Table of Contents
Advertisement
Quick Links
H
C
EALTH ARE
Imaging
>
Order-No.: DD+DIS160.02E
*1VC2SN1*
1 Piece VC2SN MA1
printed in Germany 06 / 2002
Installation Manual for ADC Easylift
(Type 4406/027)
Read carefully before starting installation!
ADC Easylift and ADC Cassette holder must only be installed, opened,
repaired and removed by a qualified service engineer!
Necessary time for installation:
approx. 1.5 h
Necessary tools:
•
flat nose pliers
•
wire cutting pliers
•
2mm allen key
•
3mm allen key
•
4mm allen key
•
5mm allen key
•
6mm allen key
•
5mm socket wrench
•
8mm socket wrench
•
10mm offset box wrench or ratchet
HOME
ADC System Components
Accessories
Type 4406
Advertisement
Table of Contents
Related Manuals for AGFA 4406/027
Summary of Contents for AGFA 4406/027
- Page 1 *1VC2SN1* Type 4406 1 Piece VC2SN MA1 Installation Manual for ADC Easylift (Type 4406/027) Read carefully before starting installation! ADC Easylift and ADC Cassette holder must only be installed, opened, repaired and removed by a qualified service engineer! Necessary time for installation: approx.
-
Page 2: Table Of Contents
HOME Accessories DD+DIS160.02E List of contents Safety Instructions for ADC Easylift ....... 3 Certificates..............4 Scope of Delivery ............. 5 Installation Planning..........5 Installation Site................ 5 Fixation Requirements............6 Technical Data ................. 7 Unpacking ADC Easylift........... 8 Installation Instructions ........... 8 Finishing the Installation ........ -
Page 3: Safety Instructions For Adc Easylift
Read these safety instructions cautiously, before doing any installation or repair work on the ADC Easylift Safety instructions relevant for the user The 'Intended Use' is lifting up and lowering down the attached Agfa cassette holder. Safety precautions Cassette holder is only to be removed by a qualified service engineer. -
Page 4: Certificates
HOME Accessories DD+DIS160.02E Safety instructions relevant for the field service engineer See "Safety instructions relevant for the user" and additionally: Wall attachment : Always make sure that the hospital points out the methods and location of the wall attachment. This because the hospital responsible knows best where the utilities (water, electricity, medical gasses, etc,...) are located. -
Page 5: Scope Of Delivery
HOME DD+DIS160.02E Accessories Scope of Delivery The Full Leg/Full Spine Stand "ADC Easylift" consists of the following assemblies: • Framework with Sprocket Holder • Counterweight • Slide wagon • Upper front cover • Lower front cover and the following single parts packed in small PE-bags: •... -
Page 6: Fixation Requirements
HOME Accessories DD+DIS160.02E Fixation Requirements The preparation of the wall fastening has to be done by the customer. They have to take into account the material of the wall as well as the fixing material. At the time of installation the preparation of the wall fastening must be finished and the required fixation bolts must be on the spot. -
Page 7: Technical Data
HOME DD+DIS160.02E Accessories Technical Data Dimensions and Weights Packing dimensions 2375 mm x 595 mm x 385 mm (length x width x depth) Dimensions ADC 2300 mm x 390 mm x 135 mm Easylift mounted (length x width x depth) Dimensions slide- 1300 mm x 390 mm wagon... -
Page 8: Unpacking Adc Easylift
HOME Accessories DD+DIS160.02E Unpacking ADC Easylift Wear safety shoes and gloves while unpacking and installing ADC Easylift. (1) Cut the fixing straps. (risk of injury) and lift off the wooden lid. (2) Lift Easylift off the case and unwrap it. (3) Put it on firm ground for further installation steps... - Page 9 HOME DD+DIS160.02E Accessories (4) Loosen 3 screws at each side of the 3mm allen key upper front cover (1) (5) Draw off the lower front cover while lifting it a bit (3) Do not bend Figure 4 (6) Unpack and check the accessory kit according to the assembly checklist...
- Page 10 HOME Accessories DD+DIS160.02E (8) Fasten 2 adjustable feet with 2 screws 5mm allen key each Figure 6 (9) Loosen 4 nuts at the 10mm offset box wrench or ratchet counterweight bracket and remove bracket Figure 7 (10) Fasten handle with 4 allen screws 4mm allen key (11) Attach brake-...
- Page 11 HOME DD+DIS160.02E Accessories (12) Pull the brake- cable through the flat nose pliers, wire cutting pliers, 2mm allen key opening in the sprocket holder (13) Check the correct position of the cable sleeve (14) Fasten the brake- cable with 2 cone pointed allen screws (15) Cut off the...
- Page 12 HOME Accessories DD+DIS160.02E (18) Put up the Easylift and attach it with 4 bolts to the wall. Use the bolts provided by the customer. 4406_dis01802_013.CDR Figure 12 Risk of injury! For the following installation steps the belt locking system must be blocked 4406_dis01802_021.CDR Figure 13 Chapter 6 / 12...
- Page 13 HOME DD+DIS160.02E Accessories (19) Loosen 4 locking 8mm socket wrench screws securing the counterweight in the (20) Take the counterweight out of the box 30,5 kg ! Figure 14 (21) Secure slide wagon 10mm offset box wrench or ratchet in upper locking position (22) Put the counterweight inside...
- Page 14 HOME Accessories DD+DIS160.02E (24) Connect counterweight with 6mm allen key belt by belt mounting plate 4406_dis01802_014.CDR Figure 16 (25) Remove slide wagon locking screws (1) (26) Release belt locking system (2) (27) Move slide wagon downward (3), (you need a helping hand) 4406_dis01802_015.CDR Figure 17...
- Page 15 HOME DD+DIS160.02E Accessories (28) Mount upper front cover with 3 allen 3mm allen key screws each side 4406_dis01802_016.CDR Figure 18 Risk of injury! Block belt locking system again (see below 1) (29) Have your 3mm allen key assistance lift on the slide wagon as far as possible (2) (30) Mount lower front...
- Page 16 HOME Accessories DD+DIS160.02E (31) Mount the cassette holder mounting brackets at the cassette holder (1) (32) Attach the cassette holder to the slide wagon. Take care that the lugs have engaged properly. 4406_dis01802_018.CDR Figure 20 (33) Fasten the cassette 5mm socket wrench holder mounting brackets to the slide wagon (1)
-
Page 17: Finishing The Installation
HOME DD+DIS160.02E Accessories Finishing the Installation (1) Check the ADC Easylift for safe and proper function: • reliable locking of both locking systems of the device • smooth movement of slide wagon/cassette holder (2) Hand over the system to the customer.