event of an electrical short
circuit, grounding reduces risk of
b
electrical shock by providing an
escape wire for electric current. This
product is equipped with a cord
having a grounding wire with an
appropriate grounding plug. Plug
must be plugged into an outlet that
is properly installed and grounded
da
in accordance with all local codes
and ordinances.
DANGER
!
result in a possible risk of electrical shock!
NOTE: Do not use grounding adapter.
2. If repair or replacement of cord or
plug is necessary, do not connect
grounding wire to either flat blade
terminal. The wire with insulation
having an outlet surface that is green
with or without yellow stripes is the
grounding wire.
ou
Figure 2 - Grounding Method
de
s
Length of Cord (ft)
Gauge of Cord
All manuals and user guides at all-guides.com
(Cont.)
Do not use an adapter
with this product!
To avoid loss of
power and possible
Improper use of
grounding plug can
Grounded
Outlet
Grounding
TEST RESET
Pin
25 50
18 18
Model FP2030, FP2031, FP2032, FP2033
MOISTURE IN COMPRESSED AIR
Moisture in compressed air will form into droplets as it comes from an air
compressor pump. When humidity is high or when a compressor is in continuous
use for an extended period of time, this moisture will collect in the fittings and
hose. When using a paint spray or sandblast gun, this water will be carried from
the tank through the hose, and out of the gun as droplets mixed with the spray
material.
IMPORTANT: This condensation will cause water spots in a paint job,
especially when spraying other than water based paints. If sandblasting, it will
cause the sand to cake and clog the gun, rendering it ineffective. A filter in
the air line (MP3105), located as near to the gun as possible, will help
eliminate this moisture.
3. Check with a qualified electrician or
serviceman if grounding instructions
are not completely understood, or if in
doubt as to whether product is
properly grounded. Do not modify
plug provided; if it will not fit outlet,
have proper outlet installed by a
qualified electrician.
Never connect
WARNING
!
green (or green and
yellow) wire to a live terminal.

Operation

BREAK-IN PROCEDURE
Do not attach air
CAUTION
!
chuck or other tool
to open end of hose until start-up has
been completed and unit checks OK.
IMPORTANT: Do not operate
compressor before reading instructions
or damage may result.
1. With power switch OFF (O), turn
regulator knob fully
counterclockwise to minimum
operating pressure.
2. While unit is still OFF (O), plug in
power cord.
3. Turn switch to ON (I) position and
run unit for 5 minutes to break in the
pump parts.
This unit is a
NOTICE
continuously
running compressor. Normal operation
causes the regulator to vent air.
4. Attach chuck or other tool to open
end of hose. The compressor is now
ready to use.
Extension cords for 120V/5 Amp Unit
100 150 200
14 12 12
3
The switch should
CAUTION
!
be in the OFF (O)
position when connecting or
disconnecting the power cord from the
electrical outlet.
REGULATOR
1. This regulator controls air pressure to
the hose and attachment.
2. Turning knob clockwise increases air
pressure at outlet.
3. Turning counterclockwise will lower
air pressure at outlet.

Wall Mounting

This compressor is designed with an
option to be hung on a wall or
pegboard for convenient storage. It can
also be operated while in the hanging
position if one of the following
conditions is met:
1. If mounted on a wall, mounting
hardware is secured into wood or
masonry with suitable fasteners.
2. If mounted on drywall or gypsum
board, toggle bolts or mounting
anchors are strong enough and are
properly secure to resist vibration
from the compressor.
3. If mounted on a pegboard, other
items hung from the pegboard are
secure enough to resist vibration
from the compressor.
250 300 400
10 10 8
www.chpower.com
500
8