Using The Import/Export Function; Importing Tones; Importing Scenes - Roland Jupiter-Xm Reference Manual

Using the IMPORT/EXPORT function

Importing Tones

You can import tones that you've downloaded or exported from other
models into the JUPITER-Xm as additional tones.
* You can also import tones from models.
When you import a tone that does not belong to a model, the model name is
saved as "NO ASSIGN."
Saving tones to USB flash drive
1 .
Prepare a SVZ file with the tones you've downloaded or
exported from other models by using their export function,
which you'll import into the JUPITER-Xm .
2 .
Connect a USB flash drive to your computer .
* If this is the first time you're using the USB flash drive, format it on the
JUPITER-Xm.
&
"Formatting a USB Flash Drive (FORMAT USB MEMORY)"
3 .
Save the SVZ file to the
USB flash drive .
4 .
Remove the USB flash drive from your computer and
connect it to the JUPITER-Xm .
Importing tones into the JUPITER-Xm
1 .
Press the [MENU] button .
2 .
Use the [1] knob to select
[ENTER] button .
You can also make this selection by using the
instead of the [1] knobs.
3 .
Use knob [1] to select "IMPORT/EXPORT,"
[ENTER] button .
4 .
Use knob [1] to select "IMPORT TONE,"
[ENTER] button .
5 .
Use knob [1] to select the file containing the tone you wish
to import, and press the
The number of tones that are saved in that file are shown in
parentheses.
6 .
Use knob [1] to select the tone you wish to import, and use
knob [2] to select it with a check mark . To select or deselect
all tones, hold down the
[2] .
To select or deselect a certain range of tones, press the
at the beginning of the range, and then press
[SHIFT] button at the end of the range.
7 .
Press the PAGE [>] button .
8 .
Use knob [1] to select where to import the tone, and press
the [ENTER] button to select it with a check mark .
NOTE
5
Tones that are being used in a scene are marked with an asterisk (*).
5
Use caution, as this overwrites the tone you select that's already in the import
destination.
5
If there are not enough locations in the import destination to save the data to be
imported, not all of the tones selected are imported.
5
You can check the number of tones at the top right-hand part of the screen.
"ROLAND/SOUND" folder on your
"UTILITY," and then press the
PAGE [ ] [ ] buttons
and press the
and press the
PAGE [>] button .
[SHIFT] button while turning knob
[ENTER] button
[ENTER] while holding the
Number of tones in import destination and source
5
If a tone named
check mark as the import destination tone.
* If a tone named
import destination tone, even it was previously edited.
5
To leave the tone as-is, clear the check mark.
9 .
Press the
10 .
To execute, use the
the [ENTER]
The display shows
* Never turn off the power or disconnect the USB flash drive when
or a similar message is shown on the screen, as the unit is processing data.

Importing Scenes

You can import scenes into the JUPITER-Xm as additional scenes that were
exported from the JUPITER-X/Xm.
* You can also import scenes from a backup file.
Saving scenes to USB flash drive
(p. 49)
1 .
Prepare a SVD file with the scenes you've exported from
the JUPITER-X/Xm by using its export function, which you'll
import into the JUPITER-Xm .
2 .
Connect a USB flash drive to your computer .
* If this is the first time you're using the USB flash drive, format it on the
JUPITER-Xm.
&
"Formatting a USB Flash Drive (FORMAT USB MEMORY)"
3 .
Save the SVD file to the
USB flash drive .
4 .
Remove the USB flash drive from your computer and
connect it to the JUPITER-Xm .
Importing scenes into the JUPITER-Xm
1 .
Press the
2 .
Use the [1] knob
[ENTER] button .
You can also make this selection by using the
instead of the
3 .
Use the [1] knob
the [ENTER]
4 .
Use the [1] knob
the [ENTER]
5 .
Use the [1] knob
wish to import, and press the
6 .
Use the [1] knob
use the [2] knob
To select or deselect all scenes, hold down the
turning knob [2].
To select or deselect a certain range of tones, press the
at the beginning of the range, and then press
[SHIFT] button
7 .
Press the
8 .
Use the [1] knob
press the
Reference Manual Ver. 1.5 and later
"INIT TONE" already exists, this is automatically selected with a
"INIT TONE" already exists, it is automatically selected as the
PAGE [>] button .
[2] knob to select
button .
"Import Tone Completed!"
"ROLAND/SOUND"
[MENU] button .
to select "UTILITY,"
[1] knobs.
to select "IMPORT/EXPORT,"
button .
to select "IMPORT SCENE,"
button .
to select the file containing the scene you
PAGE [>]
to select the scene you wish to import, and
to select it with a check mark .
at the end of the range.
PAGE [>] button .
to select where to import the scene, and
[ENTER] button to select it with a check mark .
"OK," and then press
when importing is done.
"Executing..."
(p. 49)
folder on your
and then press the
PAGE [ ] [ ] buttons
and then press
and then press
button .
[SHIFT] button while
[ENTER] button
[ENTER] while holding the
47