Sony HDCU1700 Operation Manual page 8

• DISP/MENU (display/menu) lever and indicator
Selects the status display or setup menu display. In setup
menu mode, the indicator turns on.
• CANCEL/ENTER lever
In setup menu mode, used to cancel and enter settings.
• CONTROL knob (rotary encoder)
In status screen mode, used to change the displayed page. In
setup menu mode, used to move the cursor on a page and to
change menu settings. Pressing the CONTROL knob
performs the same function as setting the CANCEL/ENTER
lever to the ENTER position.
g CABLE ALARM indicators
OPEN (red): Lights in red when a camera isn't connected to
the CAMERA connector on the rear panel of this unit via
an optical fiber cable. Flashes when the connection
status of an optical fiber cable is bad.
SHORT (red): Lights in red when the power supply cord of an
optical fiber cable is short to external, or two power
supply cords are short. Power isn't input to the camera
when this indicator lights.
h POWER switch and indicators
Turns the entire system on and off, including this unit, the
video camera, and the RCP-1000 series Remote Control
Panel connected to the REMOTE connector of this unit. The
MAIN indicator and the CAM indicator light when the power
switch is turned on. Pressing the CAM PW button of the
master setup unit and the remote control panel turns off the
video camera only, and only the CAM indicator turns off.
Note
In order for the power supply to supply the unit with the
necessary power to start up, energy is consumed even when
this switch is set to OFF.
i INTERCOM audio input/output and control block
MIC/PGM (microphone/program) switch
INTERCOM (intercom select) switch
INTERCOM (intercom adjustment) knob
INTERCOM connector (XLR 5-pin)
• MIC/PGM (microphone/program) switch
ON: Turns the headset microphone on.
OFF: Turns the headset microphone off.
PGM: Selects program audio output. In this mode, the
INTERCOM knob adjusts the headset program audio
level.
• INTERCOM (intercom select) switch
Selects the intercom signal input/output connection source for
the INTERCOM connector on the front panel.
PROD: Connects the producer line.
PRIV: Blocks the connection to the producer line or engineer
line, allowing private intercom talk between the CCU and
the camera.
ENG: Connects the engineer line.
• PRIV (Private) indicator
Lights when the intercom is in private mode.
• INTERCOM (intercom adjustment) knob
Adjusts the receiver audio level of the intercom.
• INTERCOM connector (XLR 5-pin)
Connects the intercom headset.
To use a headset with a plug other than an XLR 5-pin plug,
consult a Sony service or sales representative.
j Network indicator
Displays the network system connection status.
On: When CNS SETTING in the NETWORK SETTING menu
is set to either BRIDGE or MCS, this indicates that
external control equipment (MSU-1000/1500 Master
Setup Unit, RCP-1000-series Remote Control Panel, or
other device) is connected.
Flashing: When CNS SETTING in the NETWORK SETTING
menu is set to either BRIDGE or MCS, this indicates a
connection problem with the external control equipment
(MSU-1000/1500 Master Setup Unit, RCP-1000-series
Remote Control Panel, or other device).
Off: When CNS SETTING in the NETWORK SETTING menu
is set to either BRIDGE or MCS, this indicates that a LAN
cable is not connected or that the network system
connection parameters have not been set.
When the CNS SETTING in the NETWORK SETTING
menu is set to LEGACY, this remains turned off.
k Call button
When pressed, this outputs a call signal to the camera and
external control device (the RCP-1000 series, etc.) that are
connected to this unit. Use this when you want to call and
speak with the camera operator or external control device
operator via intercom.
l Menu lock switch
This locks out operation of the front panel menu operation
area.
m Assignable button
You can set a function for this button via the CCU menu.
n Status display indicator
REF IN (Green): REFERENCE is being input.
UNLOCK (Red): The input REFERENCE is not locked.
COM ERROR (Red): There is a communication failure with
the camera or other external control equipment (such as
the RCP-1000 series Remote Control Panel).
FAN STOP (Red): The power fan is stopped.
8