Spraying Precautions; Installation - Campbell Hausfeld FP2051 Operating Instructions And Parts Manual

Portable Air Compressor
General Safety
DANGER
!
Information
(Continued)
Never attempt to repair
or modify a tank!
3. Only persons well acquainted with
Welding, drilling or any
these rules of safe operation should
other modification will weaken the
be allowed to use the compressor.
tank resulting in damage from rupture
4. Keep visitors away and NEVER allow or explosion. Always replace worn or
damaged tanks.
children in the work area.
5. Wear safety glasses
WARNING
and use hearing
!
protection when
13. Tanks rust from moisture build-up,
operating the pump
which weakens the tank. Make sure
or unit.
to drain tank daily and inspect
6. Do not stand on or use the pump or
periodically for unsafe conditions
unit as a handhold.
such as rust formation and
7. Before each use, inspect compressed
corrosion.
air system and electrical components
14. Fast moving air will stir up dust and
for signs of damage, deterioration,
debris which may be harmful. Release
weakness or leakage. Repair or
air slowly when draining moisture or
replace defective items before using.
depressurizing the compressor system.
8. Check all fasteners at frequent
intervals for proper tightness.

SPRAYING PRECAUTIONS

WARNING
!
WARNING
!
Motors, electrical
Do not spray flammable
equipment and controls
materials in vicinity of
can cause electrical arcs
open flame or near
that will ignite a flammable gas or
ignition sources including the
vapor. Never operate or repair in or
compressor unit.
near a flammable gas or vapor. Never
store flammable liquids or gases in the 15. Do not smoke when spraying paint,
vicinity of the compressor.
insecticides, or other flammable
substances.
CAUTION
!
16. Use a face mask/
Compressor parts may
respirator when
be hot even if the unit
spraying and spray in
is stopped.
a well ventilated area
to prevent health and
9. Keep fingers away from a running
fire hazards.
compressor; fast moving and hot
17. Do not direct paint or other sprayed
parts will cause injury and/or burns.
material at the compressor. Locate
10. If the equipment should start to
compressor as far away from the
abnormally vibrate, STOP the
spraying area as possible to
engine/motor and check
minimize overspray accumulation
immediately for the cause. Vibration
on the compressor.
is generally a warning of trouble.
18. When spraying or cleaning with
11. To reduce fire hazard, keep
solvents or toxic chemicals, follow
engine/motor exterior free of oil,
the instructions provided by the
solvent, or excessive grease.
chemical manufacturer.
Never remove or
WARNING
!
attempt to adjust
safety valve. Keep safety valve free
from paint and other accumulations.
www.chpower.com

Installation

LOCATION
It is extremely important to use the
compressor in a clean, well ventilated
area where the surrounding air
temperature will not be more than 100°F.
A minimum clearance of 18 inches
between the compressor and a wall is
Drain liquid from
required because objects could obstruct
tank daily.
air flow.
Do not locate the
CAUTION
!
compressor air
inlet near steam, paint spray, sandblast
areas or any other source of
contamination. This debris will damage
the motor.
GROUNDING INSTRUCTIONS
1. This product is for use on a nominal
120 volt circuit and has a grounding
plug that looks like the plug illustrated
in Fig. 1. Make sure the product is
connected to an outlet having the
same configuration as the plug. This
product must be grounded. In the
event of an electrical short circuit,
grounding reduces risk of electrical
shock by providing an escape wire for
electric current. This product is
equipped with a cord having a
grounding wire with an appropriate
grounding plug. Plug must be plugged
into an outlet that is properly installed
and grounded in accordance with all
local codes and ordinances.
Grounding
Pin
TEST RESET
Grounded Outlet
Figure 1 - Grounding Method
DANGER
!
Improper use of
grounding plug can
result in a possible risk
of electrical shock!
2
Lista de Repuestos
No. de Número del
Ref. Descripción repuesto
1 Cabezal/motor FP205110AV
I
2 Patas del chasis
L
3 Patas de la cubierta del motor
4 Cubierta izquierda del compresor FP205111AV
5 Cubierta derecha del compresor FP205112AV
6 Panel del manómetro FP205113AV
7 Chasis FP205114AV
8 Mango FP205115AV
9 Distribuidor (incluye regulador) FP205116AV
10 Bandeja de accesorios FP205117AV
N
11 Tubo de escape
G
12 Soporte de montaje para pared
I
13 Tornillo 1/4x19
I
14 Tornillo M6x15
M
M
15 Tornillo M6x200
16 Presostato FP205118AV
J
17 Tablero del circuito
18 Cordón eléctrico ∆
N
19 Conexión de compresión
N
20 Tuerca de compresión
N
21 Manga
22 Arandela de 6,4 mm (1/4")
I
(No se muestra)
M
23 Interruptor de encendido/apagado FP205129AV
24 Válvula de drenaje D-1403
25 Accesorios de inflado
26 Adaptador
27 Boquilla para neumático
Tuerca de retención de la cubierta M
28
M
29 Tornillo 3x8
Tornillo de fijación para hormigón G
30
31 Valvula de chequeo †
32 Resorte †
33 Manómetro de salida FP006300AV
34 Manómetro del tanque GA016304AV
H
35 Tornillo M3x10
FP2051, FP2052
FP2051, FP2052
No. de Número del
Ctd. Ref. Descripción repuesto
H
1 36 Tuerca M3x2,5
H
4 37 Arandela
H
4 38 Ventilador
39 Alivio de tensión
1 ∆
1 40 Tornillo M4x8 ∆
J
1 41 Tornillo M3x10
J
1 42 Sujetador del cableado
43 Valvula de seguridad V-215105AV
1
#
1 44 Gancho de la correa
#
1 45 Correa
#
46 Tornillo M4x10
1
47 Fusible FP205130AV
1
L
4 48 Tornillo autorroscante
L
4 49 Tubo de goma
L
50 Tornillo
4
L
51 Tuerca
1
L
1 52 Placa fija del motor
L
1 53 Tuerca
G
54 Tornillo para madera
1
JUEGOS DE REPUESTOS
2
L
2 Juego de montaje del motor FP205131AV
I
2 Juego de las patas del chasis FP205120AV
G
Juego de montaje para pared FP205121AV
N
4 Juego de tubos FP205122AV
M
4 Juego de tornillos de la cubierta FP205123AV
J
1 Juego del tablero de circuitos FP205124AV
Juego del cordón de corriente FP205125AV
1 ∆
1 † Juego de la válvula de chequeo FP205126AV
H
1 Juego del ventilador FP205127AV
#
1 Juego de la correa FP205128AV
Kit de herramienta FP204008AV
1
5 Juego para calcomanía (No se muestra)
3 Modelo FP2051 FP205132AV
1 Modelo FP2052 FP205221AV
1
1
1
2
27 Sp
Ctd.
2
2
1
1
2
2
1
1
1
1
1
1
1
2
1
4
1
1
3