Full Facepiece Respirators (7000 Series Shown) - 3M SA-1500 User Instructions

Fig. 4
Fig. 6
1. Hold the half facepiece in front of you so that the 3M logo on the half facepiece is facing you. Align the two branches
of the breathing tube over the two bayonet mounts on the half facepiece. For the 3M™ Dual Airline Breathing Tubes
SA-1500 or SA-1600, make sure that the 3M logo on the breathing tube and on the half facepiece are both facing
towards you. For the 3M™ Dual Airline Breathing Tubes SA-2500 or SA-2600, make sure that the 3M logo on the
breathing tube is facing in the opposite direction to the 3M logo on the half facepieces (Figs. 2 and 3).
2. Twist each branch of the breathing tube clockwise a quarter turn until it is fi rmly seated in the bayonet and cannot be
turned further. Do not forcibly overturn as the bayonet could be damaged (Figs. 4 and 5).
3. Place the belt around the waist and adjust for size and comfort (Fig. 6).
4. Place the metal belt clip of the air regulator/connector on the belt (Fig. 7).
5. On the dual airline breathing tubes SA-1500 or SA-1600, use the clip to secure the tube to your clothing (Fig. 8).
Fig. 5
Fig. 7
Fig. 8
9
3M™ Full Facepiece Respirators (7000 Series Shown)
Fig. 9
SA-1500
Fig. 12
NOTE: If your 3M™ Full Facepiece 7800S is already equipped with 3M™ Bayonet Adapters 701, steps 1-3 may be omitted.
1. Remove the 3M™ Plugs 7890, if not already fi tted with 3M™ Bayonet Adapter 701 (Fig. 9).
2. The 3M™ Bayonet Adapter 701 allows you to attach the dual airline breathing tube to the 3M™ Full Facepiece 7800S
(Fig. 10).
3. Thread the assembled 3M™ Bayonet Adapter 701 into the cartridge connector port – do not tighten (the orange gasket
will be facing outward). Align the small solid bayonet lug to the bottom of the facepiece lens and tighten the nut. Place
another 3M™ Bayonet Adapter 701 in the opposite cartridge connector port following the same procedure (Fig. 11).
4. Align the two branches of the breathing tube over the bayonet mounts on the facepiece. For the 3M™ Dual Airline
Breathing Tubes SA-1500 or SA-1600, make sure that the 3M logo on the breathing tube and front of the facepiece are
both facing towards you. For the 3M™ Dual Airline Breathing Tubes SA-2500 or SA-2600, make sure that the 3M logo
on the breathing tube is facing in the opposite direction to the 3M logo on the front of the facepiece (Fig. 12).
Twist each branch of the breathing tube clockwise a quarter turn until it is fi rmly seated in the bayonet and cannot be
turned further. Do not forcibly overturn as the bayonet could be damaged (Figs. 13 and 14). 3M™ Dual Airline Back-
Mounted Breathing Tubes SA-2500/SA-2600. Full facepiece respirators with DIN connections only. Install 7890 plug in
center port (Fig. 15).
Assembly of 3M™ Combination Dual Airline Respirator with Cartridges and Filters
The SA-1600 (front-mounted) and SA-2600 (back-mounted) versions of the 3M™ Dual Airline Breathing Tubes allow the
use of selected, NIOSH-approved 3M™ Cartridges 6000 Series and 3M™ Particulate Filters 2000 Series. For the listing of
approved cartridges and fi lters, please reference the NIOSH approval label.
Fig. 16
Fig. 10
Fig. 13 Fig. 14
Fig. 17
10
Fig. 11
Fig. 15
Fig. 18