Wolf Rangetop Service Manual

Wolf Rangetop Service Manual

Sealed burner rangetop with wo

Advertisement

Quick Links

General Information
GENERAL INFORMATION
SERVICE MANUAL INTRODUCTION
This service manual helps with troubleshooting and diagnosing
malfunctions, completion of repairs, and return of the product to
proper operating condition. Read the complete instructions
contained within before initiating any repairs.
This guide is intended for use by Factory Certified Service. Wolf
Appliance, Inc. recommends that only Factory Certified Service
companies do repairs.
Warning and Caution product safety labels appear throughout
this manual. Product safety labels appear at the beginning of
some sections. Follow the instructions in the product safety
labels to avoid personal injury and/or product damage. The
sample safety labels explain the types of notices that appear in
this manual.
WARNING
States a hazard that may cause serious injury or
death if precautions are not followed.
CAUTION
Indicates minor injury or product damage may occur
if precautions are not followed.
IMPORTANT NOTE: Highlights especially important information.
TIP: Indicates additional, useful information.
Information and images contained herein are copyright of Wolf
Appliance, Inc. Neither this manual nor any information or
images contained herein may be copied or used in whole or in
part without the express written consent of Wolf Appliance, Inc.
©
Wolf Appliance, Inc., all rights reserved.
SEALED BURNER RANGETOP PRODUCT RATING PLATE
INFORMATION
On Sealed Burner Rangetops, the product rating plate is on the
bottom of the bullnose assembly.
828990 REV. A
Sealed Burner Rangetop with Wok Service
Important information for each product appears on the product
rating plate. Rating plates identify:
Model
Serial number
Electrical information
Total heat input
Burner heat ratings (in Btu)
Type and pressure of gas
MODEL DESCRIPTIONS AND SALES ACCESSORIES
For more details on individual model descriptions and a listing
of all compatible sales accessories, see the
Price List
.
SEALED BURNER RANGETOPS MODEL KEY
Model Character
ICB
SRT
30, 36, or 48
4 or 6
G
DG
C
F
W
-LP
PRODUCT USE AND CARE AND INSTALLATION GUIDES
Product use and care guides, installation guides, and other
product specifications are available in the
Specifications and Manuals Library
1
Manual
service.subzero.com
Wolf Distributor
Description
International Designation
Sealed Burner Rangetop
Size (in Inches)
Number of Burners
Infrared Griddle
Infrared Dual Griddle
Infrared Charbroiler
French Top
Wok
Liquid Propane
Product
.

Advertisement

Table of Contents
loading

Summary of Contents for Wolf Rangetop

  • Page 1 ▪ contained within before initiating any repairs. ▪ Burner heat ratings (in Btu) This guide is intended for use by Factory Certified Service. Wolf Type and pressure of gas ▪ Appliance, Inc. recommends that only Factory Certified Service companies do repairs.
  • Page 2: General Information

    Sealed Burner Rangetop with Wok Service Manual General Information service.subzero.com Unit Warranty (continued) UNIT WARRANTY Product warranty is determined by the installation location and the date of installation. http://service.subzero.com/ ▪ View product warranties at ClaimsAndOrderProcessing/Pages/WarrantyInfo Warranties start on the day of product installation.
  • Page 3 Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com COMPONENT REMOVAL AND INSTALLATION Remove the Wok Grate FLAT WOK GRATE REMOVAL Lift the wok grate directly upward from the wok plate. WARNING The wok grate is very heavy. Two people may be Remove the Flat Wok Grate necessary to lift the wok grate.
  • Page 4 Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com Remove the Wok Top Plate (continued) Wok grate Remove the Wok Top Plate Wok top plate Lift the wok top plate directly upward from the wok support assembly.
  • Page 5 Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com REMOVE THE WOK ENCLOSURE (continued) Lift the wok enclosure directly upward from the wok frame. Lift the wok frame upward from the support rails in the burner box.
  • Page 6: Solenoid Installation

    Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com Remove the Wok Spacer Rail (continued) Remove the Wok Spacer Rail Remove the solenoid from the unit. Lift the wok spacer rail directly upward from the supports in the burner box.
  • Page 7: Component Removal And Installation

    Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com REMOVE THE WOK BURNER ASSEMBLY (continued) Remove the wok burner assembly from the unit. WOK SURFACE BURNER INSTALLATION Install the Wok Surface Burner Install the surface burner into the top of the gas burner.
  • Page 8 Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com Wok burner assembly Slide the electrode mount upward and away from the electrode. Remove the Wok Ignitor Use a " socket to remove the wok ignitor mounting screw.
  • Page 9: Bottom Panel Removal

    Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com REMOVE THE WOK TRAY (continued) Remove the wok tray from the unit. Remove the wok mounting bracket from the unit. WOK TRAY INSTALLATION WOK MOUNTING BRACKET INSTALLATION Install the Wok Tray Install the Wok Mounting Bracket Set the wok tray into the bottom of the wok enclosure.
  • Page 10 Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com REMOVE THE BOTTOM PANEL (continued) Remove the wok bottom panel from the unit. Remove the wok elbow from the unit. BOTTOM PANEL INSTALLATION WOK ELBOW INSTALLATION Install the Bottom Panel Install the Wok Elbow Place the bottom panel into the unit.
  • Page 11 Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com REMOVE THE WOK ORIFICE ASSEMBLY (continued) Remove the wok orifice assembly from the unit. Place the burner grates onto the unit. BURNER CAP REMOVAL To remove the burner cap, first remove:...
  • Page 12: Burner Assembly Removal

    Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com REMOVE THE ISLAND TRIM (continued) Pull the trim upward to remove it from the unit. Disconnect the electrode wire from the ignitor. Burner Cap Burner Assembly Ignitor Electrode Wire...
  • Page 13: Knob Installation

    Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com Burner Pan Installation (continued) BURNER PAN INSTALLATION Remove the bezel from the bullnose. Install the Burner Pan(s) Place the burner pan(s) onto the unit. KNOB REMOVAL Remove the Knob Pull the knob straight off of the shaft.
  • Page 14: Side Panel Installation

    Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com REMOVE THE BULLNOSE (continued) Use a T-15 Torx bit to remove the screws holding the Remove the Side Panel bullnose to the burner box supports. Use a Phillips screwdriver to remove the side panel Lift the bullnose off of the screws around the outside of the mounting screws.
  • Page 15: Manifold Installation

    Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com REMOVE THE BURNER BOX SUPPORT (continued) Remove the burner box support from the unit. Remove the manifold from the unit. BURNER BOX SUPPORT INSTALLATION MANIFOLD INSTALLATION Install the Burner Box Support...
  • Page 16 Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com REMOVE THE ORIFICE HOLDER (continued) Use a T-15 Torx bit to remove the screws holding the orifice Remove the orifice holder mounting bracket from the unit. holder to the sealed burner bracket.
  • Page 17: Spark Module Removal

    Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com DSI Board Cover Installation (continued) DSI BOARD COVER INSTALLATION Connect the DSI board wire connectors. Place the ground connection under the removed orifice holder's hat bracket. Install the Board Cover Use a T-15 Torx bit to install the screws holding the orifice Place the board cover into the unit.
  • Page 18 Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com INSTALL THE SPARK MODULE (continued) Connect the electrode wire to the spark module. Burner pan To remove the wiring cover for a 36" unit, first remove: Flat wok grate...
  • Page 19: Power Cord Installation

    Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com Wiring cover Burner pan To remove the regulator for a 36" unit, first remove: Flat wok grate Remove the Power Cord Wok grate Disconnect the wire leads at the quick disconnect.
  • Page 20 Sealed Burner Rangetop with Wok Service Manual Component Removal and Installation service.subzero.com INSTALL THE REGULATOR (continued) Use a combination wrench to install the regulator outlet line onto the regulator outlet. 828990 REV. A...
  • Page 21: Troubleshooting Guide

    Sealed Burner Rangetop with Wok Service Manual Troubleshooting Guide service.subzero.com TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE Problem Possible Cause Test/Action Test the polarity of the outlet. If the polarity is incorrect, consult an electrician. Reverse polarity on outlet or unit (all burners) Check the internal connections.
  • Page 22 Sealed Burner Rangetop with Wok Service Manual Troubleshooting Guide service.subzero.com Problem Possible Cause Test/Action Burner assembly damaged or dirty with food Replace or clean the burner assembly. debris Popping noise at burner Burner assembly cracked or warped Replace the burner assembly.
  • Page 23 Sealed Burner Rangetop with Wok Service Manual Troubleshooting Guide service.subzero.com WOK TROUBLESHOOTING Problem Possible Cause Test/Action Bad microswitch at burner valve Replace the microswitch. Constant sparking at wok ignitor Bad DSI board Replace the DSI board. Arcing from DSI board to cover or unit chassis Check for breaks in insulation.
  • Page 24 Sealed Burner Rangetop with Wok Service Manual Troubleshooting Guide service.subzero.com DSI Board Troubleshooting (continued) DSI BOARD TROUBLESHOOTING 828990 REV. A...
  • Page 25: Gas Pressure Testing

    Full load is when all gas appliances in the home are on including the rangetop. Disconnect the main gas tube from a 9.2K orifice holder, and connect the manometer to the main gas tube. Set the Supply line to the unit is not ".
  • Page 26 Sealed Burner Rangetop with Wok Service Manual Troubleshooting Guide service.subzero.com Install the Unit (continued) INSTALL THE UNIT Install the unit. 828990 REV. A...
  • Page 27: Technical Data

    Sealed Burner Rangetop with Wok Service Manual Technical Data service.subzero.com TECHNICAL DATA SRT WOK TECHNICAL DATA ELECTRICAL REQUIREMENTS Power Service 110/120 VAC, 60 Hz 15 amp dedicated circuit SOLENOID Parameter Value Resistance Approx. 208 Ω ORIFICE SIZES: NATURAL GAS Item...
  • Page 28: Wiring Diagrams

    Sealed Burner Rangetop with Wok Service Manual Wiring Diagrams service.subzero.com WIRING DIAGRAMS SRT WOK WIRING DIAGRAMS 828990 REV. A...
  • Page 29 Sealed Burner Rangetop with Wok Service Manual Wiring Diagrams service.subzero.com 828990 REV. A...

Table of Contents