Operation - Campbell Hausfeld WF2050 Operating Instructions & Parts Manual

Operating Instructions and Parts Manual
Guide tube
Spindle
Welding wire
Tensioner ring
Tension spring
Tensioner knob
Retainer
Figure 2 - Weld Wire Routing
HANDSHIELD
Nozzle
Torch 1. Cut detachable handle (WF2050,
Contact Tip
Diffuser
WF2054 & WF2058 only; WF2057 is
supplied with a fully assembled
helmet) away from shield. Trim the
excess plastic to remove sharp edges
(See Figure 4).
Figure 3 - Torch Nozzle
Contact Tip Markings
Mark Wire Size
0.8 mm 0.030"
0.9 mm 0.035"
Assembly (Continued)
DUTY CYCLE / THERMOSTATIC
Figure 4
PROTECTION
2. To attach the handle, place shield on
Welder duty cycle is the percentage of
a flat surface and press handle into
actual weld time that can occur in a ten
place (See Figure 4).
minute interval. For example, at a 20%
duty cycle, actual welding can occur for
two minutes, then the welder must cool
for eight minutes.
Internal components of this welder are
protected from overheating with an
automatic thermal switch. A yellow
lamp is illuminated on the front
panel if the duty cycle is exceeded.
Welding operations may continue when
the yellow lamp is no longer illuminated.
Figure 5
POLARITY
3. Insert filter lens exactly as shown in
This welder is configured for DCEN, direct
Figure 5.
current electrode negative.
NOTE: If you have never welded before
or have little experience, a full face
www.chpower.com
helmet is recommended. Both hands
are needed to stabilize and control the
angle and arc length of the electrode.
Tensioner arm

Operation

1. Be sure to read, understand, and
Drive deck
comply with all precautions in the
Drive
General Safety Information section.
roller
Be sure to read the entire section
entitled Welding Guidelines prior to
using this equipment.
2. Turn welder off.
3. Verify that the surfaces of metals to
be joined are free from dirt, rust,
paint, oil, scale or other
Roller
contaminants. These contaminants
support
make welding difficult and cause
poor welds.
WARNING
!
equipment or in the area while
equipment is in use must wear
protective welding gear including: eye
protection with proper shade, flame
resistant clothing, leather welding
gloves, and full foot protection.
WARNING
!
materials that are galvanized, zinc
plated, lead, or cadmium plated refer to
the General Safety Information Section
for instructions. Extremely toxic fumes
are created when these metals are
heated.
4. Connect the work clamp to the work
piece or workbench (if metal). Make
sure the contact is secure. Avoid
surfaces with paint, varnish,
corrosion, or non-metallic materials.
5. Position the Heat Selector on the
front panel to the desired setting
(See decal inside wire feed
compartment).
Metal
Thickness
14 - 18 Gauge
Thicker Than 14 Gauge
NOTE: These settings are general
guidelines only. Heat setting may vary
according to welding conditions and
materials.
6. Rotate the Wire Speed Control to
setting number 5 to start with, then
adjust as needed after test weld.
7. Plug the input cord into a proper
voltage receptacle with proper
circuit capacity (See circuit
requirements on front page).
4
All persons
operating this
If heating,
welding, or cutting
Figure 12 - Modèlos WF2050, WF2054,
No. de Ref. Descripción
1
2
3
4
5
Heat 6
7
Setting
8
Low
9
10
High
L
11
L
12
L
13
L
14
L
15
L
L
16
L
17
L No se muestran
† Accesorio opcional
Modelos WF2050, WF2054, WF2057 & WF2058
6
10
8
WF2057 & WF2058
7
Ensamble de soplete y manguera (fundente revestido, 2,44 m, WF2050 & WF2057)
Ensamble de soplete y manguera (fundente revestido, 3,05 m, WF2054 & WF2058)
Punta de contacto - 0,035" (0,9 mm, 3,05 m, WF2054 & WF2058)
Punta de contacto opcional – 0,030" (0,8 mm) Paquete de 4
Punta de contacto opcional – 0,035" (0,9 mm) Paquete de 4
Boquilla
Portabobinas
Ensamble de la placa de conducción
Vástago y rejilla
Retén de la bobina
Resorte del retén de la bobina
Anillo del retén de la bobina
Alambre de soldar c/fundente – 0,030" (0,8 mm) Bobina de 2 lb (0,9 kg) (E71T-GS)
Alambre de soldar c/fundente – 0,030" (0,8 mm) Bobina de 10 lb. (4,54 kg) (E71T-GS)
Alambre de soldar c/fundente – 0,035" (0,9 mm) Bobina de 2 lb. (0,9 kg) (E71T-GS)
Alambre de soldar c/fundente – 0,035" (0,9 mm) Bobina de 10 lb. (4,54 kg) (E71T-GS)
Máscara de mano (no se incluyen lentes) (WF2050 & WF2058)
Lentes oscuros (para máscara de mano) (WF2050, WF2054 & WF2058)
Martillo/cepillo cincelador
Etiqueta adhesiva de seguridad
Pinza de tierra (WF2050)
Pinza de tierra (WF2054, WF2057 & WF2058)
Guantes para soldar (sólo WF2054, WF2057 & WF2058)
Casco de soldar (sólo WF2057)
37 Sp
1
2
5
3
4
9
No. del repuesto Ctd.
WC403650AV 1
WC404000AV 1
WT501400AV 1
WT501300AJ †
WT501400AJ †
WT502100AV 1
WC500805AV 1
WC500800AJ 1
WC707018AV 1
WC707024AV 1
WC707026AV 1
WC707023AV 1
WE200001AV †
WE201000AV †
WE200501AV †
WE201500AV †
WC801700AV 1
WC801100AV 1
WC803400AV 1
DK688509AV 1
WC100300AV 1
WC100600AV 1
WT200501AV 1
WT100500AV 1