Palette Function; How To Use On The Jupiter-X; How To Use On The Jupiter-Xm - Roland JUPITER-X Owner's Manual

Parameter Guide
Parameter Value
500Hz–
RV HF Damp
BYPASS
0 .1–20 .0 s
(*1)
RV Time
5–250 ms
(*2)
RV Level 0–100
Output
D100:0W–
Balance
D0:100W
Level
0–127
List of supported CCs
Parameter Partial 1
LFO1:Rate
LFO2:Rate
WG:Pitch fine
WG:LFO1 depth
WG:LFO2 depth
TVF:Cutoff freq
TVF:Resonance
TVF:LFO depth
TVF:ENV depth
F-ENV:Time 1
F-ENV:Time 4
TVA:Level
TVA:LFO depth
A-ENV:Time 1
A-ENV:Time 4
14
Explanation
Sets the frequencies to cut in
the high-frequency portion of
the reverberation .
The high-frequency portion
of reverb sounds decays
differently depending on the
wall material . This parameter
simulates this kind of high-
frequency decay .
Sets the reverberation time .
Higher values produce longer
reverberations .
* 1 Reverb Type: ROOM1/2,
HALL1–4
* 2 Reverb Type: GATE,
REVERSE, FLYING1/2
Sets the reverberation volume .
Sets the volume balance
between the dry sound (D)
and the effect sound (W) .
Sets the volume level .
Partial 2 Partial 3
29 20 22
14 24 25
21 31 35
26 47 48
15 51 52
3 54 55
9 57 58
28 60 61
81 63 79
83 82 85
86 102 103
16 17 18
30 105 106
89 108 109
90 112 114

PALETTE Function

CC#
The Palette function lets you display the values set for partials 1–4 in
a row and edit them, for the partial parameter you last edited .
Parameter selected by Palette
13
* TVA Level is selected by default .
91
* The partial parameters you edit in the TONE EDIT screen can also
be selected in the Palette .

How to use on the JUPITER-X

12
1 .
Select a JD-800 Model Expansion tone for the
current part .
2 .
Press the [RING], [SYNC] and [XMOD] buttons at the
Partial 4
same time .
23
"PALETTE ON" is shown onscreen, and the Palette function is
27
activated . The [RING], [SYNC] and [XMOD] buttons light up .
46
3 .
Use the [OSC 1]–[OSC 4] sliders to edit the
50
parameter selected in the Palette .
53
The currently selected parameter name and the values for each
56
partial are shown .
59
62
MEMO
80
To turn the Palette function off, change the tone or press one of
87
the [RING], [SYNC] or [XMOD] buttons .
104

How to use on the JUPITER-Xm

19
107
111
1 .
Select a JD-800 Model Expansion tone for the
117
current part .
2 .
Hold down the [SHIFT] button and press the ENV
[AMP] button .
"PALETTE ON" is shown onscreen, and the Palette function is
activated . The ENV [PITCH], [FILTER] and [AMP] buttons light up .
3 .
Use the [A] [D] [S] [R] knobs to edit the parameter
selected in the Palette .
The currently selected parameter name and the values for each
partial are shown .
MEMO
To turn the Palette function off, change the tone or press one of
the ENV [PITCH], [FILTER] or [AMP] buttons .
Currently selected partial
Values set for each partial