Efficiencies - Hearth and Home Technologies OXDV30SP Installation And Operating Instructions Manual

Approved Vent System Components
The Stardance heater must be vented to the outdoors through
an adjacent exterior wall or through the roof. The venting
system must be comprised of the appropriate listed venting
components specified on this page. These parts are available
from DuraVent Corporation or your Vermont Castings Dealer.
See Figure 4 for dimensions relevant to the standard
minimum-vent kits.
HHT Components*
Free Standing Stove Kit w/adj.
Termination Cap, SLP24-BK, SLP6-BK,
SLP6A-BK, SLP90-BK, SLP-WT-BK &
CCSLP
Trapezoid Termination Kit (3-1/8" - 4-3/4")
Trapezoid Termination Kit (5-1/4" - 9-1/4")
Rear Vent Termination Kit
Vertical Termination cap – High Wind
(includes storm collar)
Decorative Wall Thimble Cover
Decorative ceiling firestop – black
Cathedral ceiling support – black
4" (100mm) pipe length – black
6" (150mm) pipe length – black
12" Pipe length-black
24" Pipe length-black
36" (915mm) pipe length – black
48" Pipe length-black
3" - 6" (75 – 150mm) telescoping pipe
extension – black
3" - 12" telescoping pipe extension-black
45 degree elbow-black
90 degree elbow-black
Freestanding Draft Hood Adapter
*CCSLP adapter is required when using HHT components.
38 Hearth and Home Technolgies • Oxford Direct Vent Installation Manual_R6 • 08/17
DuraVent Components
Minimum Horizontal Vent Kit
Starter Pipe Assembly (incl. inner & outer
sections)
90° Elbow, Blk.
45° Elbow, Gal.
6" Straight, Blk.
9" Straight, Blk.
11" – 14
12" Straight
24" Straight
SLP-FSSK
36" Straight
48" Straight
SLP-TRAP1
Horizontal Vent Cap
SLP-TRAP2
Wall Plate
SLP-RVTK
Vinyl Siding Shield
SLP-TVHW
Snorkel Termination – 14"
Snorkel Termination – 36"
SLP-WT-BK
Wall Strap
SLP-DCF-BK
Cathedral Ceiling Support Box
SLP-CCS-BK
Storm Collar
SLP4-BK
Firestop Spacer
SLP6-BK
Flashing 0/12 - 6/12
SLP12-BK
Flashing 6/12 - 12/12
SLP24-BK
Wall Thimble
SLP36-BK
Wall Thimble Cover (Brass)
SLP48-BK
Wall Firestop
SLP6A-BK
Attic Installation Shield
Co-Linear Vent Adapter
SLP12A-BK
Steel Chimney Conv. Kit A (6-5/8" - 8-5/8")
SLP45-BK
Steel Chimney Conv. Kit B (6-5/8" - 10-1/2")
SLP90-BK
Steel Chimney Conv. Kit C (6-5/8" – 13")
FSDHAGSLP
Masonry Chimney Conversion Kit
Vertical Termination Cap (High Wind)
Vertical Termination Cap (Low Profile)
*Included in Minimum Horizontal Vent Kit #2792
All DuraVent Straight vent pipe sections have a net length 1-1/2"
(37mm) less than the nominal dimension; i.e., a 6" (152 mm)
Straight pipe section has an effective length of 4-1/2" (115 mm).
⁄ " Adjustable Straight Section
5
8
2792
2768*
46DVA-E90B*
46DVA-E45
46DVA-06B*
46DVA-09B
46DVA-08AB
46DVA-12
46DVA-24B*
46DVA-36B
46DVA-48
46DVA-HC*
46DVA-DC
46DVA-VSS
46DVA-SNK14
46DVA-SNK30
46DVA-WS
46DVA-CS
46DVA-SC
46DVA-FS
46DVA-F6
46DVA-F12
46DVA-WT
3PVP-TKV
46DVA-WFS
46DVA-IS
46DVA-GCL
46DVA-KCA
46DVA-KCB
46DVA-KCC
46DVA-KMC
46DVA-VCH
46DVA-VC
3-90-693831